Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
7-142706735
Signal Patchcord, RCV, SIM VTAC, 72", DVI-D Male Single Link, 4 Position
-
product
Xtium Frame Grabber Family
The Xtium series delivers higher bandwidth to sustain Camera Link 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color and monochrome cameras, all in a compact, single slot solution.
-
product
High Speed Connectors
Featuring high speed connectors for Cat6a, HDMI, and Camera Link. Find a connector here that suits your high speed needs.
-
product
Phoenix Camera Link Frame Grabber (D24-PE1)
AS-PHX-D24CL-PE1
Phoenix-D24CL is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
FastCamera
FC1700
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787456-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Phoenix Camera Link Frame Grabber (D48-PE1)
AS-PHX-D48CL-PE1
Phoenix-D48CL x1 is a PCI Express board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and line scan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
Stream & Video Quality Analysis System
VQTS-300
VQTS-300 is a self-contained solution, combining: HDMI/DVI, Display Port or LVDS grabber - one of Unigraf UFG-04 range capture cards, order option Powerful stream analysis tools - Unigraf UFG-04 software Sophisticated image quality analyzer - VideoQ VQMA3 software Ideal tool for development labs, software developers and high volume manufacturers Easy-to-use tool, instantly revealing your source-sink link status, video camera or other video device performance User-selectable reporting modes: machine-readable file with Pass/Fail marks detailed multi-page PDF document Manual and automated performance measurement of HDM/DPI links, video cameras and/or video processors Via optional SDI-HDMI adapter VQTS-300 measures the performance of 3G-SDI/HD-SDI video processors
-
product
Camera Link Breakout Box
CLB-501B
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
product
PXIe-1435, Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module
781699-01
Base-, Medium-, Full-Configuration Camera Link PXI Frame Grabber Module—The PXIe‑1435 is a Camera Link image acquisition device designed for machine vision and scientific imaging applications that require high data throughput. The PXIe‑1435 works with any base‑, medium‑, and full‑configuration Camera Link camera, and it is ideal for many industrial, life science, and biomedical imaging applications. The PXIe‑1435 also supports Power over Camera Link (PoCL) and can power cameras through PoCL‑enabled cables. The onboard digital I/O includes four TTL, two optoisolated inputs, and one quadrature encoder.
-
product
Grablink Full XR
For one Camera Link 80-bit, 72-bit, Full, Medium or Base configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO+: Double Camera Link maximum cable lengthPoCL SafePower compliantPCIe x4 bus: 850 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
product
Camera Link PXI Output Module
It is a PXI module to output as a camera link signal NTSC video signal.For outputting a trigger signal when you have the image conversion, you can ignore the delay at the time of conversion.
-
product
Area Scan Cameras
ace Series
Enjoy a new class of digital cameras that will help you to be even more successful and efficient at what you do. High quality and performance levels combined with a low starting list price of only 199 and a small 29 mm x 29 mm housing make Basler ace cameras one of the world''''s best-selling cameras with thousands of satisfied customers. It is available with several resolutions and speeds and with sensors from all leading manufacturers so that you can easily find the right ace camera model for your application. Choose from the most popular and standard proven data interfaces in the vision market: With the ace Gigabit Ethernet models, you benefit from our GigE market leadership, easy multi-camera setups and 100-meter cable length. Camera Link is the interface for high image data transfer. And with USB 3.0 there is an interface technology which is easy to use and real-time capable.
-
product
NI-1483, Full-Configuration Camera Link Adapter Module for FlexRIO
781341-01
The NI‑1483 makes FPGA image processing possible for FlexRIO systems. It supports 80‑bit, 10‑tap base‑, medium‑, and full‑configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the NI‑1483 with a PXI FPGA Module for FlexRIO to perform custom image analysis. FPGA processing is ideally suited for applications that require bit-level processing and very low system latency. Implemented in hardware, FPGA processing does not require CPU intervention. You can process images on the FPGA independently or with a CPU for more advanced preprocessing architectures.
