Filter Results By:
Products
Applications
Manufacturers
Asynchronous Transfer Mode
Testing Asynchronous Transfer Mode (ATM) communications and network equipment includes three primary testing phases: conformance verification; interoperability testing; performance benchmarking
-
product
Modules
1x9 BIDI Transceiver Modules
The module supplies best solution of short-haul 20 km for fiber optical system and link distance. The module with the Differential PECL of 3.3 or 5 Voltage and provide the system designer with products to implement a range of ATM (Asynchronous Transfer Mode) and SONET for Telecommunication. The module was all supplied in the new industry standard 1x9 SIP package style with a Bi-directional BIDI SC ST or FC connector interface.
-
product
OC-3/STM-1 And OC-12/STM-4 Analysis And Emulation Card(w/ GigE And USB 2.0)
LightSpeed1000™
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames. GL's LightSpeed1000™ hardware platform (PCIe Card and USB Pod) is capable of OC-3/12 and STM-1/4 wire-speed processing on quad optical ports for functions such as wire-speed recording and wire-speed playback of Unchannelized and Channelized ATM, PoS, and RAW Traffic.
-
product
PC104 MIL1553A & MIL1553B Board
MS 1701
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
product
Direct Access To T1 E1 DS0 On OC-3/12 STM-1/4 On LightSpeed1000™
Voice, data, and video traffic is exploding as smartphones, IP TV, video streaming, and "cloud" based services takeoff. A majority of the backbone transport for these applications continues to be SONET and SDH optical transmission networks. A dominant protocol for IP transport is PoS (Packet over SONET) and another is ATM (Asynchronous Transfer Mode). Both schemes are packet based, with ATM using fixed size packets of 53 bytes called "cells", and PoS using variable packet sizes closely matching to Ethernet frames.
-
product
PXI-2598, 26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module
778572-98
26.5 GHz, 50 Ω, Dual-Transfer PXI Transfer Switch Module—The PXI‑2598 is a general-purpose switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2598 is also well suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2798, 40 GHz, Dual-Transfer PXI Transfer Switch Module
782358-01
40 GHz, Dual-Transfer PXI Transfer Switch Module—The PXI‑2798 can route RF or microwave signals in automated test applications. Designed to operate with less than 1 dB insertion loss at up to 40 GHz, the PXI‑2798 appears almost invisible to signals at much lower frequencies as well. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2798 is also well-suited for passing high-order harmonics from RF upconverters or routing multiple sources to RF downconverters.
-
product
Asynchronous Fast SRAM
For industrial and communication applications, 4 MB Asynchronous Fast SRAM is available.
-
product
Asynchronous System Level Test Platform
Titan
The Titan System Level Test (SLT) platform delivers maximum flexibility, scalability and density in semiconductor test environments that require the highest levels of system performance testing. Titan is Teradyne’s solution for high-volume mobile application processor SLT requirements.
-
product
Transfer Switches
Q Series
The Pro/Tran Q Series features 1-inch interchangeable circuit breakers. A 30A double-pole circuit breaker and a 20A double-pole circuit breaker, to handle heavier loads on the generator side, are included on each model. The balance of the circuit breakers are single-pole 15A.
-
product
4/8-port Asynchronous Serial Communications Modules
cPCI-3534/3538-S
- 32-bit CompactPCI, PICMG 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- 4/8 asynchronized communications ports with intelligent buffer- Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538- Surge protector in TXD/RXD signal line
-
product
Mode Locked Synthesizer
IT9200
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
product
Common Mode Chokes
Common Mode Chokes, as the name implies, are designed to attenuate and filter common mode noise within an electric system. The key parameters for a common mode choke are the current rating (to ensure the part does not overheat within the application), the impedance versus frequency (to ensure it is optimized to attenuate the desired frequencies), the isolation voltage (to ensure it meets board level requirements between the line and neutral phases) and safety isolation (to ensure it meets the safety requirements of the end-application). It is important to remember that common mode chokes cannot saturate in the application (under normal use) as they are designed to ensure that the line and return currents are balanced.
-
product
Mixed Mode Testing
The Mixed Mode add-on modules for the Random Vibration Control Software allow tests to run with sine tones and/or narrowband random signals superimposed on a random background. Mixed mode testing is a complex control task, and m+p VibControl supports three modes: Sine-on-Random (SoR), Random-on-Random (RoR) and Sine-on-Random-on-Random (SoRoR). Gunfire burst control can also be superimposed in each case.
-
-
-
-
product
Polarisation Mode Dispersion
PMD500
PMD500 is our polarisation mode dispersion (PMD) measurement system available in two PMD measurement methods, designed to produce accurate measurements quickly and with confidence.
-
-
-
-
-
product
Power And Data Transfer
Cable reels & slip ring assemblies for reliable power and data transfer in mining, construction and material handling applications.
-
product
Power Transfer Unit
The PTU is a bi-directional, back to back, variable/fixed displacement unit, with a differential pressure compensated displacement control. Displacement of the variable displacement unit is varied to maintain the required running and breakout pressure differential between the yellow and green systems.
-
-
product
LCD Arbitrary Test Mode
AllWin Instrument Science and Technology Co., Ltd.
1. Set test mode arbitrarily2. LCD display,menu guiding operation3. Equipped with PLC interface ,optional RS232interface,RS48
-
product
ModCon Mode Controller – Aerospace
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet 85/85 launch conditions required in some aerospace applications.
-
product
ModCon Mode Controller – OEM
*Improve measurement accuracy*Ensure stable launch conditions for multimode fiber measurements*Meet EF requirements of IEC 61280-4-1.
-
product
Acceleration Simulation Mode (ASM)
Maschinenbau Haldenwang GmbH & Co. KG.
MAHA Acceleration Simulation Mode (ASM) Products
-
product
Firmware for High-speed HDLC Mode
OP-FW10G
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
