Filter Results By:
Products
Applications
Manufacturers
- Optomistic Products
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Drop Weight Tear Tester
DWTT
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
product
Digital Ultrasonic Maintenance System
VPE-2000
The Superior AccuTrak VPE-2000 is the first digitally controlled ultrasonic detector. Like two instruments in one it uses two independent sensors supported by separate electronic circuits configured specifically to their own sensor. This assures optimum sound clarity and frequency response. When switching between the airborne and contact sensors all settings are retained in memory! Digital LED meters let you establish baselines, perform trending, and accurately repeat these tests better than older more expensive analog instruments.
-
product
Memory Burn-In Tester
H5620/H5620ES
As Server and Mobile applications have mainly led the Memory and market has also entered a super cycle that has completely withdrawn from the previous silicon cycle.Memory capacitance will continue to rise as the application of data processing and mobile communication occurs—however, revenue will not grow as ASP goes down. Suppliers need to reduce test costs and increase profits.H5620 contributes to reduction of test cost by integrating the test process of DRAM Burn-in and Core Test. This hybrid memory test solution solves the challenge of reducing test costs while increasing test efficiency in the expanding DRAM market.
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
Multimeters
Taut-Band movement.26 measuring range with Min. 1mV and 100uA(MS506-A) both in AC and DC.Zero at midpoint function (voltage meter,current meter and galvanometer 3 in 1).Overload warning LED indicator.Input impedance:100kΩ at all voltage ranges.Battery test function
-
product
Earth Resistance Testers
.Multi Test Voltage.Conductor resistance measurement(DET4300).Soil resistivity measurement(DET4300).LCD background light.Data hold.Working LED indicator.Low battery warning.Function symbol display
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Color Tests
LED-Check
LEDs are the standard light source in car cockpits. It is not sufficient to find out if a LED shines, or not. The LED needs to have precisely the specified brightness and color to fulfil its function.The FiberVision LED-Check system tests up to 250 LEDs in less than one second.
-
product
Compact Automatic Voltage Regulating Relays
NMC’s Microcontroller based Automatic Voltage Regulating Relays (AVR Relays) are latest technology based Relays used for regulating the secondary voltage of Power Transformers with On Load Tap Changer (OLTC). The Parameter settings are made through the front panel keys & are stored in NVRAM. Independent time delays can be set for first control pulse & subsequent pulses. Built-in Tap displays Tap number of Power Transformer. OLTC is blocked for UV, OV, OC, CF, Min/Max Tap Positions & Tap Fail . in manual mode, Tap Raise/Lower can be achieved through front keys. In TEST mode, Relays, Display and LED indications can be checked. A pair of contacts are available for Raise, Lower, UV, OV, Manual Mode, CF, TF & OC. There are two nos. of 5 Amps C.T.’s available, one for the Over Current blocking and L.D.C. & other for measuring the Current.
-
product
Contacting Tip Fiber-Optic Probes
Our Fiber-optic Probes with Contacting Tips are designed to achieve a more refined intensity measurement. The intensity response of a Sensor is influenced by several factors, including brightness and size of the LED under test, the aperture of the Fiber-optic Probe that is being used to test the LED, and the distance between the LED and the Fiber-optic Probe tip.
-
product
ESD Simulators
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
product
Digital Voltmeters
*Measures voltage from 5V to 25kV line to line*Large, easy to read LED display*Versatile for overhead and underground applications*Capacitive Test Point and Peak Hold modes
-
product
Vertically Falling Water Drops Device IPX1/2
IEC60529
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005.Satisfying requirements of level IPX1/2. Applide to test LED lamps and house hold appliances, and other electric and electronic products waterproof test of IP code level IPX 1/2.
-
product
LED Fast-Scan Micro-Spectrophoto Colori meter
8000
Shenzhen Chuangxin Instruments Co., Ltd.
