Filter Results By:
Products
Applications
Manufacturers
- InterWorking Labs, Inc.
product
Network Emulator
KMAX
The KMAX network emulator helps network engineers test and measure performance in order to identify and remove defects. Network emulators turn well behaved development and test networks into the kind of slow, congested, and less-than-reliable services encountered on the internet. In addition, unlike the real internet, network emulators allow the operator to control these conditions so that products and apps can be subjected to controlled and repeatable tests, by routing selected packets through a series of impairment nodes.
-
product
Copper Network TAPs
Network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers copper network TAPs in network speeds of 10/100M or 10M/100M/1000M (1G). Copper TAPs are purpose-built hardware devices used for out-of-band monitoring tools and make a 100% copy of your networks data allowing your monitoring tools to see every bit, byte and packet.®
-
product
Duty Cycle Meter
Displays ON or OFF period as a percentage of total period over a programmed gate time from 10 ms to 199.99 s. A resolution of 1%, 0.1% or 0.01% is user-selectable. Applications include monitoring modulated proportional control systems and pulse-modulated systems, such as radar, lasers or packet radio.
-
product
WAN Simulator / Emulator
LANforge ICE
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
product
Interface
RCNIC-A2PA-TB
The RCNIC platform is a high performance Thunderbolt 3 device for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
Advanced Aggregators
Aggregators are devices designed to increase efficiency and port utilization of network packet brokers. They are commonly used at the network edge or in TOR applications where port utilization tends to be low. Aggregators are also capable of pre-filtering traffic prior to sending out to Network Packet Broker’s for advanced filtering or taking the place of packet brokers in applications where only L2-L4 filtering is required. Aggregators improve ROI by reducing the total cost of a network visibility fabric and increasing the efficiency of existing infrastructure.
-
product
CN67XX Packet Processor, PrAMC Based
AMC735
The AMC735 is a 10-Gigabit Ethernet (10GbE) AdvancedMCTM (AMC) module which includes an on-board line rate multi-core packet processor based on Cavium CN67XX CPU. VadaTech offers this product in a mid size (full size optional) form factor compliant to the AMC.1 and AMC.2 specification, the AMC735 is based around the Cavium OCTEON CN67xx processor which has been specifically designed to intelligently process Ethernet packets at line-rate. The number of processor cores, speed grade, and amount of DDR3 memory is customizable based on customer needs.
-
product
VOIP
Macom Technology Solutions Holdings Inc.
MACOM’s family of VoIP processing devices, in concert with carrier-grade media stream processing software, delivers a complete, integrated VoIP media, data and fax, signaling and control processing solution. Combined with dual-core ARMs, powerful DSP cores, dual Gigabit Ethernet with flexible packet processing engine and a rich set of interfaces, the processors support 8 to 160 channels of packet-TDM and packet-packet operations, with an integrated host controller supporting control, signaling and other application specific functions. Major applications include next-generation network (NGN) POTS/ISDN line cards focused on class 5 replacement, xPON MDUs, IP-DSLAMS, MSAN, and IP-PBX, and Unified Communications.
-
product
Functional Testing for Evolved Packet Core (ePC/VePC)
PacketCraft
is a software-only functional tester for ePC and VePC networks. It is installed on a customer laptop or desktop, or on a virtual PC in the cloud.
-
product
Media Gateway
A Media Gateway is a networking device that provides valuable and essential functions for organizations, service providers, and network operators. When interconnecting traditional time-division-multiplexed (TDM) telephony systems with modern voice-over-internet protocol (VoIP) systems, a VoIP media gateway works by providing protocol conversion (translation) and interoperability between the two network technologies. Also known as an IP media gateway or SIP media gateway, the device converts a traditional analog plain-old-telephone-system (POTS) voice signal or related digital telephony signals such as T1, DS3, STM1 or OC3 into packets for transmission over a data network such as the Internet, private IP Network or a corporate LAN. When the legacy system is based on digital integrated services digital network (ISDN) technology, the device may be called a digital VoIP gateway or ISDN media gateway. Some manufacturers combine gateway functionality with WAN-access (internet-access) capability into a single device or network appliance. Such a dual-purpose device may be known as an access media gateway.
-
product
Network Emulation 100GE, 50GE, 40GE, 25GE, 10GE
Chimera by Xena is a network impairment emulator that makes it easy to introduce consistent, accurate, well-defined and repeatable impairments (e.g. packet manipulation, latency, jitter, bandwidth control and shaping) to traffic between DUTs in the lab. All rates from 10GE to 100GE are supported by a single 2-slot test module.
