Filter Results By:
Products
Applications
Manufacturers
ASTM
ASTM International is a globally recognized leader in the development and delivery of voluntary consensus standards, over 12,000.
See Also: E84
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Flexural Test Methods For Plastics: ASTM D790
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics.
-
product
Tensile Test Methods For Plastics: ASTM D638
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics. ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used.
-
product
AWS Probes For Ultrasonic Weld Seam Testing (ASTM)
SONOSCAN R
The robust ultrasonic probes with BNC connector allow a fast scanning over comparatively large areas with high precision and repeatability. Both our own and third-party wedges can be attached to our probes. . Thanks to the different types of wedges various material tests can be performed.
-
product
Quick Change Probes For Weld Seam Testing (ASTM)
SONOSCAN Q
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
product
Bending Deflectometers For ISO 178, JIS K 7171, And ASTM D790 Compliant Testing
After tensile testing, flexural tests are the most common strength tests for plastics and other resins. The main standards for plastic flexural (bend) tests are ISO 178, JIS K 7171, and ASTM D790, which require very accurate test systems. These standards include flexural strain measurements using a deflectometer, ranging from micro-strain measurements in the elastic region, the reversible elongation at the beginning of tests, to larger strain measurements in the plastic region. Shimadzu's deflectometers integrate easily into AG-X plus series, AGS-X series, and EZ-X test frames and Trapezium X testing software. Since these deflectometers push up against the specimen from below, the specimen color is not a limiting factor, as can be for laser type non-contact deflectometers. Furthermore, these deflectometers can partially absorb the shock during specimen failure, preventing specimen fragments from scattering.
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron® TestMaster AT3 and AT3+ Automated Testing System utilizes an innovative design for the automatic tensile and/or flexural testing of plastic specimens. Meeting the testing requirements of ASTM D638 and D790, ISO 527 and 178, as well as other testing standards, this system offers many of the benefits of our robotic AT6 systems, but in a smaller footprint.
-
product
45 Degree Flammability Tester
TF310
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, is to determine the fabric flammability (fabric burning test) under controlled conditions, complies with standards like 16 CFR Part 1610, ASTM D1230, ASTM F2100.
-
product
45 Degree Flammability Tester
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, to determine fabric flammability under controlled conditions total automatically(fabric burn test). 45 Degree Flammability Tester complies with ASTM D1230, CALIF TB117, FTMS191-5908, etc. Our product is the best choice for you when you do flammability test for fabric in flammability testing labs.
-
product
6-Axis Robotic Automated Testing System
AT6
The Instron AT6 Automated Testing System utilizes an innovative design for the automatic tensile and/or flexural testing of metals, plastics, thin films, components, elastomers, sutures, and composites. Conforming to ISO and ASTM standards for a wide range of materials, this system has a flexible platform to deliver high throughput with repeatable results for a variety of testing needs.
-
product
8-Position Dissolution Tester
Vision G2 Elite 8
The Vision G2 Elite 8 dissolution tester is a versatile performance machine, built with the highest quality components and engineering. The G2 Elite 8’s ergonomic design and workhorse performance make it ideal for automation and extended applications as well as for 8-sample manual testing. The G2 Elite 8 meets and exceeds worldwide standards including compliance with USP, US FDA, ASTM, EP, JP, CE, CSA, RoHS, and 21 CFR Part 11.
-
product
Acid Number and Acidity Tester
LD-LAAT-A11
LabodamLD-LAAT-A11is designed as per ASTM D664-11a Test Methods for Acid Number of Petroleum Products and Test Methods for Acidity of Gasoline, Kerosene, and Diesel oil.
-
product
Acid Number Tester
LD-LAAT-A12
LabodamLD-LAAT-A12is automated and controlled by microprocessor. It is designed and made as per the ASTM D664-11a Test Methods for Acid Number of Petroleum Products.
-
product
Adhesion Test Analyzer
PA-917010
The Adhesion Test Analyzer (ATA) takes all of the guess work and subjectivity out of rating the classification of your adhesion results as defined in the ASTM D3359 standard, and is accomplished with one simple instrument.
-
product
Analog Surface Profile Gauge
NOVOTEST LIMIT
Mechanical depth gauge is designed to comply with ASTM D 4417-B, SANS 5772, US Navy NSI 009-32, US Navy PPI 63101-000 for (depending on configuration): measures the peak-to-valley height of a blast cleaned surface; measurement the depth of focal corrosion; measures depth of narrow holes and grooves.
