Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Software Development Kit
InterNav®
Open architecture software with interface source code and analysis tools for integrating GPS, inertial, and other aiding sensors on a VxWorks, Linux, or Windows computer.
-
product
Circuit Design Tool
SA-Designer lets you design actual analog front-end circuits employing Smart Analog products (Note1) and then generates the circuit data as C source code.
-
product
Intelligent Interface Card
IIB-1553-MMA
The IIB-1553-MMA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the M-Module standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-MMA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, withcomprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
PCI Direct Digital Synthesizers
SYNTH300 SERIES
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
product
MIL-STD-1553 MCH
M4K1553MCH
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
Code Repository Software
Helix TeamHub
Your code repository software is where you store your source code. This might be a Mercurial, Git, or SVN repository. Helix TeamHub can host your source code repository, whether it’s Mercurial, Git, or SVN. You can add multiple repositories in one project — or create a separate project for each repository.
-
product
Single Slot Intelligent Interface Card
IIB-3910-CPCI
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided in BC and RTs modes, with full error detection in BC, RT, BM and CBM modes. Dual redundant 3838 interface, with user selectable dual redundant optical or single redundant electrical 3910 interface are featured. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Time Code Generators
Masterclock's time code generators provide a source of very stable time code and accurate time and date information. The GPS500 extracts timing reference from GPS satellite signals and generate time code synchronized to within less than 10 microseconds of UTC (Universal Coordinated Time). It can output IRIG-B with and without IEEE 1344 date encoding, SMPTE/EBU, NMEA 0183, Kinemetrics/Truetime, and 1PPS.
-
product
Becker Transponder Test Fixture
TA-3400
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
product
Software Tools for Efficient Code Development and Analysis
Specador Documentation Generator
Specador is a tool that automatically generates accurate HTML documentation from comments inserted in the source code. It works in batch mode (command line) and uses dedicated language parsers.
-
product
Formally Verified Optimizing C Compiler
CompCert
AbsInt Angewandte Informatik GmbH
Meet the highest levels of software assurance by compiling your application with the only C compiler that's been formally verified to be free of miscompilation issues. All safety properties verified on the source code, e.g. with Astre, are guaranteed to hold for the generated executable as well.
-
product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
product
FRAMOS SLVS-EC RX IP CORE
Sony’s SLVS-EC interface standard has emerged as the best high speed interface to Sony’s best image sensors, enabling higher throughput, greater signal integrity, and simpler designs. Engineers developing solutions using Xilinx FPGAs and SoCs can take advantage of FRAMOS’s SLVS-EC RX IP Core, Evaluation Board and tested source code examples. Device builders and camera vendors can de-risk the design while reaping the benefits of Sony’s latest high-speed interface.
-
product
Coverage Analysis
VerOCode
VerOCode can use the same requirements-based tests that were used in functional testing to automate the capture and analysis of structural coverage testing without instrumenting the code under test. This is part of the process used at Verocel. It then records and displays the instructions executed in a program under test, and for conditional instructions, records and displays the state of the condition code at each execution of the instruction. Structural coverage is obtained at the machine code level using the integrated image, with results reported through an annotated program listing containing the source and machine code level expansion
-
product
IRIG Timecode Receiver and Generator
RG1
The RG1 Time Code receiver synchronizes to IRIG-A/B/G time codes and provides precise time in a memory register, for the host SBC.The IRIG output of the card can be used to synchronize other IRIG time code readers. Additionally, the RG1 includes a real-time clock (RTC) that may be used as a reference source for IRIG master applications, to free the system processor from the task of updating the master timer.
-
product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
product
Portable Electrical Management Systems
EMS-PT30C
Progressive Industries Portable Electrical Management Systems (EMS) offer quick and easy RV electrical protection. A true plug-and-play application with no installation required. You will feel secure with multi-mode surge, voltage, polarity, and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: voltage(s), current frequency, error code, and previous error code (if applicable). Additionally, the computer is driven by state of the art microprocessors.
-
product
Enhanced Serial Interface Module for Excalibur 8000 Family of Carrier Boards, with High Baud Rate & High Throughput
M8KSerial
The M8KSerial is an enhanced serial interface module for the multiprotocol Excalibur 8000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to two independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M8KSerial module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 8000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M8KSerial module is supplied with C drivers, including source code.
-
product
Intelligent Interface Card
IIB-1553-ISA
The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Ada Source Code Analyzer
CodePeer
CodePeer is an Ada source code analyzer that detects run-time and logic errors. It assesses potential bugs before program execution, serving as an automated peer reviewer, helping to find errors efficiently and early in the development life-cycle. It can also be used to perform impact analysis when introducing changes to the existing code, as well as helping vulnerability analysis. Using control-flow, data-flow, and other advanced static analysis techniques, CodePeer detects errors that would otherwise only be found through labor-intensive debugging.
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Code Coverage Branch Monitor
CCBM
Verified Systems International GMBH
The Code Coverage Branch Monitor (CCBM) is a set of utilities that allow instrumentation of C source code for the purpose of branch coverage measurement. This encompasses operations for code instrumentation, removal of this instrumentation, retrieval of coverage information, merging coverage information, and displaying this information with reference to the (original) source code.
-
product
Portable Electrical Management Systems
EMS-LCHW50
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Four-Port Tunable Laser System Source
N7714A
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
product
Multi-Channel (Up to Four) MIL-STF-1760 Interface Board for Conduction Cooled PCI Mezzanine Card Compatible Computers
EXC-1553ccPMC/Px(S)-1760
The EXC-1553ccPMC/Px(S)-1760 is a multi-channel (up to four) MIL-STD-1760 interface board for conduction cooled PCI Mezzanine Card compatible computers. In addition, Checksum, SRQ bit and Header Words are supported on each channel. Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.Each dual redundant 1760 channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. The EXC-1553ccPMC/Px(S)-1760 is supplied with C drivers, including source code, and Merlin+ Windows software.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
product
Source Code Review
Source code review, also known as Security Code Review is the process of auditing the source code for an application to verify that the proper security controls are present, that they work as intended, and that they have been invoked in all the right places. Code review is a way of ensuring that the application has been developed to be “self-defending” in its given environment.
-
product
C/C++ Source Code Analysis
CODECHECK
CodeCheck is a programmable tool for checking all C and C++ source code on a file or project basis. CodeCheck is input compatible with all variants of Standard K&R C, Standard ANSI-C/C++, and all C and C++ compiler vendors. We support GCC-GNU Open Source C/C++ compilers. CodeCheck is designed to solve all of your Portability, Maintainability, Complexity, Reusability, Quality Assurance, Style Analysis, Library/Class Management, Code Review, Software Metric, Standards Adherence, and C++ Corporate Compliance Problems.
