Filter Results By:
Products
Applications
Manufacturers
- Advanced Telemetrics International
product
Flex-plate Torque Sensing Systems
Advanced Telemetrics International
ATi’s FlexPlate Torque Sensing Systems permit in-vehicle Engine Output torque measurements.
-
product
40 Amp Intelligent Power Management
IPMDS40
- Intelligent Power Management System- 9 - 20 Amp Single Outlets- Automatic Single Phase Load Balancing- Automatic Load Shedding based on priority rating- 40 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
product
Circuit Breaker Analyzer
CBA 2000
CBA 2000 diagnostic system is designed to grant the highest accuracy while testing circuit breaker. It can perform static and dynamic contact resistance measurement and it’s a precise timing speed and motion analyzer. Circuit breaker timing test set CBA 2000 is the perfect solution when a complete and reliable diagnostics has to be performed on circuit breakers.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Loop / PFC Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Switchgear Testing Solutions
IES Systems is a world leader in the design and manufacturing of power switchgear test systems.*GFCI/AFCI Circuit Breaker Test Solutions*Medium Voltage Breaker Test Solutions*Residential Circuit Breaker Test Solutions*Molded Case Circuit Breaker Test Solutions*AIR Circuit Breaker Test Solutions*Vacuum Bottle Test Solutions
-
product
Circuit Breaker Test System
TDR900
The TDR900 is your entry-level portable circuit breaker test set.It operates and records a circuit breaker's contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.Use the TDR900 to verify control circuit, check motion of moving parts, validate time of operation and demonstrate results of circuit breaker maintenance.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Circuit Breaker Test Systems
Crest has over a decade of experience of designing and manufacturing test systems for testing all the different kinds of switchgear and controlgear.
-
product
Circuit Breaker Test System
TDR9100
The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.
-
product
Stationary Circuit Breaker Testing
ACTAS L260
High-precision test system for function tests on various types of switchgear device, including circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit.The inputs and outputs are connected flexibly via a terminal strip, making the test system particularly suitable for use in development and laboratory environments as well as in production environments.
-
product
3 Wire (Analogue) Earth Resistance Tester
2705 ER
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
product
Stationary Circuit Breaker Test System
ACTAS C160
Stationary test system for carrying out fully automatic final factory tests, type and function tests on all kinds of switchgear devices, such as circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit. All the electrical and mechanical parameters needed for the assessment of switching performance are measured in real time and evaluated without either the main contact chambers or the drive unit having to be opened. The system has analog and incremental input channels for the acquisition of analog quantities.
-
product
Coil Analyzers & Power Supplies
Coil analyzers and power supply units are portable and lightweight devices intended for use in harsh switchyard and industrial environments. The typical application is switchgear and circuit breaker testing when substation battery is not connected or available. An advantage over substation battery is enabled testing in under-voltage and over-voltage conditions. Furthermore, the stable voltage outputs with a very low ripple (<0,5%) enable an analysis of the coil and motor current graphs recorded with circuit breaker analyzers from different vendors.SAT40AD, POB30AD, and POB40AD are unique devices in the market due to their dual purpose:Power supply for coils and spring-charging motorsTesting circuit breaker’s coils, motor, and auxiliary circuitAll DV Power coil analyzers and power supply units have four separate outputs for opening and closing coils.SAT40AD has two powerful motor outputs (AC and DC) which can withstand up to 40 A inrush current.POB30AD and POB40AD have DC motor output rated up to 30 A and 40 A respectively. With the use of motor outputs, POB and SAT can also be used as a power source or a temporary battery charger.SAT40A II series instruments can be controlled via PC. The DV-Win application software is used to control both SAT and CAT (Circuit Breaker Analyzers & Timers) devices at the same time, making a unique test system for switchgear and circuit breaker testing.
-
product
3 Wire (Digital) Earth Resistance Tester
2720 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
product
Switchgear Test Systems / Circuit Breaker Testing
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
product
3 Wire (Digital) Earth Resistance Tester
2120 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
product
3 Wire (Analogue) Earth Resistance Tester
2105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
Adjustable Test Stab Set
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
product
ELM Electronic Load Module
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
product
Automatic Circuit Breaker Test Systems
UPA-16 (UPA-20)
Mobile systems for primary injection testing and trip curve control of circuit breakers and overcurrent protection relays.
-
product
3 Wire (Digital) Earth Resistance Tester
4120 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
product
Insulation & Multifunction Tester (LCD Display)
4167 MF
Standard Electric Works Co., Ltd
● High Quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Two insulation test voltages(DC) : 250V and 500V.● Alternation voltage measurement.● Battery life indicator.● Fuse protected.
-
product
Circuit Breaker Testing Equipment
CB SCOPE
SCOPE introduces CB SCOPE – Loco Vaccum Circuit Breaker Test System; the ultimate solution for testing Loco Circuit Breakers of all types. CB SCOPE is the most complete analyzer for checking the dynamic performance of LOCO VCB’s.
-
product
Resistance Measurement
PROMET
High-precision micro-ohm measuring systems with adjustable DC test current for determining resistances on circuit breakers or inductive loads such as transformers, for example. The high-precision ohm meters of the PROMET series are used to determine very low electrical resistances in the µΩ range. The adjustable test current of up to 600 A in combination with a four-wire measuring method delivers measurement results which meet stringent accuracy requirements. State-of-the-art power electronics coupled with a robust design guarantee excellent reliability for use as a portable device in switching stations and industrial environments. Typical applications include determining the contact resistance of switchgear devices and determining the resistance on inductive loads such as transformers.
-
product
Circuit Breaker Test System
TDR9100
The Doble TDR9100 is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.The TDR9100 provides main contact timing, motion, resistance and capacitance measurements with the flexibility to double or triple your usable channels.Use this inclusive, rugged and field-portable instrument for simple and complex testing of circuit breakers.
-
product
3 Wire (Analogue) Earth Resistance Tester
1105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
3 Wire (Digital) Earth Resistance Tester
1120 ER
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
product
Circuit Breaker Testing
HAOMAI Electric Test Equipment Co., Ltd.
Circuit Breaker Testing is utilised to test the operation of each switching systems and the programming of the entire tripping structure.
-
product
Circuit Breaker Test System
AutoScan
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
product
Primary Test Manager
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
