Filter Results By:
Products
Applications
Manufacturers
Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
- Pickering Interfaces Inc.
product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
product
Portable Electricity Meter Testers
EE-120A-3S
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
product
Portable Three-Phase Phantom Load
EE-120A-3 + EE-500V-3
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. The generated values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
product
Portable Three Phase Phantom Load Power Source
SY2103
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
product
Three Phase Phantom Load Test Bench
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
product
Phantom Load Test Set
Is a testing accessory, wisely designed for field testing service. This equipment helps in providing artificial load that is unaltered by the change in power supply.
-
product
Artificial Phantom Load with Power Factor
RC-50
The RC-50 Artificial Phantom Load has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges. Features: Artificial Load, Light Weight, 50 Amps, 50% Power Factor.
-
product
Desktop Meter Station
2100
The TESCO Desktop Meter Station is an extremely versatile piece of testing equipment. It can be used as a programming station, a single meter evaluation station, or a test bed for checking meter features and anomalies. The newly designed Meter Station not only has the ability to simply warm-up meters, but also has optional features such as an external load (1PH) or an internal phantom load (0.5A), an optional disconnect operation (1000VA XFMR), a load receptacle, or a tilt chassis. For easy operation, all options are conveniently mounted on the front panel.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
RC-50 Artificial Phantom Load with Power Factor
480
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
product
Portable Meter Test Kit
UTEC 430
The UTEC 430 is the first Portable Meter Test Kit to support both the Radian Dytronic (RD) and the installed base of Radian Metronic (RM) reference standards. The ability to support both reference standards makes the 430 the ideal budgetary solution for traditional on-site meter testing using Phantom Load current sourcing. Do not let its compactness fool you, the UTEC 430 has three 30 Amp current output elements for performing single-phase or three-phase meter testing. When each element is combined using the optional open link cable harness, the UTEC 430 can source up to 90 Amps.
-
product
Complete Field Meter Site Testing Solution
7 Series
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
product
Hand-held 3-Phase Meter Tester
3 Series
Powermetrix continues its industry leadership with the introduction of Powermetrix Remote Manager (PRM) for the PowerMaster® 3 Series. Powermetrix Remote Manager enables wireless control of essential and various metering site accuracy tests contained within PowerMaster® 3 Series from any Windows compliant system up to 100 feet in any environment, including high EMF environments! Customer load Meter Testing, CT/PT ratio testing, CT/PT burden measurement, meter register/demand testing, and wiring verification are all easily performed with this extremely portable, hand-held 3-phase power analyzer. In addition, with the new Model 335, phantom load meter testing and CT burden added testing are available to complete your field-testing needs.
-
product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Starting Current Test. Full analysis of the customer load can also be performed, if current clamps have been ordered. All test results ( maximum 3 Test Plans, 5 Manual Measurements and Customer Load Analysis) can be saved in one file. 100 saved files can be viewed on the LCD display or transferred to a PC via USB port.
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
-
product
Portable Electricity Meter Testers
EE-120A-1S
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
product
Load Module for SLSC
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
product
Load Board
cPCI Serial 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Phantom Pipeline Metal Detector
The Phantom IP69K certified Stainless Steel Pipeline system detects metal contamination in pumped liquids and pastes conveyed through its non-metallic pipe. The extra-rugged BSH casing enables the system to withstand the harshest production environments. Pipe material options include nylon, rubber, and Teflon wrapped pipe for higher pressure / temperature applications. The Diverter Valve reject system is typically used to divert contaminated product from the flow. A test ball insertion/retrieval kit is offered as an option with Pipeline systems, allowing for ease of manual testing.
-
product
Phantom In-Foil Metal Detector
The Phantom In-Foil Metal Detector is utilized to detect ferrous metals such as iron and steel in products packaged in foil. Available with BSH Extra-Rugged IP69K certified casing for the most resilient performance under harsh conditions such as washdown, the system is able to identify ferrous contaminants despite the presence of aluminum foil wrapping or trays.
-
product
Load Board
cPCI 6U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Electronic Loads
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
product
Test Loads
ML12
Each test load provides two test operations for verifying functionality of a Hipot Tester and Ground Continuity Tester. Provides two ground continuity tests (open and short) at up to 35 amperes maximum
-
product
Phantom Large Bag Metal Detector
The incomparable “Big Bag King” from Fortress sets an untouchable industry standard for sensitivity levels. No other system in the world can come close to detecting 2.0 mm stainless steel in 50-100 lb bags of dry product. The system also detects ferrous and non-ferrous metal as small as 1.5 mm. Traditionally, larger aperture sizes mean reduced sensitivity in the world of metal detection. However, the Phantom Large Bag system defies this law by using a specialized coil structure. It also includes a noise reduction modification that dramatically reduces the detector’s susceptibility to RF interference.
-
product
LOAD BOARD
The semiconductor manufacturing process is divided into a front process (WAFER) and a post process (PACKAGE). The LOAD BOARD is an INTERFACE device for inspecting the function and performance of a package state IC, which is a post process, It is an INTERFACE key device for inspection. In particular, LOAD BOARD is widely used in non-memory semiconductor inspection equipment.
-
product
Phantom Laboratory/QA Metal Detector
The portable and compact Phantom Laboratory Metal Detector is used offline to further examine rejected product from an in-line Large Bag or Gravity detection system. The Lab unit enables you to quickly filter out the metal contaminants and reclaim good product. Additionally, by isolating the contaminant QA can then determine the source of the problem and initiate corrective action. Equipped with a floor stand and castors, the Laboratory detector is easy to move from room-to-room. The ergonomically designed hopper offers a user-friendly means of hand-feeding product through its plastic pipe section. Two bins for Good product and Rejected product are also included with the system.
-
product
Terminations (Loads)
Loads find wide use as accessories for both broadband and narrowband measurement instruments. Keysight's family of fixed and sliding loads includes both general purpose grade loads as well as loads intended for use as calibration standards.
-
product
Load Cells
Whether you need general purpose, low profile or miniature cells for standard or special applications, you don't have to be an expert in force measurement, because we are. Talk to us about what sort of forces you need to measure, and under what conditions and constraints. We'll walk you through the load cell specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
Terminations & Loads
We have more than 40,000 rf & microwave coaxial terminations in stock we can ship today. We offer these Microwave & RF terminations: SMA Terminations, Type N terminations, 7/16 DIN terminations, 2.92mm terminations, 2.4mm terminations, TNC terminations, smp terminations, minismp terminations, 4.1/9.5 minidin terminations. 4.3/10 terminations, ssma terminations, ssmc terminations, and a few Reverse Polarity terminations. Power levels of 0.5-150 watts. RF / Microwave terminations are also known as dummy loads or 50 ohm dummy loads. Our 1.85mm terminations, are rated to 67ghz. We offer 1.0mm terminations good to 110Ghz.
