Filter Results By:
Products
Applications
Manufacturers
-
product
Harmonics and Flicker Testers
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
product
Harmonics & Flicker Analyser
AC2000A
The Laplace Harmonics and Flicker analyser provides the user with a complete system for testing product compliance with IEC61000-3-2 and IEC61000-3-3. Quick and easy to use, the built-in screen provides a clear pass/fail indication of compliance status, plus a full listing of results for each harmonic, in either tabular of bargraph format. The instrument is properly configured to cope with fluctuating harmonics. The Flicker mode provides proper measurement of short term and long term parameters, using algorithms specified in IEC61000-4-15. In addition, inrush current measurements can be automated such that the product under test can be automatically cycled on/off with user entered time profiles.
-
product
Light Flicker Meter
LiFli
The LiFli light flicker meter enables fast evaluation of light sources on the flickering part (flicker / flicker). Especially in the case of LED lamps, the flicker portion can be determined only by one measurement, since it is in the range of 0% to 100% for these luminous means.Audio features enable the flicker to be reproduced acoustically. A voltage output for further analysis by means of oscilloscope or voltage analyzer is available.
-
product
Harmonic Flicker Generator 01
The Harmonics & Flicker Generator (HFG01) has been designed for the purpose of verifying harmonic and flicker test equipment. It provides an easy and reliable way to externally check the performance of the measurement system to the EN/IEC 61000-3-2 harmonics and EN/IEC 61000-3-3 flicker standards; particularly important as these tests rely on software control and calculation, and for which there is no intuitive sense of the response.
-
product
Harmonics And Flicker Measuring System
ProfLine Series
The Teseq ProfLine system is a complete and cost effective Harmonics and Flicker measurement test system which compiles to the latest IEC/EN standards, including IEC 61000-3-2 and IEC 61000-3-3. The programmable power generation capability of up to 45 kVA (90 kVA and 145 kVA sources comprise multiple 45 kVA units) provides more than ample power to cater for a wide range of Equipment Under Test (EUT).
-
product
LFA-3000 Light Flicker Analyzer
Hangzhou Everfine Photo-E-Info Co., LTD
LFA-3000 can simulate flickering measurement and analysis under various voltage fluctuation conditions, and the system has built-in standard voltage waveform database, one operation can complete the test and analysis of IEC 61547-1, convenient and fast. Meet the lighting product design, quality inspection and application of flickering test analysis needs.
-
product
Flicker Measuring Probe for LCM ATS
A712306
The Chroma A712306 Flicker Measuring Probe for LCM ATS is specifically designed for adjusting the flicker on LCM automatically following the FMA(Flicker Modulation Amplitude) standards defined by VESA (Video Electronics Standards Association) and JEITA (Japan Electronics Information Technology Industries Association) for flicker measurement.
-
product
Lamp Start, Run-up time and Flicker Test
LSRF-2
The (EU) NO 1194/2012rules
. Compared with which posted by theEuropean Commission Regulation (EC) NO 244/2009 Regulations dated 18th March, 2009, the new rules have complete mandatory and eco-design requirements. Start and Run-up time as the two indicators functional requirements in the industry has been more emphasis by manufacturers. -
product
Spectral Light And Color Meter w/ Flicker measurement
BTS256-EF
Spectroradiometer for the illuminance (photopic, scotopic, melanopic), spectrum, light color, color rendering index, and flicker. Cosine field of view illuminance measurement for accurate evaluation of extended illumination. Flicker measurement. Spectral measurement technology, required for LED light, color, color rendering, color effects. Photodiode for synchronization to pulse width modulated light and flicker measurement.
-
product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
product
Ambient Light Sensors
ST offers innovative ambient light sensors (ALS) that provide, in optimized package size, accurate information on ambient light, like the Illuminance (lux) level, the color temperature or the light flicker frequency.
-
product
Camera Detector
P7030
The easy to use Camera Detector is so small it can be carried or stored anywhere. Discreet sweeps of the home, office or hotel room can be done quickly and efficiently. When a camera is discovered, a LED light flickers and an audible alarm sounds. An auto adjusting sensitivity tuner allows you to scan variable distances and can check multiple channels. It can detect frequencies anywhere from 50 MHz to 3 GHz, picking up most wireless cameras.
-
product
Cold-Atom Frequency Standard
Rack-mount microwave atomic clock using laser-cooled 87Rb atoms. Production unit target specifications: Allan deviation 2×10-12 @ 1 s, 2×10-14 @ 104 s; flicker floor 1×10-14; absolute accuracy < 1×10-13.
