Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 909-941-6444
- 9567 Arrow Route Suite #E
Rancho Cucamonga, CA 91730
United States
-
product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
product
Transverse HD Sawmill Meter
MC PRO 1500 HDNC
Finna Sensors built the Transverse HDNC Sawmill Meter to increase the number of potential sensors from 8 to 24. The sensors can now be specified to fit within chain runs and can be located on both the top and bottom faces. This significant increase in surface area allows mills to identify sapwood/heartwood boundary areas or wet pockets for proper sorting prior to kiln drying. Sorting by moisture content has been shown to improve drying productivity by 10% to 15%, as well as, enhance lumber recovery. Further advancements in the software allow users to track packages through the drying process, add Internet of Things (IOT) data and perform advanced analytics with new reports.
-
product
Model B: Concrete Moisture Meter
MRC003305
Specifically designed for the concrete block industry. Includes calibrations for over 34 different kinds of concrete block. Direct reading scales for average percent moisture content.
-
product
Model LGF: Gypsum Moisture Meter
MRC006522
Stainless steel flat plate electrode. Excellent for testing Gypsum Wallboard as it moves or in stacks. Measures moisture in the Gypsum plasterboard 1/4 inch to 3/4 inch thick. Can also check moisture distribution pattern and length or width.
-
product
Handheld Moisture Meters
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
product
Model V: Veneer Moisture Meter
MRC003304
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
product
Model LGF2: Gypsum Moisture Meter
MRC006522-2
Two-range version of the Model LFG. Has 1/2 the normal sensitivity, allowing off-scale indications to be accurately read. Includes carrying case, NiMH battery and operating instructions book. Additional details can be found in product link.
-
product
Model DC-2000-BP: Baled Paper Moisture Meter
DC-2000-BP
Portable hand-held moisture meter provides fast and accurate digital read-out in the range of 5% to 25%. Microprocessor based with large LDC display for easy reading. Pocket-size, weights less than 1lb.
-
product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
product
Model LG: Drywall Moisture Meter
MRC006505
Provides average moisture content down to a penetration of 1in. Uses radio frequency capacitance to measure the moisture content of gypsum wallboard. 0% - 25% moisture range.
-
product
On-Line Moisture Meters
Many methods are available for measuring moisture content on line, in real time: NIR, RF Capacitance, NMR (Nuclear Magnetic Resonance), and Microwave, among others. Finna Sensors is unique in that it has experience with most of these methods and is therefore able to recommend the best possible solution for any application.
-
product
OMNIR: On-Line Near Infrared Sensor
OMNIR is the future of near infrared moisture sensing technology. Coming from OMNI, meaning “all” and NIR, meaning “near infrared,” Finna Sensors has created an intelligent all-sensing solution that exceeds expectations. It not only delivers accurate data instantaneously and non-destructively, it also monitors its own health to perform its best during your crucial processing moments. By selectively harnessing light, to ensure increased uptime and greater profitability for your operation, the future of your manufacturing operation starts now.
-
product
Lab Moisture Analyzer
PC-Based laboratory/production Moisture Analyzer connects through the RS-232 Serial Port. For nuts, granules, powders, pellets, chips or flakes. Complete with:– MCPC-RS Test Chamber– Windows PC-Based Software– Two Sample Cups– Dial Thermometer– Standard Block– RS-232 Cable (10 Feet)– USB to RS232 Adapter– Operating Instructions Manual– 115VAC/60HZ Wall Transformer
-
product
Lumber Moisture Measurement Systems
Improved moisture control has emerged as an important process improvement element in the forest products industry as mills continue to focus on profitability and yield. SCS Forest Products by Finna Sensors provides the industry’s widest-used end-to-end line of integrated moisture measurement systems and related process optimization tools for the sawmill, kiln and planer.
-
product
Model L: Lumber Moisture Meter
MRC003303
Calibrated for 77 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 3/4" penetration. Rechargeable battery.
