Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Single Port RS-232 Interface
PCI-COM232
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
product
Logic Analyzer Prodigy
PGY-LA-EMBD
Prodigy Technovations Pvt. Ltd.
The Discovery logic analyzer series, PGY-LA-EMBD has built-in capability of I2C logic analyzer, SPI logic analyzer, and UART logic analyzer . This is pc based logic analyzer. The Discovery logic analyzer is used to debug embedded systems , the logic analyzer not only reduces the work bench area but also allows to has very small form factor and can be used to debug failures in the field .The protocol decode capabilities are designed to debug the logic and protocol issues faced by embedded design teams in consumer, industrial, home automation, health and education sectors.
-
product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
product
Evaluation Kit
ROM-DK2620
*NXP Arm® Cortex®-A35 i.MX 8ULP Dual up to 1.0 GHz*1 x Arm Cortex-M33 core*Onboard LPDDR4 1GB, 2000MT/s memory*1 x 4 lane MIPI-DSI*1 x USB2.0, 1 x USB 2.0 OTG, 5 x UART, 2 x I2C, 24 x GPIO, 6 x PWM, 1 x CAN*Support Ycoto Linux
-
product
Low Profile PCI Express 2-Port
7202ec
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
product
PMC-BiSerial II-NG1
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
product
PMC-Serial
The PMC-Serial is capable of providing multiple serial protocols, both synchronous and asynchronous with a wide range of baud rates. The PMC-Serial has up to 8 UART channels, and two SCC channels. The protocol processors are complemented with a variety of IO which can be selected as a build option. RS-232, RS-485, RS-422, and RS-423 are supported. Two enhanced hysteresis MIL STD 188-114A receivers, and two open drain active low output drivers are also provided.
-
product
SparkFun Breakout
FT231X
Introducing the SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned Arduino boards. It can also be used for general serial applications.
-
product
3.5" Single Board Computer
RSB-4680
RSB-4680 is a RISC 3.5" single board computer (SBC) powered by a high-performance Rockchip ARM Cortex-A17 RK3288 processor which supports 4K display from HDMI. It offers rich interfaces such as 6 USB2.0, 6 UART, 1 VGA, 1 LVDS, 1 GbE and 8 GPIO. RSB-4680 also features Mini-PCIe, M.2, and SIM card slots for integrating Wi-Fi, Bluetooth, and 3G/4G modules. It is an ideal solution for Kiosk, POS, and Vending machine application.
-
product
16-Port RS232 Async Serial Communications Adapter PMC
2238
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
product
PCI Express 2-Port
7203e
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Open Pluggable Specification (OPS) Digital Signage Player With 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H81 And TPM 1.2
OPS883-H
The OPS883-H OPS-compliant digital signage player is powered by the 4th generation Intel® Core™ i7/i5/i3 processor (codename: Haswell) with the Intel® H81 chipset. It has one 204-pin DDR3 SO-DIMM socket with maximum up to 8 GB. It offers stunning 4K Ultra High Definition (UHD) content via a HDMI port. The Intel® Core-based OPS883-H is ideal for multi-display applications in airport information board, shopping mall, corporate, education, hospitality, religious organization, bank, retail store, restaurant, performing art center and many more. This smart pluggable signage module is connected to OPS-compliant display via a standardized JAE TX-25 plug connector, and includes DisplayPort, UART, audio, USB 3.0 and USB 2.0 signals. To fill different application needs, the signage unit reserves a wide choice of I/O ports on front panel, including one USB 3.0 ports, two USB 2.0 ports, one COM port, audio (in/out) and a Gigabit Ethernet port. This slim-type OPS system has one internal PCI Express Mini Card slot to connect Wi-Fi or 3G/ LTE modules to satisfied users wireless needs. It features one easy-to-access 2.5” SATA HDD as storage device. Also, it supports TPM 1.2 feature which is designed to secure system.
-
product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
product
PCI Express 8-Port
7804ec
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
product
Enhanced Serial Interface Module for Excalibur 8000 Family of Carrier Boards, with High Baud Rate & High Throughput
M8KSerial
The M8KSerial is an enhanced serial interface module for the multiprotocol Excalibur 8000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to two independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M8KSerial module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 8000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M8KSerial module is supplied with C drivers, including source code.
-
product
PCI Express 16-Port RS-232 Serial Interface
7161e
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
product
Edge Gateway
EPC-R4680
EPC-R4680 is an ARM based Box Computer powered by Rockchip ARM Cortex-A17 RK3288 Quad core high performance processor, which supports 4K display and 4Kx2K multiformat video decoding via HDMI. It also features M.2, Mini-PCIe and SIM card slots for WIFI, BT and 4G connectivity. EPC-R4680 also offers rich interfaces such as 6 USB2.0, 6 UART, 1 GbE and 8 GPIO. It is an ideal solution for Kiosk, Vending machine and Digital signage application.
-
product
4-Port RS232/4-port RS422
3101
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTS, with four ports using RS232 signal levels, and four ports using RS422 signal levels. The four RS232 ports each provide the full set of data and modem control lines configured for DTE
-
product
SparkFun USB To RS-485 Converter
This is the newest revision of this board and this breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART IC to convert a USB stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps.
-
product
Module Spectrum
nRF52820 Series
Nordic nRF52820 solutioin features an Arm Cortex-M4 processor with 256 KB Flash and 32 KB RAM. Supports SPI, UART, I2C and USB interfaces
-
product
Modules
Cimetrics offers several modules that can enable you to add BACnet capability to your products. Our modules, based on the Lantronix XPort, are elongated Ethernet RJ45 connectors that can be built into your product. Each module contains a microprocessor, memory, Ethernet MAC/PHY, serial (UART) interface, and firmware written by Cimetrics. The serial interface is typically used to communicate with another microprocessor in your product.
-
product
Logic Analyzer
LAP-16128U
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals.
-
product
XYZ Color Sensor
AS7261
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
-
product
Low Profile PCI Express 2-Port
7205ec
The 7205ec low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7205ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
product
Low Profile PCI Express 4-Port
7406e
The 7406e low profile PCI Express serial interface provides four RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Low Profile PCI Express 2-Port
7204ec
The 7204ec low-profile PCI Express serial interface provides two serial ports configurable for RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7204ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
Control Board For Testing PCBs
TCC 1800
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
product
Serial Board
104-COM232-8 Series
This is an eight, four, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports full RS-232 serial communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors for the boards optional breakout cable. The boards are feature-rich and allow for the connection of multiple serial devices—ideal for a variety of applications such as POS, barcode readers, modems, machine monitoring and control, military, high-density networking applications or any other application requiring the connection of RS-232 serial devices to a PC/104 compatible system. Type 16780 UARTS are used as the asynchronous communication elements. These include 64-byte transmit/receive FIFO buffers to protect against lost data in multitasking systems while maintaining 100% compatibility with all operating system COM port drivers. ACCES offers the 104-COM232-8 series in both standard and extended temperature versions ideal for outdoor applications or harsh industrial surroundings. Ordering options include UARTs with larger FIFOs, support for custom baud rates, vertical I/O pins, and custom cabling.
