Filter Results By:
Products
Applications
Manufacturers
-
product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/400mm J1
111EXT3140-11xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME J1 10 Slot with ADC Connectors
101VMEJ110-0590
VME J1 backplane 10 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 12 Slot with ADC Connectors
101VMEJ112-0590
VME J1 backplane 12 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 16 Slot with ADC Connectors
101VMEJ116-0590
VME J1 backplane 16 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 17 Slot with ADC Connectors
101VMEJ117-0590
VME J1 backplane 17 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 18 Slot with ADC Connectors
101VMEJ118-0590
VME J1 backplane 18 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 20 Slot with ADC Connectors
101VMEJ120-0590R
VME J1 backplane 20 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 21 Slot with ADC Connectors
101VMEJ121-0590
VME J1 backplane 21 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 3 Slot with ADC Connectors
101VMEJ103-0590
VME J1 backplane 3 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 4 Slot with ADC Connectors
101VMEJ104-0590
VME J1 backplane 4 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 5 Slot with ADC Connectors
101VMEJ105-0590R
VME J1 backplane 5 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 6 Slot with ADC Connectors
101VMEJ106-0590
VME J1 backplane 6 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 8 Slot with ADC Connectors
101VMEJ108-0590
VME J1 backplane 8 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME J1 9 Slot with ADC Connectors
101VMEJ109-0590
VME J1 backplane 9 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
3U VME J1 Classic 2-slot With 12A Fastons
50510-202-3600
3U VMEbus J1 backplane 2-slot, VITA, termination passive inboard, daisy chain without power, power connection 12A fastons, I/O pins 13mm gold-plated, shroud (1P1) without latches.
-
product
3U VME J1 Classic 10-slot With 70A M4 Power Bolts
50510-210-0000
3U VME Bus J1 Classic Backplane 10-slot, VITA, termination passive inboard, daisy chain automatic active, power connection 70A power bolts, I/O pins 13mm gold-plated, shroud (1P1) without latches
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
Cable Assembly, Receiver, 20", Micro Power to 41-Pin FML Power Connector, for VTI EX1200-2001 Switch Module
540249010147
CBA, RCV, MicroPWR to 41-Pin J1 PWR Conn f/VTI EX1200-2001 Switch Module.
-
product
Cable Assembly, Receiver, 36", Micro Power to 41-Pin FML Power Connector, for VTI EX1200-2001 Switch Module
540249010247
CBA, RCV, MicroPWR to 41-Pin J1 PWR Conn f/VTI EX1200-2001 Switch Module.
-
product
CPCI Based 486DX4 Board
MS 1501
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
product
Hard Metric Eurocard Plugbord
8020
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole and peripheral bus both sides. Pad and bus surfaces not solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Hard Metric Eurocard Plugbord
8018
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector.Pad-Per-Hole both sides.Combination Pattern: Half 2mm grid and other half 0.1” grid. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Hard Metric Eurocard Plugbord
8017
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad-Per-Hole both sides.Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Hard Metric Eurocard Plugbord
8028
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad per hole both sides. Combination Pattern: 0.100", 0.050" and 2mm grid.Pad and bus surfaces solder coated.Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Hard Metric Eurocard Plugbord
8024
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. 3-Hole solder pads both sides. Pad and bus surfaces solder coated. Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
-
product
VME 32X 5 Slot 6U
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
