Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PCIe Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCIE-1516
8 digital inputs, 24 V, isolated15 interruptible inputs8 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
PCI Three-Axis Laser Board
N1231A
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
Qseven® Reference Carrier Board
Q7-BASE
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
product
Motion Control Terminal Board For Panasonic Minas A Servo
DIN-814PA
- Motion control terminal board with 100-pin SCSI -II cable- On-board connector type: 100-pin SCSI-II female- Suitable for Panasonic Minas A servo- Shipped with 1-meter ACL-10250 cable- Available for PCI-8134, PCI-8164 and PCI-8158- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
3.5" Single Board Computer With 13th Gen Intel® Core™ I7/i5/i3/ Celeron® Processor
SBC35-RPL
SBC35-RPL is powered by Intel's latest processors, which offer improved performance, power efficiency, and support for the latest technologies based on Intel's 13th generation of 3.5-inch Single Board Computers (SBCs) offer a range of advanced features and capabilities for a variety of embedded applications.
-
product
3U CompactPCI® Serial XMC Module Carrier Blade
cPCI-A3XMC
- 3U 4HP CPCI-S.0 peripheral- One XMC slot- Operating temperature: -40°C to 85°C with qualified components
-
-
product
FPGA Processing Board
VP880 / VP881
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
product
Computer On Module
ITX-M-CC452-T10
The ITX-M-CC452-T10 is an industrial Mini-ITX small form factor Type 10 reference carrier board designed to fully test WINSYSTEMS’ COMeT10-3900 COM Express Type 10 Mini module. The carrier board adheres to the PICMG COM Express specifications providing compatibility with other COM Express mini type 10 modules.
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
product
3.5" Single Board Computer With Intel® N97 Processor
SBC35-ALN
SBC35-ALN, powered by Intel® N97 Processor, is exceptionally well-suited for a wide range of applications, specifically tailored for EV Chargers. This 3.5-inch Single Board Computer (SBC) from Intel's 13th generation excels in superior performance, power efficiency, and compatibility with cutting-edge technologies.
-
product
96-Channel Digital I/O Plug-In
1260-114
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
product
Printed Circuit Board
RISER-PCM-1
WINSYSTEMS’ RISER-PCM-1 boards are designed to provide extra space in a PC/104 stack. They are printed circuit boards (PCBs) with PC/104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
product
Extreme Rugged PCI-104 Single Board Computer with Intel® Atom™ Processor E3800 Series SOC
CM3-BT1
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
3.5" Single Board Computers
SBC35 Series
ADLINK's SBC35 Series of 3.5" single board computers combines compact design with high performance, suitable for diverse industrial applications like automation, transportation, and smart cities. Featuring the latest Intel® processors within a 146x102mm footprint, these boards are enhanced by SBC-FM Adaptive Function Modules, offering powerful processing, extensive I/O options, and customizable scalability. Perfect for upgrading systems or developing new solutions, the SBC35 Series delivers advanced technology and adaptability to meet specific project needs efficiently.
-
product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
product
PICMG® 1.3 Full-Size 6th generation Intel® Core™ i7/i5/i3 LGA1151 Processor-based SHB (Code name: Skylake)
NuPRO-E43
The ADLINK PICMG 1.3 SHB, the NuPRO-E43, supporting the 6th Gen IntelR Core i7/i5/i3 processor and equipped with the IntelR Q170 Express chipset. The NuPRO-E43 supports high-speed transfer interfaces such as PCIe3.0, USB 3.0, and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2133 MHz memory up to 32 GB.
-
product
ARM Computer
SYS-398D-2G-0
WINSYSTEMS’ SYS-C398DL single board computer combines high-performance multimedia graphics with a rich mix of industrial I/O. The NXP i.MX 6DL processor’s integrated power management provides excellent efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
product
FPGA Board
VP889
The VP889 is a high-performance FPGA processing board featuring Xilinx® Virtex Ultrascale+™ and Zynq® Ultrascale+™ technology.
-
product
Digital Output Board
VME-2128A
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
