Filter Results By:
Products
Applications
Manufacturers
Ground Continuity
Verifies ground is present.
- TEAM SOLUTIONS, INC.
product
12-bit, 4 Analog Voltage Outputs With Separate Grounds, Optically Isolated 500 V
APCI-3504
4 analog output voltage channels with 500V optical isolation, 12-bit resolution, each output has its own ground line.
-
product
2 in 1 LAN Tester
PLTM20
Tests Pin Configuration for 10 Base-T, 10 Base-2, RJ45/RJ11, 356A, TIA-569A/568B and Token Ring CableRemotely Test Cables Up to 330 Yards AwayTest Ground WireMeasure DC/AC Voltage, DC/AC Current, Resistance, Continuity, and DiodeDC Voltage: Max Range 600 V, Accuracy +/- 0.5%AC Voltage: Max Range 600 V, Accuracy +/- 1.2%DC Current: Max Range 200 mA, Accuracy +/- 1.2%AC Current: Max Range 200 mA, Accuracy +/- 2.0%Resistance: Max Range 20 M, Accuracy +/- 0.8%Continuity Test: Beeps If Less Than 100 Accessories Included: Test Leads, LANtest Remote Terminator, 9V Battery, Carrying CaseDimensions: 6.38' H x 2.93' W x 1.73' DWeight: 10.86 oz.Sold as : Unit
-
product
Ground Continuity Tester - 25, 30, 35 AMP
M25, 30, 35
Production / Quality Assurance Testing - Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures ground continuity from ground to the power cord ground pin of the DUT. Interface enables interconnection to any ROD-L Hipot & Leakage testers to form a complete automatic test system.
-
product
Leakage Current Tester
M450LT
Performs leakage current tests in compliance with IEC 601, UL 544, UL 2601 and other medical and non-medical standards. Add Rod-L Hipot & Ground Continuity testers to build a complete modular automatic test systerm
-
product
Ground Bond Tester
264
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
DC Hipot Test Instrument
M100DC
Performs concurrent ground continuity test. ARC and OVERCURRENT detection circuits. Fast discharge of Device Under Test (DUT) and other test standards
-
product
Automated AC Digital Hipot Tester
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
product
Voltman True RMS Industrial Safety Voltmeter
125
If you need a continuity function or harmonics are a problem then the Voltman TRMS is for you. Non sinusoidal waveforms from variable speed motors cause problems for most meters but the Voltman TRMS meter is specifically designed to produce accurate and dependable readings of distorted waveforms. When there is no voltage present the unit automatically tests for continuity, ground faults or shorts.
-
product
Volt Tester
PPTACT1CS
THE PROBE 12-Volt Test Light with Haptic Feedback, (PPTACT1CS) this tool vibrates and lights when voltage over 12 volts is detected. When a voltage is below 12 volts, this functions as a standard test light. Just push the button and go! Shows positive voltage, ground, and continuity “all in one tool” with haptic advantage.
-
product
Multi-purpose Cable Tester and Cable Tracer
165 CB
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
Breakout Box
T1000-9
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
product
12 Plug Pro Audio Cable Tester
PCT40
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
product
5 kV AC Hipot Testers
Models M100BVS5 & M500BVS5
Now you can perform safe, rapid and efficient hipot testing, ground continuity testing, and total or real current monitoring in one simple operation. The ROD-L Electronics model M100BVS5 and model M500BVS5 hipot testers perform safe and accurate AC hipot and ground continuity testing in compliance with UL, IEC, CSA, VDE, FCC and other electrical equipment testing standards
-
product
AC Hipot Tester
298
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
product
DC Hipot Tester,
294
Our Model 294 is a simple-to-use DC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 294 DC Hipot Tester includes all the features you need to get the job done and move on. Make testing simple with common sense security settings. PLC Remote allows you to make DC Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
product
Test Probes
Our innovative Test Probes are the upgrade version of Auto Multi Meter. It can perform multiple circuit system test such as power supply feed, voltage and resistance measurement, continuity test, ground test, polarity check and components activation.
-
product
ELECTRICAL TEST Kit
1021 TK
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Breakout Box
T1000-37
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
product
DC Hipot with Insulation Resistance Tester
297
Our Model 297 is a simple-to-use Hipot Tester with the built-in ability to easily test Insulation Resistance and Ground Continuity (Low Current Continuity) in a one-box solution. The 297 is capable of performing Hipot Tests in both AC & DC currents. Make testing simple with common sense security settings. PLC Remote allows you to make Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
AC Hipot Tester
295
Our Model 295 is a simple-to-use AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). You need a Hipot Tester that includes all the features you need to get the job done, the 295 has what you're looking for. Make testing simple with common sense security settings. PLC Remote allows you to make AC Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
Advanced Cable Tester v2
TP800110
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
product
Protector Conductor Test / Ground Continuity Test / Ground Bond Test
Testing the protective conductor is indispensable for assemblies, devices and systems of protection class I because it reduces the risk of life-threatening electrical accidents.The test checks whether the protective earth (PE) fulfils the criteria specified in the standards and can correctly discharge the current occurring in case of a fault.The ground continuity test checks whether the protective earth conductor is connected continuously to all metallic enclosure parts that can be touched by the user. The test can be carried out with low currents and voltages (simple continuity test).
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
Self-reclosing Overcurrent And Residual Current Protection
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
