Cable Fault Locators
Use time domain reflectometry to locate signal loss or a Murray loop bridge.
See Also: Cable TDR, Cable Sheath
- Pickering Interfaces Inc.
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 0.5m
A020GMR-C-1B050
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Visual Fault Locators
*Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap.*Fiber visual fault locator is a kind of device which is able to locate the breakpoint, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional ...show more -
product
Underground Cable Fault Locators
Techno Instrumentation (India) Private Limited
Complete range of underground cable fault locators. Manufactured in India.Surge GeneratorsReflectometer(Pre-locator) - Cable fault distance locatorCable fault finder/pinpointerHigh Voltage Murray LoopDC high voltage testersCable fault locating van
-
product
Cable Fault Locators
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circ...show more -
product
Cable Fault Locators
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
product
Signal Acquisition and Filtering Technology
SNAPTrack®
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequenc...show more -
product
Power Cable Fault Locators
We're professional power cable fault locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality power cable fault locator from our factory. All our portable products used in utility locations are with CE certification.
-
product
Cable Fault Locators
Wuhan Sunma Technology Co., Ltd.
Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap. Fiber visual fault locator is a kind of device which is able to locate the break-point, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional ...show more -
product
Cable Route Tracing and Identification
Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.
-
product
CATV Meters & Instruments
GAOTek offers high quality, affordable CATV meters and testers to industry engineers. These instruments are used by professionals to automatically or manually test, measure, and maintain a wide collection of systems and channels. Our products are portable and durable to ensure long operational use during everyday field use by CATV technicians. Additionally, we offer QAM analyzers, PCM channel analyzers and TDR cable fault locators.
-
product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-112
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI Dual Bus 32-Chan 2A Fault Insert Switch, N/O Through Relays
40-190B-502
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI 10A Fault Insertion Switch 10-Chan 1-Bus
40-199-001
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
product
48-Ch 2A-250VAC 2-Bus Fault Insertion
YAV90076
48 channels2A 250V 2 Fault Insertion BusesSwitching up to 60CAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-012
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-193A-001-HI
The 40-193A-001-HI is a 7-Channel Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
PXI 34-Channel 4-Bus 2A Fault Insertion Switch
40-197A-001
This 34-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers. A low cost 16-channel option is also available.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
68-Pin SCSI-II Female to 68-Pin SCSI-II Female, D-Type Shielded, 1m, Multifunction Cable
185262-01
68-Pin SCSI-II Female to 68-Pin SCSI-II Female, D-Type Shielded Multifunction Cable - The SH68-68-S connects compatible multifunction I/O devices to accessories or cables with SCSI-II connectors. 1m.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks)
A200LMR-200LFR-6B100
This male to female 1m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by male screwlocks.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-FU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Cut Ends, 2m
A009DM5-C-0A200
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Cable Assembly 44-Pin D-Type Female to Unterminated With Cut Ends, 1m
A044HF4-C-0A100
The 44-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to the product by screwlocks.