Filter Results By:
Products
Applications
Manufacturers
Transient Generators
create sudden change of voltage, current, or load to test resilience to interference.
See Also: Impulse Generators
-
product
Transient Generators
9354-1 & 9354-2
The Model 9354-1 & 9354-2 Transient Generators were especially designed for the performance of a variety of pulse susceptibility tests on subsystems and/or equipment, in accordance with MIL-STD-461D and E, method CS116; also capable of testing for RTCA DO160D, section 22; MIL-STD-461C, methods CS10 and CS11.
-
product
Surge Generators
Hybrid
Surge pulses occur due to direct or indirect lightning strikes in a circuit or by switching transients caused by switching inductive loads or short circuits. This leads to currents or electromagnetic fields causing high voltage or current transients. Surge voltages and currents can reach several thousands of volts and thousands of amperes. Our following Surge generators simulate these disturbances for all the necessary level in accordance with IEC / EN 61000-4-5 and IEC / EN 60060.
-
product
Burst Simulators
EFTG
Our test generators simulate fast transient glitches as they are defined in the standard IEC / EN 61000-4-4. The individual pulses generate a wideband RF spectrum up to 300 MHz due to the very short rise time (5ns).
-
product
Electronic Loads
Flexible electronic DC loads for general purpose applications. Voltage up to 80V, current up to 80A and power up to 600 watts. CI, CR, CG, CV and CP modes, built-in transient generators. Models with USB, RS232, GPIB and LXI compliant LAN interfaces.
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
Power Discrete Tester
Mostrak-2
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
product
Transient Absorption
Our Transient absorption spectrometers use a powerful set of techniques used to identify electronic and structural characteristics of short-lived excited states (transient states) of photochemically/photophysically relevant molecules.
-
product
Transient Limiter
TBFL1
The TBFL1 is a combined transient limiter / attenuator / high pass filter, designed to provide optimum protection of spectrum analyzer or measurement receiver inputs when carrying out conducted noise measurements or other measurements where the input levels cannot be predicted with certainty or where accidental overloads may occur.
-
product
Transient Limiters
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
product
Transient Protection
GrayStone Automation is highly experienced in the field of transient & lightning protection having designed and manufactured products for Nokia, Times Microwave & PolyPhaser. Our expertise lays in developing and manufacturing products to protect data, telecommunication and rail system networks. Aside from the standard products we offer, we also work with customers to develop transient protection products for custom applications.
-
product
Generators
Radio Pulse Signal Generator
The Software Signal generator allows to to produce radio pulse signals of various pulse rate and frequency at the DAC output.
-
product
Generators
Frequency-Modulated Signal Generator
The Software Signal generator allows to produce frequency-modulated signals at the DAC output.
-
product
Generators
Pulse Signal Generator
The Software Signal generator allows to produce pulse signals with various pulse ratio and frequency at the DAC output.
-
product
Generators
Sinusoidal Vibration
Software application Sinusoidal vibration is used for testing products resistance to vibration impact at different frequencies and ranges. It is included into software complex ZETLAB VIBRO, supplied together with VCS ZET017-U. The program is available in VCS menu of ZETLAB control panel.
-
product
Generators
Classical Shock
Software Classical shock is used for testing specimen resistance to shock impact. As the Software Classical shock is activated, at the output of shaker control system ZET 017-U there is formed a signal with pre-set parameters. Types of signals generated:
-
product
Generators
OUR CHALLENGE“To drastically reduce the weight and size of Constant Potential X-Ray generator while maintaining first class performances”To successfully meet this challenge, our engineers have worked at designing an exceptional new X-Ray insert. This highly compact X-Ray tube combined with a revolutionary cooling system and a multiple output carrousel can definitely be considered to be the most versatile X-Ray generator ever developed. In addition, performances are not compromised in any way whatsoever.
-
product
Generators
Linear Frequency-Modulated Signal Generator
The Software Signal generator allows to produce frequency modulated signals with linear sweep at the DAC output.
-
product
Generators
Noise Generator
The noise type to be generated is to be selected from the context menu: right-click the section with the noise name and select the noise type you need.
-
product
Generators
Random Vibration
Random vibration Software program is used for testing the specimen resistance to random vibration impact. This program is a part of vibration controller ZET017-U.
-
product
Generators
Sine Signal Generator
The Software Sine generator allows to produce sine and constant voltage signals at the DAC output.
-
product
Generators
We offer a wide range of power supplies, current and voltage supplies, frequency references, RF generators, transceivers.
-
product
Generators
Signal Generator
Signal Generator is used for forming signals of various shapes, amplitude, and frequency at the output channels of ADC and DAC modules and FFT spectrum analyzers. Functionally, the Signal Generator software replaces stationary generators used in laboratories.
-
product
Generators
Vibration Shock
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
product
Generators
GE is bringing generator technology and performance to the next level. We engineer and build our generators to meet the demanding specifications that keep you on the leading edge of efficient, reliable output. Our equipment installs quickly, integrates easily, operates reliably and delivers more power. With over 12,000 generators shipped since 1901, GE understands your challenges, and offers a complete range of configurations and cooling technologies to meet industry needs.
-
product
Generators
Amplitude-Modulated Signal Generator
The Software Signal generator allows to produce amplitude-modulated signals at the DAC output.
-
-
product
Generators
Generating Signal From a File
The Software Signal generator allows to produce signals from binary and text files at the DAC output.
-
product
Generators
Saw-Tooth Signal Generator
The Software Signal generator allows to produce triangular and saw-tooth (descending, ascending) signals at the DAC output.
-
product
Surge and Transient Protection
Our surge and transient protectors are safety approved for instance for ATEx. The series cover both AC and DC instrumentation, and is retrofit, so already installed instrumentation can now use the extra high protection rate of up to 20 kA.
-
product
Trans-Guard Transient Protection
GrayStone Automation is highly experienced in the field of transient & lightning protection having designed and manufactured products for Nokia, Times Microwave & PolyPhaser. Our expertise lays in developing and manufacturing products to protect data, telecommunication and rail system networks. Aside from the standard products we offer, we also work with customers to develop transient protection products for custom applications.