-
product
Apparent / Bulk Density Tester
Bulk Density Tester Series
The Apparent Density Tester - Bulk Density Tester series testers are used to measure apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. There are three methods according to ASTM D 1895 that are applicable to various forms of these materials that are commonly encountered - from powders and granules to large flakes and cut fibers. The apparatus consists of a measuring cup which is polished inside and a funnel.
-
product
Automatic Extensometer
SIE-560A/560SA
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with high accuracy, and provide automated functions that increase testing efficiency and test reproducibility. Ideal for testing a wide variety of materials, including metallic materials, plastics, and composites, the SIE-560A series complies with ISO 527, JIS K 7161, and ASTM D638 standards for plastics tensile testing. In addition, the SIE-560A series supports strain-rate controlled metallic material tensile testing measurements specified in ISO 6892, JIS Z 2241, and ASTM E4
-
product
Automatic Kinematic Viscosity Tester
K623
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the kinematic viscosity of lubricant oil and other petroleum products at precisely controlled temperatures. Kinematic viscosity is of primary importance in the design and selection of a wide range of petroleum products. Conforms to GB/T 265 and ASTM D445.
-
product
Automatic Ozone Test Chamber
EKT-2001OZ
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (O3) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
Automatic Single Yarn Strength Tester
TESTEX Testing Equipment Systems Ltd.
Single Yarn Strength Tester,to determine breaking strength and elongation of single cotton, wool and other yarns up to 50 N. Yarn Strength Tester complies with ASTM D2256, ISO2062, GB/T14344,etc. Please contact us for more information about yarn strength testing methods.
-
product
Automatic Softening Point Tester
LD-LSPT-A10
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
product
Automatic Tag Closed Flash Point Tester
LD-LACF-A10
Automatic Tag Closed Flash Point TesterLD-LACF-A10is a highly automated machine with -50°C lowest flash point and simple operations. Used to determine flash point of liquids with viscosity below 5.5 cSt (mm2/s) at 40°C (104°F) or below 9.5 cSt (mm2/s) at 25°C (77°F) and flash point below 93°C (200°F) . Test method is complied with ASTM D56 international standard.
-
product
Auto Water Vapour Permeability Tester
TESTEX Testing Equipment Systems Ltd.
Auto Water Vapour Permeability Tester, to determine the water vapour permeability of various textile and garment fabric, coating fabric, composite, sportswear and industrial fabrics. Auto Water Vapour Permeability Tester complies with ASTM E96, ISO8096, BS 3424, etc.
-
product
Auto Water Vapour Permeability Tester
TF165B
TESTEX Testing Equipment Systems Ltd.
Water Vapour Permeability Tester, also called Water Vapor Transmission Rate Tester (WVTR Tester) is to determine the water vapor permeability of various textile and garment fabrics, coating fabric, composite, sportswear, and industrial fabrics. This tester complies with ASTM E96, GB/T 12704, JIS L1099, etc.
-
product
Averaging Clip-on Extensometer
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
Ball Rebound Tester
Hildebrand Prüf- und Meßtechnik GmbH
The ball rebound tester is used to determine the resilience of foam materials in accordance with DIN EN ISO 8307 and ASTM D 3574.
-
product
Barcol Hardness Impressor
BHI
Measures the hardness of soft metals such as aluminum, aluminum alloys, copper, brass, and other materials such as harder plastics, and fiber-reinforced plastic. Easy-to-read digital display. Comparable to 934-1 Barcol Hardness Tester. Conforms to national and international standards including ASTM.
-
product
Base Number Tester
LD-LAAT-A13
LabodamLD-LAAT-A13is composed of automatic potential titrator and titration device. It is designed according to Industry Standard of Petrochemical and follows ASTM D2896 and ASTM D4739 Test Methods for Base Number of Petroleum Products.
-
product
Biaxial Clip-on Extensionmeters
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen and a third sensor measures transverse strain. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
Biodiesel In Diesel Analyzer
InfraCal 2 ATR-B
The InfraCal 2 Biodiesel Blend Analyzer for measuring percent biodiesel in diesel is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive biodiesel blend analysis is needed. The InfraCal 2 ATR-B is based on proven IR technology, originally developed by Wilks, and used by fuel distributors, blenders, producers and regulatory agencies worldwide. The compact, easy-to-use Biodiesel Blend Analyzer has a measurement range of 0 – 100% biodiesel in diesel. These results are comparable to both ASTM D7371 and EN 14078, laboratory methods that require expensive FTIR Spectrometers.
