Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-D/10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
High Speed Data Acquisition Module
ADQ214
The ADQ 214 data acquisition card features dual channels, 14-bit resolution, 400 MSPS capture rate with 1.4 GHz analog input bandwidth, and a memory buff er of 64 MSample per channel. The combination of high speed, high resolution and wide bandwidth makes it ideal for broadband applications such as IF sampling of RF signals and high-speed data recording. PXI Express, USB interfaces.
-
product
High Speed Data Acquisition
Data acquisition (DAQ) is the measurement, recording, analyzing, and presentation of real world phenomena. It includes electrical measurements such as voltage, current, power as well as measurements through sensors and transducers including temperature, pressure, flow, level, strain, acceleration, vibration, humidity, and more.
-
product
IPTV Set-of-Box Auto Test System
IPTV Set-of-Box test system is general audio/video test system for IPTV RCA signal output. This system has these features: Based on high-speed, high resolution data acquisition board from National Instruments. It can support all video and audio parameters testing. High speed, 3x than traditional video analyzer and audio analyzer Cost down. Traditional video analyzer is expensive and difficult to adopt in factory pipeline Easy-of-use software interface
-
product
64 Channel 100 KHz 16 Bit ADC Module
DP-VXI-1101
DP-VXI-1101, the 16-bit, intelligent, 100KHz A / D converter module can be widely used in data acquisition applications requiring high speed scanning with 16-bit resolution and high accuracy of 0.01% of reading.The module occupies one slot in the VXI 'C' size mainframe.DP-VXI-1101 module uses 8 channel signal conditioner plug on modules(SCP) for accommodating various input signals. Eight such SCP modules can be plugged onto the main board to accommodate a maximum of 64 channels per A / D converter module.
-
product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
IPTV Set-Of-Box Auto Test System
Guangzhou Jumho Electric Co., Ltd.
IPTV Set-of-Box test system is general audio/video test system for IPTV RCA signal output. This system has these features: Based on high-speed, high resolution data acquisition board from National Instruments. It can support all video and audio parameters testing.High speed, 3x than traditional video analyzer and audio analyzer.
-
product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2220-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Integrated Conditioning, Acquisition & Control System
Series 6000
An innovative and fully integrated modular transducer conditioning, acquisition and control system, the Series 6000 has unparalleled performance and accuracy. From two to many thousands of channels, high & low speed, analog & digital, Series 6000 acquires measurement data from virtually all types of sensors and is fully customizable to fit the needs of any test facility. Large & small, AC & DC powered enclosures are available for nearly any test environment. Analog and digital I/O modules condition, amplify, filter and digitize signals from transducers. Turnkey and/or API software is available, helping facilities get up and running quickly.
-
product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
High Speed Digitizers
High performance and high speed digitizers with wide bandwidth and high dynamic range. Featuring high-speed Analog-to-Digital Converters (ADC) with Real-Time Field Programmable Gate Array (FPGA) based digital processors. Long acquisition memory coupled with fast PCIe offload and streaming over optical data interfaces (ODI).
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Data Acquisition Recorders & Loggers
B&K Precision offers a full range of data acquisition recorders & loggers for measuring parameters such as voltage, temperature, current, resistance, frequency, and pulse. From high speed recording with deep memory, to long battery life for portability.
-
product
PCIe 8 Bit High Speed Digitizer - 2.5 GH/s on 2 Channels, 1.5 GHz Bandwidth
M4I.2221-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
High Speed Data Acquisition Board
MS 1800
*Bus Interface:- 64 Bit PCI Bus with PMC Interface*Virtex-4 FPGA based design*32 channel digital I/O signal*RS232 & RS485 Interface*32MB Flash*2MB Static RAM for data storage*Analog Inputs:- 2 Channel*Input Resolution:- 14 Bits*Sampling rate up to 80MSPS*Filter:- Low Pass Filter for all channels*Two Analog Outputs*14 bit Resolution*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
Compact Measurement System For Steel Wire And Rods With Small Diameters
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
product
High Speed Data Acquisition
All systems can be set up in two types of aluminum chassis. These are the conduction cooled rugged 3U VPX chassis “Crosswind 600” and “Desert Gecko” . Ruggedized and sealed to IP65. These units can use void fillers and GORE brand vents depending on the deployment environment.
