Seismic Source Co.
Seismic Source Company is a manufacturer of seismic instruments and data acquisition systems. Its products are used in a broad range of applications: Seismology, Structural Monitoring, Seismic Site Evaluation, Civil Engineering, Gas and Oil Exploration, Industrial Vibration Monitoring.
- (580) 762-8233
- (580) 762-1785
- mail1@seismicsource.com
- 2391 E. Coleman Rd.
Ponca City, OK 74604
United States
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
Dynamite Source Controller
BOOM BOX III
*Easy to Use, just hold the Arm and Charge toggles, Unit charges and is ready to fire*Web based interface allows easy setup and storage of data on PC, Tablet, or Cell phone*Shooter updated with easy to read graphical display and status LEDs*Same unit used for Encoder and Decoder modes
-
product
Event Monitoring System
Sigma 4
Sigma 4 utilizes the “Seismic Acoustic Monitoring” seismograph node. This is the most advanced, field-proven acquisition system in the world. It works seamlessly to provide the most fully integrated source control/recorder solution.*Autonomous Operation using Internal Storage*USB External Storage for Fast Data Collection*Use internal battery option or external power connection*Internal 3C geophone or external Geophone/Seismometer/Hydrophone/Microphone*Supports standard Ethernet equipment
-
product
Fast Timing Analysis
Zero-Time Box
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
product
Hardware/Software for Increased Production
VibLink & NavLink
The VibLink system - Each vibrator, plus the central recorder, is equipped with a VibLink module. The VibLink module uses advanced TDMA techniques to multiplex seven vibrators and the doghouse on one radio channel. And does this all in one second windows. With additional Vibrators, additional seconds are added. The Universal Encoder 3 uses its time slot to send out status updates and request PSS/PFS data. Each Force 3 controller uses its time slot to send out its location, status, and QC Information.
-
product
Networked Seismic Recording System
Distributed DAQlink4
The Distributed DAQlink 4 System is the combination of a standard DAQlink 4 seismograph and internal, high-speed, network extenders. Using inexpensive twisted pair telephone cable, these network extenders will send triggering times and receive seismic data from other DAQlinks. These cable links can send reach 10,000 ft, or three kilometers in length.
-
product
Portable Load Cell System
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
product
Radio Trigger Module
RTM3
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
-
-
product
Seismograph
DAQlink 4
DAQlink 4 is the fourth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system or a distributed seismic reflection system.
-
product
Seismograph
DX6
The DX6 is a 6 channel seismograph that can be used for almost any seismic project. With its internal memory, optional USB memory and GPS, the flexible DX6 node can be deployed anywhere, at any time.
-
product
Software
SourceLink
Specifically designed to maximize production with Continuous Recording Systems like iSeis Sigma, OYO GSR, Fairfield Node, Sercel Unite and all other systems.
-
product
Software
Vscope
The Vscope Software program is used to operate single or multiple DAQlink Units. The Software provides full support to setup unit for autonomous or real-time operation.
