AcQ International
We develop, produce and deliver innovative solutions for a wide range of real-time electronics platforms used in the aerospace, military, industrial automation, transportation, agriculture and space sectors.
- +31 (0)412 641922
- 31 412 622 640
- info@acq.nl
- Alanenweg 6
5342 PV Oss
, 5347
Netherlands
-
product
Stepper Motor Controller for VMEbus
VME321
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
product
CANbus Controller
CPCI360
The CPCI360 CANbus controller is a 3U CompactPCI card based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier messages. Front LEDs provide diagnostic information.
-
product
Audio Card I/O Modules
PIM481-J/DSUB
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
product
CANbus Controller Standard Interface
PCI360
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
product
M-Module Carrier for VMEbus (6U)
i4000
The i4000 is a 6U form factor M-module carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating a mix of M-modules in a VMEbus system. Four M-module mounting sockets are provided by this carrier.The interrupt controller on the i4000 has an interrupt vector register for each M-module interface.
-
product
8 Channel ADC for CompactPCI
CPCI393
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
product
ARINC-429 Controller for CompactPCI
CPCI302
The CPCI302 provides four ARINC-429 compatible channels (2x receive and 2x transmit) at any rate between 12.5 and 100kbps. Because the CPCI302 is built upon a flexible platform, the user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
product
M-Module Carrier for CompactPCI (3U)
i3000
The i3000 M-module Carrier for CompactPCI features a 3U form factor CompactPCI gateway to the M-module interface. One M-module mounting socket is provided by this carrier. This carrier can be used in temperatures from -40°/+85°C. The M-module interface of the i3000 complies to the M-module Specification ANSI/VITA 12-1996. The interface features A8, A24, D16 and D32 access types.
-
product
M-Module Carrier for VMEbus (3U)
i4001
The i4001 is a 3U form factor M-module carrier for the VMEbus and forms the basics of a flexible I/O system. It offers the user a means of integrating M-modules in a VMEbus system. The i4001 has one M-module slot. M-module interrupts can be passed to the VMEbus. The i4001 supports vector-from-module and vector-from-baseboard, this means that interrupt vectors are provided by the the M-module or by the i4001.
-
product
VMEbus
VMEbus (Versa Module Europa bus) is a computer bus standard widely used for many applications and standardized by the IEC as ANSI/IEEE 1014-1987. First developed in 1981 and continues to see widespread use today.
-
product
6 Channel Encoder Input Controller
CPCI323
The CPCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
-
product
Aerospace
AcQ can perform custom developments compliant with ED12/DO-178B and ED80/DO-254 in various design assurance levels (DALs) for safety critical applications, using the ED14/DO160 for the environmental requirements. AcQ also offers standard products for various open standards like VMEbus, CPCI, PCI and other bus standards for test applications and other applications like GPS, display, actuators, data logging and -storage.
-
product
Stepper Motor Controller for PCI
PCI322
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
-
product
RTD Measurement for PCI
PCI390
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
product
Stepper Motor Controller for PCI
PCI321
The PCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.