-
product
2-CH 14-Bit 200 MS/s High-Speed PXI Express Digitizer
PXIe-9852
The ADLINK PXIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PXIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference, the PXIe-9852 provides both high accuracy and high dynamic performance, making it ideal for applications requiring high-speed data acquisition, such as optical fiber and LIDAR testing, and video signal analysis.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Power Potentiostat/Galvanostat
1100C
The Model 1100B series power potentiostat/galvanostat is designed for electrochemical applications that require relatively large current and high compliance voltage, such as battery studies, corrosion, electrolysis, and electroplating. The current range is 2 A, and the compliance voltage is 25 V. The instrument contains a high speed digital function generator, a fast data acquisition system, filters for current signals, iR compensation circuitry, a potentiostat, and a galvanostat (Model 1140B). The potential control range is 10 V.
-
product
Data Acquisition & Analysis
Avionics Interface Technologies
We provide fully integrated avionics data bus and high speed network analyzer and data acquisition systems. Combining our extensive product catalog of Avionics interface modules, and our easy to use Analyzer software applications, with our Engineering Expertise, we are able to satisfy a wide range of avionics network data capture and analysis requirements with our COTS products or with customized solutions.
-
product
Logic Analyzer
Ant18e
The Ant18e logic analyzer is compact, easy to use, powerful, and inexpensive. The Ant18e features high speed data acquisition, state (synchronous) and timing (asynchronous) acquisition modes, Trigger-In and Trigger-Out connections, and a user-level programming interface.
-
product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2223-X4
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
product
Digitize, Quantify, Collaborate With Your Unique Automated Petrographic Microscope
ZEISS Axioscan 7 for Geology
Digitize your thin sections with Axioscan 7 – the reliable, reproducible way to create high quality, digitized petrography data in transmitted and reflected light. Uniquely designed for petrographic analysis, the Axioscan 7 Geo combines unique motorized polarization acquisition modes with unprecedented speed and a rich software ecosystem for visualization, analysis, and collaboration.
-
product
CPCI Integrated Communication Card
MS 3635I
CPCI Integrated Communication Card is high end Microprocessor based Mixed RS422 Communication and Differential Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have Synchronous RS422 Communication Interface, Asynchronous RS422 Communication Interface, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic storage and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
product
ScopeCorder
ScopeCorder product family provides flexible and high-performance multi-channel test instruments by combining the benefits of a mixed signal oscilloscope and traditional data acquisition recorder. The ScopeCorder delivers high signal fidelity and long term recording for both high speed transients and low speed trends to meet the most stringent measurement requirements.
-
product
YODA Profiler
The YODA profiler (“Yoing” Ocean Data Acquisition Profiler) is a “tow-yo” instrument to profile the water column with high spatial resolution from small boats without occupying much space. The instrument is provided with a deployment winch and sensors measuring conductivity, temperature, pressure, chlorophyll, turbidity and dissolved oxygen. The brush at the top of the instrument allows for a stabilizing effect on the free-fall sinking speed, which is approximately constant at 0.2 m/s. All data are stored internally and downloaded into a PC through a wet-connector and interface.
-
product
High Speed PCI Data Acquisition Processors
DAP 5400a
The DAP 5400a model, a board optimized for simultaneous sampling at extreme speeds, has eight A/D converters that sample simultaneously with 14-bit resolution at 1.25M samples per second each, for a total throughput of 10M samples per second. Or for higher speeds per channel, each board can sample each of 4 channels at 2M samples per second.
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.
-
product
Electrochemical Analyzer/Workstation
600E
The Model 600D series is designed for general purpose electrochemical measurements. The figure below shows the block diagram of the instrument. The system contains a fast digital function generator, high speed data acquisition circuitry, potentiostat, and a galvanostat (available only in select models).
