Filter Results By:
Products
Applications
Manufacturers
Noise Figure
delta of UUT noise to ideal.
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
product
NBS-Series Cryogenic Primary Noise Standards
The NBS-Series provide the ultimate accuracy when measuring extremely low noise figures (noise temperatures).
-
product
Seismometers
3T-120 Pothole
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
product
Fixed/Dual Delay Line
Series 1000
The EOX Series 1000 RF/Microwave Time Delay System is an economical, high performance, turnkey solution for radar test, wireless communications, Wi-MAX, and altimeter applications. The Series 1000 features ultra wide bandwidth, low loss, high isolation, low noise figure, and high dynamic range. Available with time delays up to 250 µsec and a top end frequency of 18 GHz.
-
product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
product
VXT PXIe Vector Transceiver
M9421A
Purpose-built for rapid solution creation and faster throughput in manufacturing test of wireless components, power amplifiers, and RF front-end modules Increase test density and reduce your footprint with up to four VXT instruments in one 18-slot chassis Reduce development time with open-source test libraries and reference solutions Start closer to your finish line with built-in FPGA-accelerated measurements Optimize test routines using proven software for noise figure and standard-specific measurements
-
product
PCI Express Receiver Board
AD12-2000-IRIGB
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
product
Frequency Block Converter
FBC
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
product
Noise Figure Measurements With Vector Correction
S93029B
The S93029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers, utilizing Keysight’s unique vector-source-correction technique
-
product
Analog RF Slot Downconverter: 1700-2100 MHz Input
Model 8111-004
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
product
Low Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
product
Noise Source Family
347
The R347B waveguide noise source cover the R-band (26.5 to 40 GHz frequency range), while the Q347B model cover the Q-band (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices.
-
product
5G Switch LNA Modules
Macom Technology Solutions Holdings Inc.
MACOM offers a complete portfolio of high-power switch and LNA modules to cover many sizes and classes of 5G base stations, including Macro Cell, Small Cell, and massive-MIMO AAS in frequency bands up to 6GHz. SOI-based switch modules with up to 20W LTE power handling are extensively used in mMIMO and Small Cell radios, and MACOM proprietary PIN diode Switch modules with up to 160W LTE power handling are widely deployed in Macro radios. Featuring ultra-broadband, low noise figure and excellent power handling and reliability, the family of Switch LNA modules are also well suited for a variety of TDD based communication systems in commercial and military applications.
-
product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
product
Low Noise Amplifier
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
product
UP Converter
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
product
Real-Time Spectrum Analyzers (RTSA)
Gain more confidence in your system or signal environment knowing you can capture intermittent or transient signals as short as 3.57 µsMaximize your investment when you add real-time capabilities to a UXA, PXA or MXA X-Series analyzer -no need for a dedicated instrumentGo deeper and thoroughly analyze complex signals with the 89600 VSA softwareAccelerate communication system development by quickly switching to must-have traditional measurements like phase noise, noise figure, and more
-
product
LNA, Millimeter-wave Power Amplifier And Rack Mount Amplifier
Panda Microwave design up to 50GHz broadband power amplifier, including LNA, CW and pulse medium, Rack Mount Amplifier and millimeter-wave high power amplifier. Our amplifiers cover frequency range from 100MHz to 50GHz and use Thin-film Technology. Low noise amplifier have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifier system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
Broadband Power Amplifier
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
Microwave System Amplifier, 2 GHz to 26.5 GHZ
83018A
The Keysight 83018A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 2 to 26.5 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies. The standard Keysight 83018A includes internal directional detectors for external leveling applications. With excellent noise figure relative to its broad bandwidth and high gain, this amplifier significantly improves system noise figure and dynamic range. The Keysight 83018A comes equipped with a low profile heat sink, an integral mounting bracket, and a two-meter dc power supply cable. Thermal characteristics and power supply design allow fast, easy integration into most measurement systems.
-
product
RF Front-End ICs
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
product
Low Noise Amplifier
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
product
Low Noise Amplifiers
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's low noise amplifiers typically exhibit noise figures below 5.5dB and output 1dB compression points up 8dBm. These amplifiers are economical choices for general purpose applications. KeyLink's low noise amplifiers can be categorized as follows.
-
product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
product
Low Noise Super Wide Band Amplifiers
WBA Series
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
product
Bi-Directional Amplifier
Integrated dual directional amplifier offering high output power and low noise figure
-
product
Noise Source Family
SNS Series
Works in conjunction with the NFA Series of noise figure analyzers to simplify measurement set-up and improve accuracy and reliability, automatically downloading electronically stored calibration data.