-
product
Compact Recorders
Reduce fleet and labor costs with this small, rugged, lightweight recorder. The Revolution allows you to retrieve data wirelessly with Bluetooth®. The included ProVision software lets you monitor current, flicker, voltage, power and more from your computer.
-
product
Display Measurement Systems
DTS Series
Instrument Systems Optische Messtechnik GmbH
Characterization of emissive, transmissive, reflective, and transflective displaysViewing-angle-dependent analysis of illuminance, contrast, color, and derived parametersDetermination of the electro-optical transfer function: analysis of luminance, contrast, and color depending on electrical driving conditionsMeasurement of transient properties, such as switching times, flicker, and modulation
-
product
DMX current dimmer
LDC-41
4 channel DMX driver/dimmer for 350-1000mA constant current LED products. Drives RGB, RGBW, RGBA or 4 channels of single colour products. 2-12 LEDs per channel, depending on your choice of external power supply. 16 bits dimming curve for extremely smooth dimming. Absolute flicker free for use in TV studio's and theatres. DIN rail mounting system. Digital setting of various functions.
-
product
EMC Compliance Test Systems
ECTS2
Now in its second generation, the ADAPTIVE POWER EMC Compliance Test Systems use a greatly enhanced harmonics and flicker measurement system and newly designed flicker impedance options to support single and three phase AC harmonics, flicker and AC and DC immunity compliance testing up to the maximum required current of 75A per phase.
-
product
EMC Test Systems
IEC61000
N4L are the only IEC61000 EMC test system manufacturer in the world* with an on site UKAS ISO17025 calibration laboratory offering accreditation to IEC61000-3-2, IEC61000-3-3, IEC61000-4-7 and IEC61000-4-15. Calibration and trace-ability are a vital aspect of any EMC test solution and the coverage provided through N4L’s UKAS Laboratory is comprehensive. N4L’s IEC61000-4-15 calibration procedure is particularly noteworthy as it covers the entire test protocol detailed in Annex C of IEC61000-4-15. It is commonplace for specific parameters within IEC61000-4-15 (d parameters are frequently omitted from calibration procedures) to remain untested during typical flicker calibration due to the difficulty in providing trace-ability for such measurements. All tests within the test protocol of Annex C are included within the scope of accreditation and calibration procedures at N4L.
-
product
Flat Panel Display Test Solutions
Support 8K SHV (Super Hi-Vision 7680x4320 / 8192x4320)Support full 8K scrolling functionIndependent signal and power module designDual-core graphics processing architecture - Increase graphics and data transmission performance - 8K Super Hi-Vision images switch in less than 200msSupport 6/8/10/12 bits color depth (12 bit only in LUT mode)Support user edited test patterns - BMP pattern format - Maxi. 300 of 8Kx4K bmp patternsSupport VDIM and PWM dimming functionSupport cross coordinates defect positioning functionSupport auto flicker adjustment (with A712306)Support gigabit Ethernet control interfaceSupport USB port for data update
-
product
For Flaw Detection, Thickness & Dimensional Measurement In Tube & Bar.
ECHOMAC® FD6 MULTICHANNEL UT
*Versatile Ultrasonic tester with superior performance and versatile, intuitive operation.*For full inspection of tubes, pipes and bars, plate and weld.*Operate on or off line.*Upgrade and/or replace older ultrasonic testers.*Use with rotary, spin-the-tube, squirter and bubbler installations.*Vivid, real time, flicker free full color display of test signals, thresholds and settings.*Up to 32 independent channels in one instrument.*Model 6A is GE Qualified as of 9-6-16 for P3TF31 Class A & B, & P29TF82 Class A & B, typical requirements for nuclear and aerospace applications.
-
product
Harmonic/Flicker Analyzer for IEC61000-3-2/3/11/12, IEC61000-4/7/15
KHA3000
KHA3000, in addition to the complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*. Furthermore, the KHA series is compliant with two measurement technique standards, the existing and the latest versions, so you can simply select to take measurements for the latest standard including interharmonics and for the conventional integral multiple harmonics without using any other device. In addition to the real-time display that can be used like an oscilloscope and FFT analyzer, the unit offers the real-time judgment of compliance with standards. Using this unit alone, you can judge test results and prepare result reports without the use of a PC. On top of that, you can easily set up a test system by combining KHA3000 with an AC power supply (PCR-LA Series) and a line impedance network (LIN40MA-PCR-L).
