Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Circuit Synthesis Software
Optenni Lab
Optenni Lab™ is the leading circuit synthesis software for antenna optimization aiming at efficient assessment and optimization of antenna systems at any design phase. Optenni Lab features automatic matching circuit synthesis and optimization, antenna array beamforming with active impedance control, and many supplementary assessment tools. Optenni Lab is often used in conjunction with EM simulators, and several links are provided with major EM tools on the market.
-
product
24V Heavy Duty Circuit Tester
27430
Heavy duty probe, cord and clamp. The probe is insulated with high-visibility shrink tubing to prevent the possibility of shorting the side of the probe to other components. Comes with a strain relief spring on the cord.
-
product
Circuit Breaker Testing
HAOMAI Electric Test Equipment Co., Ltd.
Circuit Breaker Testing is utilised to test the operation of each switching systems and the programming of the entire tripping structure.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7222
This model is a 2,000 count stable, safe and reliable digital clamp multimeter. It is designed with large-scale integrated circuits and A/D converter as the core as well as the overload protection and novel structure, which make them a superb tool of electricians.
-
product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Transistor-Level Defect Simulator
Tessent DefectSim
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
product
Impulse Test Equipment
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
product
Impedance Matching Pads
Impedance matching pads from BroadWave eliminate impedance discontinuity (mismatches) without introducing reflection to the circuit. Custom units are available in a variety of impedance and connector types from DC to 4 GHz. BroadWave Technologies impedance matching pads preserve signal integrity by matching virtually any transmission line.
-
product
Pressure Sensors
Pressure sensors have particular utility for monitoring the pressure in a fluid network. As compared with flow sensors, pressure sensors often require less cost to achieve a similar result. Pressure sensors are often fabricated using thin membranes that flex under pressure.Some pressure sensors function in a binary manner, i.e., when pressure is applied to a pressure sensor, the sensor acts to complete or break an electical circuit. Some speed cameras use them.
-
product
90-300V AC/DC Voltage Tester
1928A
Peaceful Thriving Enterprise Co Ltd
*Handy pocket clip.*With cETL Approval.*Bright neon indicator.*Insulated housing and test leads.*Check voltage on 90-300V AC/DC.*Built-in lamp will glow if the circuit is live.
-
product
47~2400MHz FTTH CATV & SAT-TV Optical Receiver
HRS-24-H1
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-24-H1 product series is a kind of CATV & SAT-IF optical receiver with high-performance and high-index. 7~2400MHz operate bandwidth. Output level Vo=86dBμV ( Pin=-2dBm ), suitable for FTTH, FTTP fiber access network. It is a low power consumption, high performance and excellent cost performance CATV & DBS network ONU(Optical network unit). This series product adopts high sensitivity receiving tube and special low noise matching circuit. Under 3.8% modulation, when transmitting in full channels and with receiving power of –8dBm, the CNR can still reach high index of 48dB and low inter modulation index. If adopting HRS-24-H1, it is only need very low optical power to reach 48dB CNR required by the user.
-
product
÷10, 500 MHz, 10 MΩ, Passive Probe
PP009-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Circuit Break Timer Test Set
PME-500-TR
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
product
Step Recovery Diodes
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
product
Multimeter Network Tester
VA16
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
product
Flex Test Fixtures
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
product
RS-232 to EIA-530 Interface Converter
Model 62-1 / 62-2
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
product
Visual Fault Diagnostics and Repair System
ScanExpress Viewer
ScanExpress Viewer™ is a printed circuit board (PCB) CAD data & photograph visualization tool for boundary-scan test development, electronic manufacturing test, and product repair environments.When combined with ScanExpress ADO™ (Advanced Diagnostics Option) for detailed results from ScanExpress Runner™, ScanExpress Viewer displays fault coordinates and connected traces superimposed directly on a board photograph or CAD layout diagram for expedient repair.
-
product
Surface Potential Measuring Instrument
In the electronic equipment assembly process, there are many items that are charged on the order of kV, such as resin molded products and films. This digital electrostatic potential measuring instrument is suitable for processes with relatively high electrostatic control voltage.The measurement range switching function makes it possible to measure from low potential measurement of electronic devices to high potential measurement of resin molded products, film / printed circuit board manufacturing, etc.
-
product
Photonic Components
Fraunhofer Institute for Telecommunications
The Department of Photonic Components is researching optochips and Photonic Integrated Circuits (PICs) for transmission and reception of more than 100 Gbit / s and the sensors. The department provides production and development services for all activitiesfor the German and international industry. If, for example, you already think of a particular optochip concept, the researchers offer additional advice and take over design and production steps. On the other hand, if you would like to start with a target specification, a feasibility study will begin and your own concept will be developed for you. Researchers are always ready and able to carry out initial production volumes in an ISO certified, qualified manufacturing facility. In addition, e-beam services and diffractive optical elements developed according to specifications are offered.
-
product
Cable Tester, HDMI Cable, Handheld, Height 102mm, Width 95mm, Depth 27mm
72-13550
*HDMI cable tester with LED status display*Tests for normal/short/open/crossover circuit*Scan/full display testing modes conversion*Single key operation*Manual/auto power off (after 10 minute inactivity)*Low battery indication < 7.2V*HDMI/HDMI-mini interface*9V battery (6F22)*12-month limited warranty *view Terms & Conditions for details
-
product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120CG-CM-X8G3
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
GPIB Parallel Interface
Model 4823B
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
product
Electro Pneumatic Circuit
Unitech Scales And Measurements Pvt. Ltd
Electrical control of double acting cylinder by solenoidvalve.
-
product
Semi-Rigid Test Probes Up to 6 GHz
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
product
Clamp Meters
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication
-
product
Function Generators
Scientific Mes-Technik Private Ltd
Scientific offer wide range of function generators from 3 MHz to 10 MHz in general purpose and multifunction. Selection of waveform shapes apart from standard sine, triangle , square to ramp, pulse are available. SM5071 , SM5074 , SM5061 & SM5075 have built-in auto ranging frequency counter. The outputs are protected against short circuits and overload.
-
product
Insulation & Multifunction Tester (OLED Display)
1155 TMF-M
Standard Electric Works Co., Ltd
● High Contrast OLED display.● Designed for viewing in the dark, for mining industry.● Auto-range microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto-discharge on all tests and all ranges.● Leads auto-null key.● Test auto-stop.● Smart hold and stop on voltmeter AC/DC.● Ener-Save.● Continuity short circuit >220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Polarization index (PI).● Dielectric Absorption Ratio (DAR).● BS 16 edition.
-
product
Analog Multimeter
YX-360TRD
DCV & ACV & DCA & OHM & CAP test. Overload protection circuit up to maximum 230V is provided. Designated for measurement of weak current circuits. Our technology has made it possible to measure high resistance with low voltage. Panel face protection cover which serves also as a stand is employed
