OMICRON electronics
Specialization in power system testing.
- 1-800-OMICRON
1-713-830-4660 - 3550 Willowbend Blvd
Houston, TX 77054
United States
-
product
Partial Discharge Measurements
MPD 500
The MPD 500 simplifies routine factory partial discharge measurements for electrical insulation systems. Engineered with OMICRON's long time experience, the MPD 500 is optimized for routine tests in high throughput environments.
-
product
Three-Phase Test System
TESTRANO 600
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
product
Partial Discharge Measurement and Analysis System
UHF 800
Our UHF 800 is a system for measuring and analyzing partial discharges in the ultra-high frequency (UHF) range in testing environments with high levels of external noise.
-
product
CMC test Set Extender
RXB1
RXB1 extends CMC test sets with 4 additional binary relay outputs. Each binary output channel consists of a normally open ("make") and a normally closed ("break") contact.
-
product
Switch Box for CT Analyzer
CT SB2
The CT SB2 switch box is an accessory for the CT Analyzer which allows automatic testing of multi-ratio current transformers. It is connected to all taps of the current transformer and to the CT Analyzer.
-
product
Three-Phase Relay Test Set
CMC 353
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
product
Protection Test Set
CMC 850
The CMC 850 is a protection test set dedicated to IEC 61850. It focuses on the real-time communication methods GOOSE and Sampled Values to interface with the devices under test.
-
product
Sweep Frequency Response Analyzer
FRANEO 800
FRANEO 800 was developed for testing the mechanical and electrical integrity of power transformers after transportation or exposure to high fault currents. It uses the sweep frequency response analysis (SFRA) principle and measures the electrical transfer function over a wide range of frequencies.
-
product
CMControl P
CMControl P is a control option for CMC test sets, specially designed for the quick manual testing of protection and measurement devices.
-
product
Test Universe
Test Universe is OMICRON's comprehensive and easy-to-use testing software for the CMC device family. It allows you to combine a wealth of application-optimized test modules for creating flexible and fully automated test plans that provide you with an enormous range of functions.
-
product
Voltage and Current Amplifier
CMS 356
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
product
Universal Test Set for Recloser Controls
ARCO 400
ARCO 400 is a smart and rugged testing solution for all recloser controls. It provides the fastest way to perform simple manual trip and close checks. Using the OMICRON Smart Connect technology, ARCO 400 is capable of detecting recloser specific test adapters.
-
product
Handheld Grounding Tester
HGT1
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
product
Programming Interface for CMC Test Sets
CMEngine
CMEngine is an open programming interface that enables you to integrate the CMC test sets into your own testing environment and control them within any type of application.
-
product
Relay Test Set and Universal Calibrator
CMC 256plus
The CMC 256plus is the first choice for applications requiring very high accuracy. This unit is not only an excellent test set for protection devices of all kinds but also a universal calibrator.
