Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PXI/cPCI Modular Embedded Controller - PXI 2.0/PCIe 3.0 Compatible, Max 512MB DRAM (256MB Installed)
TE9500-1200
TSI's modular approach to PXI embedded controllers provides maximum flexibility and upgradeability for most, if not all, PXI embedded controller requirements. The TE9500 series of embedded controllers is based on the industry standard ETX (embedded technology extended) SOM (system-on-module) form factor. Whether you choose a power saving Celeron CPU or a high performance mobile Pentium III, the TE9500ís integrated interfaces and upgradeable options apply across all models of the TE9500 series of controllers. The TE9500 series gives you the ability to control your controller.
-
product
Boundary-Scan Test / In-System Programming Controller
CPXI-1149.1/Turbo
The CPXI-1149.1/Turbo is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the CPXI-1149.1/Turbo offers up to 80 MHz clock rates on 4, 8, or 32 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
-
product
ABex Terminal Module for JTAG Technologies JT 37x7 BSCAN Cards
ABex TM-JT37x7
The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
product
JTAG Live Controller
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
product
TAP Signal Isolation Module
JT 2139
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
product
JTAG Boundary-Scan Controller
NetUSB-1149.1/SE
8-TAP USB 2.0 and LAN Based JTAG Controller. The NetUSB-1149.1/SE is an advanced 8-TAP USB 2.0 and LAN-based JTAG/boundary-scan controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
JTAG Boundary-Scan Controller for PXI and PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37x7/PXI
High speed and performance JTAG Boundary-scan controller for PXI and PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
JTAG Boundary-Scan Controllers for High-Volume Production Systems
Corelis has designed special hardware that autonomously performs concurrent (gang) testing and programming of multiple units without additional user intervention. The entire testing and programming, including on-the-fly verification of results, is done in modular and expandable hardware.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
I/O Modules
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
Multiport JTAG Tester
XJQuad
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
-
product
Controllers
onTAP’s THREE TAP CONNECT JTAG
Connect the TAP CONNECT JTAG Controller to your application with either the Xilinx ribbon cable, flying leads, or Altera style adaptors. The onTAP TAP CONNECT Controller automatically senses and adjusts to target I/O voltages and interfaces to devices operating at 1.8 to 5.0 VDC for the standard controller, or 0.99 to 3.6 VDC for the low voltage controller, using the VREF voltage from the target chain. If there is no VREF available, you can set the voltage for the target application from the TAP CONNECT Controller. This facilitates easy configuration to many different JTAG ports, which is helpful in design and manufacturing.
-
product
ScanBridge
JT 2154
The JT 2154 is an experiment board based on National Semiconductor’s STA111 device, aimed at users looking to utilise addressable bridge/multiplexors within their designs, and thus set-up ‘system level’ JTAG access. The unit can also be used in semi-permanent installations to expand the TAP (Test Access Port) count on JTAG Technologies controllers in order to address highly segmented designs. Built-in support for ScanBridge-type devices within ProVision allows easy set-up of TAP assignments and device addressing.
-
product
CoreCommander
While many ICs are equipped with a JTAG (IEEE Std. 1149.1) boundary-scan register (BSR), a significant number of microprocessors and DSPs can be found with deficient or even non-existent BSRs. CoreCommander Micro uses the on-chip debug mode of processors to access ports and embedded peripheral controllers to promote ''kernel-centric'' testing. Similarly, in the case of today's Field Programmable Gate Arrays (FPGAs) test engineers can ''bridge'' from the JTAG interface to the resources of the gate array itself. Our CoreCommander FPGA product implements a translatorinterface that allows our JTAG hardware to control embedded IP cores via a variety of bus interfaces (e.g. Wishbone Avalon etc.).
-
product
PXI based Test Systems Module
PXI XJLink2
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
product
19" Rack Mount Chassis, Industrial JTAG-Powered PCB Tester-Programmer 'CombiSystem'
JT 57××/RMIC
The new-concept, industrial JTAG-powered PCB tester-programmer the JT 57xx/RMIc ‘CombiSystem’ comprises a sleek base-level 19″ rack-mount chassis assembly that can house up to four customer-specified modules chosen from various JTAG (IEEE 1149.x) controllers, digital IO and analog IO and other measurement modules.
-
product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
product
Production Stand-Alone
PSA
Using PSA, test engineers can build sequences of applications in the built-in AEX (Application EXecutive) manager using if then else goto capabilities. Sequence builders can also include additional capabilities through DOS/Win command line calls, create serial number logged test reports, export tests results to a database etc.. PSA includes drivers for all JTAG Technologies controller hardware past or present.
-
product
JTAG Functional Test
JFT
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
product
TAP Pods
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
Mixed Signal JTAG Tester
JT 5705
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
product
Remote Intelligent Pod
ScanTAP
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
product
Boundary-Scan Controller for PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37×7/PXIE
High speed and performance JTAG Boundary-scan controller for PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
product
PCI Based JTAG Controller
PCI-1149.1/Turbo
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
High-Speed USB 2.0 JTAG Controller
USB-1149.1/1E
The USB-1149.1/1E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/1E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
product
JTAG Probe
MAJIC
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
