Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Spectroscopy Lamps and Light Sources
The StellarNet portable Light Sources facilitate measurements in the UV, VIS, and NIR for various samples and application types using standard SMA-905 optical connectors. These low cost modular components are robust, reliable, and designed to last in portable and industrial environments.
-
product
Calibration Light Source
CAL2
Image Engineering GmbH & Co. KG
The CAL2, based on our 22 channel spectrally tunable iQ-LED source, can be adapted for use in many different areas.
-
product
Fiber Optic Light Sources
Fiber optic light sources are a necessity for performing optical fiber network testing to measure the optical fiberal loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the optical fiber power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the optical fiber power meters, they act as an economic and efficient solution for the optical fiber network works.
-
product
Xenon Light Sources
Our pulsed Xenon light source is used in applications where a long lifetime and high output power is needed, such as in fluorescence measurements. This is an affordable UV source, but the spectral output is not as smooth and continuous as the AvaLight Halogen and Deuterium light sources.
-
product
Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-O
Outdoor weatherproof - high reliability against water and insects. Double conductive shielding to eliminate false alarms from light sources. Registers movement in the area covered: 40 ft (12 m) x 50 ft (15 m) - 120° wide. LED lights during detection. Selectable detection paterns: Multi-Level (40 zones) or Pet Alley (18 zones). Unwanted detection areas can be eliminated using the included area masking strips. Selectable Sensitivity: High, Mid and Low. Adjustable to the brightness of surrounding environment with the Day/Night Mode switch. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 122°F (-20 to 50°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Color Sensor
The color sensor product family includes both RGB (Red, Green, Blue) and high-accuracy XYZ light sensors for precise color measurement, determination, and discrimination. XYZ sensors are capable of providing xy chromaticity co-ordinates in accordance with the CIE 1931 color map. The ams color sensors include filters to block unwanted IR light in the visible spectral range, enabling highly accurate color measurement. Their high sensitivity coupled with their wide dynamic range make them well suited to continuous color temperature measurement of ambient light in display management systems, and automatic-white-balance assistance in camera applications. Some products have additional IR channels to assist with IR light source identification.
-
product
Spectroradiometer
SpectraScan® PR-740
The SpectraScan® Spectroradiometer PR-740 is JADAK’s enhanced sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Variable Power Supply
VS-10a
The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.
-
product
LED
light-emitting diode (LED) is a two-lead semiconductor light source. It is a pn junction diode, which emits light when activated. When a suitable voltage is applied to the leads, electrons are able to recombine with electron holes within the device, releasing energy in the form of photons.
-
product
Light Sources
These external units provide illumination which is transmitted to the viewing instrument by a light guide cable, and then through the scope via the integral fiber bundle to the viewing tip.
-
product
Fiber Optic Power Meters
FOD 1204
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
product
DUV Mask Aligner
Model 200E
OAI’S Model 200E DUV Mask Aligner performs all the functions of the tabletop Model 200 Mask Aligner but utilizes a 185nm Excimer Lamp as the UV light source. It is used for Biotechnology Processing.
-
product
Optical Light Sources
A fiber optic source is commonly used with a meter to measure optical fiber attenuation or insertion loss.
-
product
Light Source
UVF-502S
In combination use with the uniform exposure unit, selection of uniform irradiation area in the range of 80mm200mm is possible.
-
product
Multi-Wavelength Optical Light Source
Shanghai Baudcom Communication Device Co.,Ltd.
BD-POW-D02N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at single wavelength, dual wavelength or three wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.
-
product
Spectrometer - OSA
HighFinesse optical spectrometers LSA and HDSA are designed to analyse the multi-line or broadband spectrum of (un-)known light sources like cw and pulsed lasers, gas discharge lamps, super luminescence diodes, semiconductor laser diodes and LEDs. They are suitable to analyze the spectrum of telecom signals, resolve Fabry-Perot modes of a gain chip, and produce a spectral measurement of gas absorption.
-
product
Light Measurement
Light is produced from many natural and artificial sources. Controlling light and having an accurate understanding of its output, directionality and the appearance of what it irradiates is key to product development, quality and the success of a light source. Here are just a few examples of why Labsphere is leading the industry in light measurement.
-
product
Light Sources
Bentham's range of light sources has evolved to suit the requirements of our systems and their users and now offers single or multiple sources from 200nm to 40m:
-
product
Light Sources
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
product
Non-Contact Type Phase Sequence Indicator
895 PR
Standard Electric Works Co., Ltd
● Protection class: IP40● Non-contact detector clips. No metal contact points to advocate greater safety.● Two functions in one unit : open phase and phase sequence detection.● Designed for checking a wider range of 3-phase power sources.● LED display lights with buzzer indicator. ● Brightness button feature for better visibility in dimly lit areas or sunlight.● Magnetic mounting feature.
-
product
Multi-Wavelength Planar Lightwave Circuit Splitter (PLC Splitter)
PLC-2 × 口口口
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar optical waveguide optical splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communication system into multi-way output. The component that we manufactured is with high stability to light source and temperature. And diversified packages can meet customers’ different requirements in application. According to the various requirements, our PLC splitter is with various types: bare fiber type,miniature type, fan-out type,module type, tray type, plug-in type , Blade package type, rack-mounted type, etc.
-
product
Polariser Analyser
*includes analyzer to fit in microscope head and polarizer that fits over light source
-
product
Spectral Lightmeter
MSC15
The compact and user-friendly MSC15 spectral light meter is an inexpensive entry-level light-color-spectral measurement solution for any type of conventional and solid-state light source such as LEDs and OLEDs.
-
product
Dual Wavelength Multimode Light Source
FiberLink 6652
The Fiberlink 6652 Dual Wavelength Multimode Light Source is a cost effective, compact, handheld light source. The temperature compensated outputs are calibrated to couple -20dBm of optical power into multimode fiber.
-
product
Light Monitor
LM-101
The LM-101 Light Monitor system provides an efficient and cost effective solution for monitoring coating thickness in real time. It consists of the LM-101 Light Monitor, LM-101A/AS light source, and Detector assembly.
-
product
Optical Light Source
STC-OLS201 series
Shanghai Stone Communication tech Co., Ltd
a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).
-
product
Pulsed Fiber Amplifier
MOPA
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
product
Fiber Optic Test Kit
KI-TK081
Small single mode fiber optic test kit for low to medium test volume on SM systems. A fiber optic power meter and light source in a padded zip case.
-
product
Optical Talk Sets
JW4103N
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW4103N Optical Talk Set is an intelligent and efficient instrument that combines in one set the functions of both a digital optical phone and a stabilized light source. It is widely used in operations of installation, optical testing, maintenance and fiber attenuation value testing in data network, CATV and Telecommunication network.
-
product
Trace-Level UV Fluorescence SO2 Analyzer
Model T100U
Teledyne Advanced Pollution Instrumentation
The Model T100U Trace-level SO2 analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven UV fluorescence principle, and is designed to allow ultra-sensitive SO2 measurements while still meeting the requirements for use as a US EPA compliance analyzer.The analyzer uses both the light and dark phases of the pulsed UV light source to continuously detect and correct for electronic noise, giving exceptionally stable and sensitive performance. A separate UV detector allows the instrument to continuously correct for variations in lamp intensity. Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift, and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon "kicker" and advanced optical design combine to prevent inaccuracies due to interferents.