-
product
HDR USB Camera With LFM
See3CAM_CU22
See3CAM_CU22, is a 2MP color USB 3.1 Gen1 SuperSpeed camera featuring High Dynamic Range (HDR) with LED flicker mitigation (LFM). This HDR camera is based on 1/2.5" AR0233AT CMOS image sensor and a dedicated high-performance Image Signal Processor (ISP). It can produce excellent images even under low light conditions. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux.
-
product
LCD Display Optical Measurement System
RayClouds Photoelectric Technology Co.,Ltd.
LCD display optical characteristics automatic measurement system is mainly used in LCD, LED screen, OLED screen, FPD, Mini LED, Micro LED and various new luminous materials.LCD display optical characteristic automatic measurement system supports the test of optical performance parameters such as viewing angle, luminance, uniformity, contrast, chrominance, response time, flicker, and refresh rate, etc.
-
product
Loggers/PQA
Kyoritsu Electrical Instruments Works, Ltd.
Large capacity for storing 60,000 data points Lowpass Filter will filter out the harmonics LED flickers when the preset current/voltage value is exceeded CALL:Confirmation of recorded data Selection of One-time mode or Endless mode Non Volatile Memory Battery power indicator The userfriendly PC software "KEW LOG Soft 2" is supplied Continuous measuring time:Approx. 10 days (Alkaline Battery)
-
product
Luminance Colorimeter
RayClouds Photoelectric Technology Co.,Ltd.
Measurement parameters: luminance, chrominance, color temperature, flicker, Gamma, etc.Applications: mobile phone screens, small flat panel displays, TV displays, etc.
-
product
Luminance Colorimeter
RD Series
RD series can measure not only luminance and chromaticity, but also response and flicker for display and light source.
-
product
Meter Testing
METES
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
product
MRI POWER SUPPLIES
MRI Power Supplies are used in MRI Imaging rooms in hospital environment. The lights in the MRI rooms require DC power. If AC power is used, the quality of the MRI imaging process is compromised. These units are ideal for MRI room, where a 60 Hz flicker free light environment is desired. CEHCO offers four models which are shown below.
-
product
Portable CCD Spectroradiometer
LMS-6000
The Portable CCD Colorimeter Spectroradiometer has the following versions which can measure different parameters: • LMS-6000: illuminance (lux), E(Fc), Ee(W/m2), Tc (K), Duv Correlated Color Temperature (CCT), Chromaticity Coordinates, CRI, Purity, Peak Wavelength, Dominant Wavelength, Half Bandwidth, Center Wavelength, Centroid Wavelength, Total Color Difference, Brightness Difference, Red-Green Degree, Yellow-Blue Degree, CCT Difference, SDCM Diagram, Spectrum Diagram • LMS-6000L: cd/m2, fL, Tc (K), Duv Correlated Color Temperature (CCT), Chromaticity Coordinates, CRI, Purity, Peak Wavelength, Dominant Wavelength, Half Bandwidth, Center Wavelength, Centroid Wavelength, Total Color Difference, Brightness Difference, Red-Green Degree, Yellow-Blue Degree, CCT Difference, SDCM Diagram, Spectrum Diagram • LMS-6000P: LMS-6000 Parameters+PAR, PPFD, YPFD, Blue-purple irradiance Eb, Yellow-green irradiance Ey, Red-orange irradiance Er, Ratio of red and blue radiation Erb_Ratio • LMS-6000S: LMS-6000 Parameters+PAR, PPFD, YPFD, Blue-purple irradiance Eb, Yellow-green irradiance Ey, Red-orange irradiance Er, Ratio of red and blue radiation Erb_Ratio, Rf and Rg according to TM-30 • LMS-6000F: LMS-6000 Parameters+Flicker test • LMS-6000B: LMS-6000 Parameters+Blue Light Hazard Weighted Irradiance according to GB/T20145, CIE S009/E:2002 • LMS-6000BF: LMS-6000 Parameters+Flicker test, Blue Light Hazard Weighted Irradiance according to GB/T20145, CIE S009/E:2002
-
product
Power Quality Analyzer
PQA-300
PQA-300 Power Quality Analyzer offers the latest functionality and measurement technology designed specifically for the Utility industry. The PQA-300 is a compact solution to address; Flicker PST and PLT, Voltage and Current imbalance, Sags, Dips and Swells, harmonics, inter harmonics, THD, RMS Voltage and Current, Phase and Time measurement.
