Filter Results By:
Products
Applications
Manufacturers
-
product
Millimeter Wave Continuously Variable Waveguide Attenuators
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
product
Waveguide Twists
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Waveguide Probes
We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.
-
product
Waveguide Loads
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
product
Waveguide To Coax Adaptors
The transitions from waveguide to coaxial line (SMA connector type) are offered up to 110 GHz.
-
product
Waveguides
Learn about waveguides at Precision MMW. This is a handy waveguide tutorial for the everyday mmWave engineer.Learn more on Waveguides at Precision website here.
-
-
product
Waveguide Twists
Fairview Microwave’s precision waveguide twists operate from 18 to 110 GHz across seven frequency bands with waveguide sizes ranging from WR-42 (18 GHz) to WR-10 (110 GHz). Our portfolio of waveguide twists feature gold plated brass construction that offers excellent electrical performance with VSWR as low as 1.02:1 and insertion loss as low as 0.2 dB. Both 45° and 90° waveguide twists are available from stock, with the 45° versions being available in both right hand and left hand twist configurations. All of our waveguide twists are in-stock and ready to ship today!
-
product
Flexible Waveguide
Flann offers a number of solutions for flexible waveguide interconnect including waveguide-coaxial-waveguide and semi rigid. Traditional flexible waveguide solutions are available on request.
-
product
H Bend Waveguides
H-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles. It directs the radio frequency beam and "bends" the signal to go the direction you want.View more H-Bend Waveguide
-
-
product
Waveguide Calibration Kits
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
product
Millimeter Wave Antennas
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
product
Waveguide to Coaxial Adapter
D8-AWC84SK-1296
Waveguide to Coaxial Adapter, Frequency 6570~9990MHz, 50W, Rect. Waveguide FBP84, SMA Female
-
product
Double Ridged Waveguide Horn
DRH40
Frequency range: 4 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
product
WR-12 Waveguide Straight
WAG-12-SXX
• 60 GHz to 90 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-12 Waveguide Straight
-
-
-
product
Waveguide Power Splitters
*Low Insertion Loss*Coverage of full Waveguide Band*Available from 50 GHz up to 325 GHz
-
product
Waveguide Bends
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
product
Waveguide
NC346
The NC346 Series waveguide is designed for narrow-band high ENR noise figure measurement applications. For high power waveguide systems the series has an optional built-in isolator to provides very low VSWR and superior flatness, typically <= +/- 1.5 dB.
-
product
Manual Attenuator (Waveguide)
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
-
product
Right Angle Waveguide to Coax Adapters
Fairview Microwave right angle waveguide to coax adapters include millimeter wave frequency ranges with models in the K-band (18 to 26.5 GHz) up to the V-band (50 to 65 GHz). These right angle waveguide to coax adapters offer excellent VSWR as low as 1.29:1, while also providing insertion loss performance as low as 0.3 dB. Waveguide sizes available for these new 90 degree coaxial adapter models include WR-42, WR-28, WR-22, WR-19 and WR-15. These coax to waveguide adapters in a right angle design are ideal for numerous applications requiring a transition from coaxial cable to waveguide or vice versa, including SATCOM, wireless communications, industrial, test and measurement and defense systems. Fairview’s new waveguide to coax adapter products feature a right-angle configuration, those with 2.92mm connectors use a UG-style square waveguide flange, 2.4mm and 1.85mm connector versions use a UG-style circular waveguide flange. Both male and female connector options are available in each right angle waveguide to coax adapter frequency band.
-
product
Millimeter Wave Frequency Counter 70-170 GHz
Insight Product Co. offers the electronic frequency counter for frequency measurements of millimeter wave generators of continuous or pulsed signals. The counter has an auto and waiting modes of operation and a direct 6-digits reading in frequency range (70-170) GHz without an external mixer.
-
-
product
Double Ridged Waveguide Horn
H-A40
Frequency range: 26 GHz - 40 GHz VSWR (max): < 1.3:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
product
Waveguide Amplifiers
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
product
Waveguide Adapter
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