-
product
OTN: Framer/Mapper/FEC
Macom Technology Solutions Holdings Inc.
MACOM’s OTN Framer/Mapper/FEC family products offer complete portfolio of solutions for 10G, 40G and 100G optical transport networks. They are ideal for high-capacity Carrier Ethernet router/switches, Packet Optical Transport systems and DWDM Transport systems. The OTN framer devices integrate high performance Serdes I/O to allow seamless connection to optical and copper modules. The provisional Tri-FEC integration supports G.709 standard RS-FEC as well as high coding gain G.975.1 I.4 EFEC and I.7 UFEC to improve optical link performance, achieve longer reach and offer interoperability flexibility.
-
product
Gigabit Ethernet Tester Module for 1G and 10G Packet
GAO-ENET-103
GAOTek Gigabit Ethernet Tester Module for 1G and 10G Packet is designed for installation and maintenance of Metro/Carrier Ethernet and IP services. It supplies a compact test solution for 1G and 10G packet Ethernet, including ITU-T Y.1564 standard for SLA and OAM test features.
-
product
Network Security Scanner
Nmap ("Network Mapper") is a free and open source (license) utility for network discovery and security auditing. Many systems and network administrators also find it useful for tasks such as network inventory, managing service upgrade schedules, and monitoring host or service uptime. Nmap uses raw IP packets in novel ways to determine what hosts are available on the network, what services (application name and version) those hosts are offering, what operating systems (and OS versions) they are running, what type of packet filters/firewalls are in use, and dozens of other characteristics. It was designed to rapidly scan large networks, but works fine against single hosts. Nmap runs on all major computer operating systems, and official binary packages are available for Linux, Windows, and Mac OS X. In addition to the classic command-line Nmap executable, the Nmap suite includes an advanced GUI and results viewer (Zenmap), a flexible data transfer, redirection, and debugging tool (Ncat), a utility for comparing scan results (Ndiff), and a packet generation and response analysis tool
-
product
HPx-346 Analogue to Network Radar Converter
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
product
Global Network Monitoring and Incident Response
NetOmni™
NIKSUN NetOmni™ collects information (e.g., Logs, NetFlow, SNMP, Packets, etc) from all network applications, services, and their underlying infrastructure and prioritizes key service delivery, security, and compliance metrics. This enables powerful correlated dashboards and workflows from a single pane of glass.
-
product
Garland vTAP
With organizations becoming increasingly dependent on virtual computing, IT professionals need a solution to eliminate the blind spots inherent to virtual environments. Garland's vTAP is a software solution to address these challenges by providing complete visibility for east-west and inter-VM traffic. When used alongside Garland's physical TAPs, IT teams will have full confidence they are seeing every bit, byte, and packet® across their network.
-
product
Enterprise Voice & Data Processors
Macom Technology Solutions Holdings Inc.
Macom offers a line of infrastructure voice processors, in concert with the carrier-grade Media Stream Processing software, that delivers complete, integrated VoIP media, data and fax, signaling and control processing solution. Combined with powerful DSP cores with flexible packet processing engine and a rich set of interfaces, the processors support 8 to 32 channels of packet-TDM and packet-packet operation across the entire range of IP modulations, for VoIP and Data applications. Major applications include Enterprise voice gateway PBX, Enterprise class WAN router, Firewall, VPN routers, high speed 802.11 access point, integrated access device, packet voice enabled IP router, IP enabled PBX.
-
product
Cable Modem Test Platform
Promptlink Communications, Inc.
CMTP has broad support for the mixed environment of DOCSIS 3.0, and earlier devices. Similarly, it supports all DOCSIS/Euro DOCSIS equipment vendors, impartially treating each vendor's devices with maximum performance and minimum hassle.CMTP is fully automated, requiring no user input for testing.CMTP tests the basic Cable Modem, Wi-Fi and EMTA parameters such as signal levels, signal to noise ratio, etc. as well as device throughput and packet loss. For PacketCable devices, CMTP tests each phone port individually, with maximum functionality being tested.CMTP can also be configured to upgrade the firmware of the devices in a multi-step and conditional process.
-
product
LAN (PoE) Expansion Kit (supporting Gbit Ethernet)
OP-SB89G
OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate.
