Filter Results By:
Products
Applications
Manufacturers
Potentiometers
Measure the voltage in a circuit or function as voltage dividers.
See Also: Programmable Resistors
- Pickering Interfaces Inc.
product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Motorized Potentiometer
Mounting On Circuit Board Or DIN Rail
INELTA Sensorsysteme GmbH & Co. KG
*PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch
-
product
Dekatran Decade Ratio Transformer
DT1145
The DT1145 is TEGAM''s only bench or panel mountable, decade transformer solution. It features three decades plus an interpolating potentiometer for fine tune adjustment of ratio signals to 1.11100. The unit has an exceptionally low output impedance for high current applications of up to 1 Ampere.
-
product
Ultra-compact 3.6" LCD Weather Resistant Monitor
Uni-Vu3 WS
Mounted in an extruded aluminium housing, and fully sealed to IP 65 standard, Uni-Vu3 is an ultra compact LCD monitor suitable for on-camera use in exterior locations. Murraypro ensure that only professional quality components are present on the Uni-Vu3, there being no place for flimsy pre-set potentiometers or low-cost slide switches on a Product for Professional use!
-
product
Automated Potentiometer Systems
Measurements International Ltd.
Intrinsically Accurate Self-Calibrating Ratio Divider, Best Accuracy < 0.05 ppm, Built-in 20-Channel Scanner, Arbitrary Voltages from 1 mV to 1200 V, Bipolar Voltage Measurements, Calibration of Fluke 5700A/5720A, Calibration of 3458A and 8508A, Calibration of Voltage Ratio Dividers (F752A, MI 1340A, G7520), Linearity Calibration of Digital Volt Meters (DVM), Traceability to 10 V Zener Reference.
-
product
12 Pulse SCR Controlled High Voltage Power Supply
- 12 Pulse SCR Controlled Power Supply, P/N 19435PS- Input: 480 VAC, 300 Amps, 3 PH, 60 Hz- Output: 0 to 3000 VDC ± 10%, 80 Amps max adjustable with potentiometers, and 4/20 mA input signals from the PLC- Output voltage and current are provided as 4/20 mA signals to PLC- Contactor and overload relay are installed for protection- Power ON Light- Start / Stop capability- EPO capability- Manual voltage control and current limit- PLC interface- Output voltage and current are displayed on the voltmeter and ammeter.- A selector switch is used to select between manual Control or PLC Control- The customer is responsible for the PLC controller and PLC programming- Power enclosure, 68″H x 65″W x 44″D- Control enclosure: 20″H x 16″W x 9″D- Weight: 5000 lbs. approximately- All input/output connections are inside the enclosure
-
product
Rotator Controller
RA-S1
The RA-S1 has four buttons that are used for configuration and to manually turn the rotator. It has two potentiometers POS and SPEED. POS is used to choose an angle to point-and-shoot and also choosing between options when the RA-S1 is on the setup mode.
-
product
Displacement Transducers
Displacement transducers, non-contact displacement sensors, LVDT sensors, LVIT sensors and potentiometers with a variety of electrical outputs to measure and transmit travel ranges.
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Configurable Reostat or Potentiometer Module
YAV90084A
4x 8-Bit 1KOhm reostat4x 8-Bit 40 Ohm reostat2x 8-Bit 5 MOhm reostat10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in self test10x Voltage to current source 0(4)..20mA10x Analog Outputs (buffer for voltage or frequency)36-Ch Test Point voltage divider2xCAN Bus Channels Terminators testerExpandable with NI PXI-6723 and PXI-6345.
-
product
IGBT Power Supply, 120 KW, 0 to 16 VDC, 7500 AMPS, P/N 6132C
IGBT Power Supply, 120 KW, P/N 6132CInput: 480 VAC, 3 PH, 60 HzOutput: 0 to 16 VDC, 7500 AmpsRipple does not degrade when the output voltage is reducedDigital remote with Voltmeter and Ammeter and potentiometers includedDimensions: 20.00”W x 67”H x 24.5”D.Estimated weight: 600 lbs.