-
product
Area Scan Camera
Area Scan Cameras provide high-performance and high-resolution options that offer excellent image quality and many sensor options. They can connect over a variety of interface standards such as USB3 Vision, GigE Vision, and Camera Link. Models offer high frame rates and rolling or global shutters. Area Scan Cameras are well suited for a variety of applications, such as automated inspection, smart machine control, and factory automation.
-
product
FireBird Camera Link 3U cPCI Serial Frame Grabber
AS-FBD-1XCLD-3CPCIS-2PE4
The FireBird Camera Link CompactPCI Serial card is a member of Active Silicon’s state-of-the-art FireBird frame grabber family. FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Cable, Power over Camera Link (PoCL), MDR to MDR, 5M
199744-05
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
product
Linescan SWIR Camera
LINECAM12
Princeton Infrared Technologies, Inc.
The LineCam12 is an advanced linescan SWIR camera with 14-bit digital data at 37klines/s on USB3 or Camera Link™ outputs. The SWIR camera currently comes in two varieties: 250 μm tall pixels for spectroscopy and 12.5 μm square pixels for machine vision applications. The camera has incredible versatility enabling full wells from 75ke- to 100Me- with 128 steps of variation as well as integration times from 10 µs to 150s. On chip optical pixel binning (where every other detector is disconnected from the ROIC thus signal is captured by neighboring pixels) is available by command to trade spectral resolution for increased signal level. Pixel skipping or binning is also available allowing for 48k lines/s at 512 resolution in the same camera platform, activated by a simple command structure. The TEC stabilized camera has 31 non-uniformity correction (NUC) tables with 15 factory set and 16 user defined tables to enable flexibility for the given environment.
-
product
Phoenix 3U cPCI Camera Link Frame Grabber
AS-PHX-D48CL-3CPCI32-B-CR
Phoenix-D48CL is a 3U CompactPCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
product
Framegrabber
FastX-APU
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
product
Grablink Base
For one Camera Link Base or Lite configuration cameraDirectly compatible with hundreds of Camera Link cameras available on the marketSupports PoCL, Power over Camera LinkECCO: Extended Camera Link cable lengthPCIe x1 bus: 200 MB/s sustained delivery bandwidthFeature-rich set of 10 digital IO linesMemento Event Logging Tool
-
product
Frame Grabbers
* Supporting most performance-demanding Machine Vision protocols, such as CoaXPress, Camera Link HS, 10 GigE, Fiber etc.* Ideally suited for industrial, defense and aerospace Machine Vision Systems.* These products are complimented by sophisticated application software package and SDK, for Windows and Linux OS’s.
-
product
Virtex-5 XMC/PMC
XMC-FPGA05D
Curtiss-Wright Defense Solutions
The XMC-FPGA05D high density I/O module controlled by a user programmable Xilinx Virtex-5 FPGA and supported by a range of front panel I/O modules including analog I/O, RS-485/422, LVDS and Camera Link.
-
product
Framegrabber
FastXe2
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
CL LX1 Base Frame Grabber
Xcelera-CL LX1 Base
Building on the field proven technology and performance of DALSA’s X64 frame grabbers, the X64 Xcelera™ Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility.The PCIe point-to-point host interface allows simultaneous image acquisition and transfer with little intervention from the host CPU.The X64 Xcelera -CL LX1 Base is a cost effective frame grabber based on the PCI Express x1 interface. Fully compliant with Camera Link (V. 1.20) specifications, the Xcelera-CL LX1 supports single Base cameras and can acquire images from a wide variety of multi-tap area and line scan, color and monochrome cameras.
-
product
CL MX4 Frame Grabber
Xtium-CL MX4
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CL MX4 is based on industry standard PCI Express™ Gen 2.0 expansion bus to deliver high speed access to host memory. The new Xtium series offers higher bandwidth to sustain Camera Link® 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color/monochrome cameras, all in a compact, half-length, single slot solution.
-
product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
product
CL PX4 SE Frame Grabber
Xcelera-CL PX4 SE
The X64 Xcelera-CL PX4 SE is a highly versatile PCIe frame grabber capable for one Camera Link™ Base, Medium, or Full camera and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 SE an ideal solution to a wide variety of cost-sensitive applications.