-
product
1000BASE-T1 Ethernet Logging Expansion With Low Latency
PT-20MG
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
product
HTTP Sniffer
EffeTech HTTP Sniffer is a HTTP packet sniffer, protocol analyzer and file reassembly software based on windows platform. Unlike most other sniffers, it is dedicated to capture IP packets containing HTTP protocol, rebuild the HTTP sessions, and reassemble files sent through HTTP protocol. Its smart real-time analyzer enables on-the-fly content viewing while capture, analyze, parse and decode HTTP protocol.
-
product
Network Emulator Software
NetDisturb
NetDisturb allows disturbing flows over IP networks helping to study the behavior of applications, devices or services in a “disturbed” network environment. NetDisturb is inserted between two Ethernet segments acting as a bridge and operates bi-directional packet transfer on Ethernet, Fast Ethernet and Gigabit network interface cards.
-
product
network analyzer
Capsa Free
Capsa Free is a must-have freeware network analyzer and packet sniffer for Ethernet monitoring, troubleshooting and analysis. Capsa Free is a perfect choice for students, teachers and computer geeks to learn protocols and networking technology knowledge. The Capsa Free freeware application by Colasoft is one of the most popular free packet sniffer products available.
-
product
Network Protocol Analyzer
Wireshark
Wireshark is the world''s foremost network protocol analyzer. It lets you see what''s happening on your network at a microscopic level. It is the de facto (and often de jure) standard across many industries and educational institutions. Deep inspection of hundreds of protocols, with more being added all the time. Live capture and offline analysis. Standard three-pane packet browser. Multi-platform: Runs on Windows, Linux, macOS, Solaris, FreeBSD, NetBSD, and many others. Captured network data can be browsed via a GUI, or via the TTY-mode TShark utility.
-
product
2-port 25GbE SFP28 LAN Module With Intel® XXV710 Ethernet Controller
AX93332
The AX93332 is a dual-port 25 GbE SFP28 module with Intel® XXV710 Ethernet controller. This module offers excellent packet performance for virtualized features, providing advanced features including VMDq, SR-IOV and DPDK to deliver amazing performance. It is designed to support demanding workloads for enterprise, cloud, and data centers.
-
product
Desktop Network Appliance Platform With Intel® Atom® Processor C3338/C3558/C3758 And Up To 10 LANs
NA362
The NA362 is powered by the low power consumption Intel® Atom™ processor C3338/C3558/C3758 (Codename: Denverton). In addition to six 10/100/1000 Mbps LAN ports (Intel® i210 Ethernet controller), this desktop network appliance also comes with four 10 GbE SFP+ fiber ports for high bandwidth and long-distance communications. The NA362 is an excellent choice for a wide array of network applications including UTM, VPN, firewall, gateway, SD-WAN and vCPE with its enhanced security and performance. The Denverton–based NA362 features the Intel® QuickAssist Technology (Intel® QAT) for accelerated data processing including symmetric encryption and authentication, asymmetric encryption, digital signatures, RSA, DH, ECC, and lossless data compression. Furthermore, it also supports the Intel® Data Plane Development Kit (Intel® DPDK), which greatly boosts packet processing performance and throughput, allowing more time for data plane applications. The NA362 comes with either two or four DDR4 R-DIMM/U-DIMM with 64GB or 128GB of non-buffer non-ECC/ECC memory. The slim-type network communication platform is equipped with one 2.5" SATA3 HDD and one mSATA for sufficient storage. It also supports wireless communication of Wi-Fi, 3G, LTE through a PCI Express Mini Card slot. I/O options include two USB 2.0 ports and a serial console port. To ensure reliable operation, the 10-port network platform supports watchdog timer. Moreover, it also supports mainstream Yocto, Linux, Windows® Server 2012 R2, and Windows® Server 2016 operating systems.
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
Advanced Ethernet Tester
LinkRunner® 10G
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
product
DMX Tester Portable
DTR-HH
The DTR-HH is a DMX 512 tester data send / receive unit with 10 store and recall preset scene snapshots. Each of the 10 presets will store 512 channel levels including the packet size and start code. Each preset can be edited to precise values and recalled anytime.
-
product
DVB-T2 Gateway module
T2Gateway
T2Gateway for HDc is ENENSYS’ DVB-T2 Gateway module (T2-base or T2-lite) that encapsulates one or several MPEG-2 Transport Streams into a DVB-T2 multiplex, inserts synchronization data for single frequency network broadcasting, allocates data into the different physical layer pipes and generates T2-MI packets over ASI and IP.