-
product
Hydrostatic Level Sensor
2250
The Signet 2250 Hydrostatic Level Sensor for level and depth control has a one-piece injection-molded PVDF body and ceramic diaphragm for superior compatibility in corrosive liquids. Utilizing hydrostatic pressure, the 2250 Level Sensor disregards false level signals from steam vapors, foam or any other debris on the liquid surface. Two pressure ranges allow for optimal resolution matched to your sensing needs. Solid state circuitry eliminates drift (no internal potentiometers).
-
product
Potentiometer for OEMs
FlexiPot
The best user interface, whether in consumer electronics or industrial controls, contains sensors that cause minimal interference, meaning the user may not even know they are there. FlexiPot, by Tekscan, is a flexible membrane potentiometer with an ultra-thin (0.008"), lightweight profile. Low power requirements combined with a linear output make it the ideal position sensor, from both a manufacturing perspective as well as a user perspective.
-
product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
Trimmer Potentiometers
CTS trimmers are typically used in applications that do not need frequent adjustment and are often used for "set and forget" initial adjustments in circuits. These are usually located on the circuit board and out of view. CTS trimmers are available in a variety of standard resistance values, tolerances, power ratings, and mounting styles. Depending on product series, adjustment knobs are available with color coding and a screwdriver and/or hex hole for top or bottom side adjustments.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
Universal Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Universal Transmitter for temperature, load cells / strain gauge, potentiometer and resistance in 6 mm housing. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Motorized Potentiometer
INELTA Sensorsysteme GmbH & Co. KG
More than 10.000 Variants. Free configurable.
-
product
DC Power Supplies
DCS Series
AMETEK Programmable Power, Inc.
The DCS Series of 1 kW, 1.2 kW and 3 kW programmable power supplies provides a highly reliable power platform. It utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low profile chassis. This DCS power supply family has an easy-to-use front panel with 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overtemperature, remote programming, shutdown and over voltage protection, status and constant-voltage/current mode operation. The DCS 3 kW Models have push button control of the output standby mode, OVP reset, remote/local programming and preview status of voltage, current and OVP setpoints.
-
product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Automotive Rotary Potentiometers
Panasonic Industrial Devices Sales Company of America
Panasonic Center Space Rotary Potentiometers offer built-in LED options and automotive operating temperatures. Target markets include Automotive and Measurement Equipment.
-
product
PXI Resistor Module Dual 24-Channel (no resistors fitted)
40-281-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Power Supply
5200
The Model 5200 is a basic unregulated power supply that is designed for use with Magtrol's Hysteresis Brakes and Clutches. The 5200 is available in either 12, 24 or 90 VDC voltages, corresponding to the available hysteresis brake/clutch coil voltage options. Braking control is enabled via a 10-turn potentiometer and adjustment knob located on the front panel.
-
product
Capacitive Sensors
*High noise immunity*Sensing range adjustable by means of potentiometer or teach button*Plastic or metal housings for different applications*Sensors for position and level detection*Accessories for mounting on tanks or sight glasses
-
product
Mini-Joystick Potentiometers
The CTS mini-controllers offer these features often found in many larger products:A choice of through hole or surface mountingA long 1 million cycle lifeA variety of resistance and tolerance optionsExcellent electrical accuracy with a patented mechanism (Pat. Nos.: US 7,199,314, Taiwan 279822, Pat. Pending in China)An optional momentary switch that is operational at all positions to allow excellent navigation and menu selection
-
product
Potentiometers
Accu-tach / Accu-dial
Programmable potentiometers with LCD display and feedback display in user units.• Replaces traditional potentiometers• Precise process control and feedback• Reduces costly downtime and product waste• Easy to install and calibrate• Tough ABS plastic enclosure - NEMA 4 rated• Small footprint - only 1.95" x 3.10"
-
product
X-Band Motion Detector
32213
The X-Band Motion Detector’s sensor is a common component in security systems and automatic door openers and can detect movements within a room, yard, or even on the other side of a wall. The X-Band Motion Detector operates in the X-band frequency, at 10.525 GHz and indicates detected movements with oscillations in its high/low output. Sensitivity is manually adjustable with a potentiometer, offering direct line of sight detection from roughly 8 to slightly over 30 ft (~2.4 to 9+ m).