The system can determine spectral power distribution, chromaticity coordinates, correlated color temperature, color rending index (Ra), color difference, peak wavelength, spectral half width, dominant wavelength, color purity, luminous flux, test for photometry colorimetry electricity of LED characteristics.
-
product
Automatic Asphalt Content Tester
4000g sample capacity, integrated +0.1gm accuracy weighing scale, High temperature ceramic filtration system and afterburner for accurate measurement of bitumen content in asphalt mixes. Automatic operation through user defined automatic end point detection and 24 hour start timer. User defined control of furnace chamber temperature from 200 – 650oC, Digital display and printing of test data through bright LED displays and integrated printer, Software activated mechanical door lock to prevent door from opening during test process and cutting off power from the heating elements upon opening the door. Operates on Single Phase, 220V, 50 Hz, 20 Amp and consumes less than 5000 W.
-
product
Multi Function Testers
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
-
product
Cable Tester, HDMI Cable, Handheld, Height 102mm, Width 95mm, Depth 27mm
72-13550
*HDMI cable tester with LED status display*Tests for normal/short/open/crossover circuit*Scan/full display testing modes conversion*Single key operation*Manual/auto power off (after 10 minute inactivity)*Low battery indication < 7.2V*HDMI/HDMI-mini interface*9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
product
Lighting Technology LED Solutions
Our OTP² system platform provides the basis for reliable tests of products equipped with single or multiple LEDs. Optical measurement values like color and intensity can be recognized reliably by the integrated LED analyzers. Depending on the application, it is also possible to employ camera systems for the optical evaluation of LEDs.
-
product
Multi-Battery Tester
MBT-1
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
product
Relay Tester
7612
Peaceful Thriving Enterprise Co Ltd
This is the device to test 3 popular vehicle relays. The testing result will be displayed by LED indication. Technician is able to use the device to figure out the condition of the relay, and so speculating the problem in the vehicle.
-
product
LED Tester
Pocket-size LED tester.Easily check functionality, color, brightness and uniformity.Plug any leaded LED into one of 12 positions on the socket strip to test at current ratings from 2-50ma.The seven middle positions on the strip are set at 10 mA allowing comparison of LEDs in those spaces.Requires a 9V battery (not included).
-
product
Data Diver
MT-8006B
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
product
GO-SPEX100 Goniospectroradiometer
Hangzhou Everfine Photo-E-Info Co., LTD
GO-SPEX100 delivers photmetric, colorimetric, electrical comprehensive test function for LEDs, and built-in precision temperature control platform,not only for measuring the specific temperature of the photometric and colorimetric parameters of LED, but also to measure the characteristics curve of its photometric and colorimetric performance with temperature.The test parameters include: spatial luminous intensity distribution curve, luminous flux, spatial spectral distribution, relative spectrum, absolute spectrum, color parameter, forward current and forward voltage, etc.
-
product
LT-500A Aging-Life Test System For LED Luminaires
Hangzhou Everfine Photo-E-Info Co., LTD
LT-500A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
product
Flying Prober Test
QTOUCH1202C
Qmax Test Technologies Pvt. Ltd.
he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.
-
product
LED Test
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
product
Analogue (1kV up) H.V. Insulation Tester
6201 IN (Ranges: 5kV, 10kV)
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● High quality Taut Band movement.● Two insulation test voltages.● Insulation resistance, auto ranging on all ranges.● Low Battery LED indication.● Beeper warning of external voltage.● Fully protected : crow bar.● Housed in carry case.
-
product
H.V. Detector
290L HD
Standard Electric Works Co., Ltd
● Telescopic, compact, lightweight● High voltage detection● Self test button feature● Easy to recognize indication● High intensity red LED and intermittent audible alarm for easy recognition in full sunlight and noisy environments● Waterproof
-
product
Voltage Detector
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
product
4 + 4 LED Driver Test Panel
SCR Elektroniks make 4+4 LED Driver Test Panel to test the driver one by one.
