Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Battery Capacity Tester
BLU-A Series
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV moduleUp to three connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
product
Receiver Conformance Test Application for IEEE 802.3bm
M8091BMCA
IEEE 802.3bm Receiver Test Application for 25GAUI-1 Chip-to-Module, Chip-to-Chip, Cable and Backplane.
-
product
Ethernet Transformers
Pulse’s Ethernet transformers are RoHS compliant and qualified at major PHY suppliers. 100/1000/2.5G/5G/10GBASE-T Ethernet transformer modules are optimized for all major LAN transceivers. All modules provide electrical circuit isolation that meets IEEE 802.3, while maintaining signal integrity needed for the most demanding applications.
-
product
Bench Top Test Set
WesTest-3000/BTTS
WesTest Engineering Corporation
*PXI Based*Test Requirement Driven*Core Capability Consistency*Software Standards- ATML, IEEE
-
product
TSN/PTP Partner Test Tools
The following test and measurement tools are available for members within our IEEE 1588/PTP, Avnu, and TSN Testing services. We would like to thank all of our partner companies for allowing members the opportunity to test against their products in one lab. If you have additional testing needs please contact us today.
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
NetXpert XG2 10G Tester
#TXG200
*Ethernet Speed certification of copper and fiber optic systems up to 10Gb*Complete active network testing over copper, fiber and Wifi systems*Cable qualification to IEEE standards*TDR & fiber cable length measurement*PoE testing up to 90W (PoE++)
-
product
Special / Customer Spec. Crates
6U VME64x 6023 JLAB Crates
For the Thomas Jefferson National Accelerator Facility (JLAB) in Virginia (USA), a special version of the VME 6023 crate series with front to rear air-cooling was developed. “JLAB style” VME crates are available with standard VME/VME64 backplane and mechanics as well as with VME64x or VXS (see VXS section) backplane and IEEE 1101.10 compatible mechanics, (enhanced EMC and ESD shielding).
-
product
GPIB-RS232, Instrument Control Device - Taiwan 110VAC
779732-11
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
QualiPhyer Tools
QualiPhyer is a family of software packages used to test a product’s conformance to IEEE 802.3™ and MIPI Alliance electrical and optical standards for Ethernet and MIPI devices. These packages can be used to control oscilloscopes and traffic generators over Ethernet or GPIB connections to test the physical layer characteristics of devices. The software processes waveforms from the scopes to produce results based on algorithms developed at the UNH-IOL.
-
product
Reverse GPIB Cable Adapter
182768-01
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Male or Female GPIB (IEEE 488) Adapter - The GPIB Adapter connects GPIB cables to other accessories. NI offers it in Type XA, XE, and XF.
-
product
GPIB Bulkhead Adapter, Reverse entry
182767-01
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Female GPIB (IEEE 488) Bulkhead - The GPIB Bulkhead connects GPIB cables to other accessories. NI offers it in Type XC and XD.
-
product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Manufacturing Test Station
Scan Executive
The Scan ExecutiveTM Manufacturing Test Station is used to apply the same IEEE 1149.1 tests that were developed and used in the lab in a high-volume manufacturing environment without requiring additional development.
-
product
Portable High-Voltage VLF Test System
VLF-60
The system is designed for VLF (0.1 Hz) withstand testing of cross-linked polyethylene (XLPE) insulated cables.Integrated Tan Delta (tan δ) measurement module allows to evaluate the general condition of cable insulation according to IEEE 400.2-2013 international standard.
-
product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,2 m
763061-02
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
Battery Capacity Tester
BLU-C Series
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
product
New Line of Frequency Synthesizers (Insight FS) from 36 to 1250 GHz
In the millimeter wave range, each synthesizer covers a full waveguide band (Q, U, V, E, W, F, D, G, Y, J). Insight FS provides several options for frequency and amplitude modulation (analog FM/AM modulation, frequency manipulation, pulses modulation). Insight FS are compact in size and controlled by IEEE, analog input, or manually.
-
product
STDETransformer Demagnetizer
STDE
This option allows neutralizing the residual magnetization of the power transformer core after the winding resistance test. The principle of the option is to apply a constant current of alternate polarities to the transformer winding, as per the IEEE 0062 1995 standard.
-
product
Primus Epic Interface Kit
LANTAP-10
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
product
High-Speed Networking And Video Products
We offer a variety of solutions to support the development of embedded systems using a variety of high-speed networking and video technologies, including ARCNET, CoaXPress®, DisplayPort, Ethernet, HD-SDI, IEEE® 1394b (FireWire), MOST®, Optical Transport Network (OTN), Synchronous Optical Networking/Synchronous Digital Hierarchy (SONET/SDH), T1/E1 and Fiber-to-the-Home/Passive Optical Network (FTTH/PON) protocols.
-
product
PD Conformance Test Suite
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
product
CPU Debugger
Green Hills Probe V4
The Green Hills Probe is an advanced hardware debug device that connects to the onboard debug ports present on most modern microprocessors, such as IEEE 1149.1 JTAG and BDM. With support for more than one thousand devices from over thirty manufacturers, a flexible electrical interface, and out-of-the-box support for the largest multicore systems, the Green Hills Probe provides fast, reliable debugging, programming, and system visibility to projects present and future.
