Filter Results By:
Products
Applications
Manufacturers
-
product
IDA Electrodes
Interdigitated Array (IDA) electrode is an electrode developed for electrochemical measurements to be performed in a very small quantity of the sample. IDA electrode could be applied for the detection and reaction analysis of the compounds in a small quantity of the sample. IDA electrode is a microelectrode pattern fabricated by using the lithography technology. The Electrodes are composed of 65 pairs. In each one of the pair has a function of the oxidation and reduction electrodes.
-
product
ORP Meters
ORP (Oxidation Reduction Potential) measures a system’s relative state for gaining or losing electrons. ORP values are affected by all oxidizing and reducing agents, not just acids and bases that influence pH measurement. In practice, ORP measures the ability of a lake or river to break down waste products, like contaminants and organic matter. When the ORP value is high, there is lots of oxygen present in the water.
-
product
Pen Type Oxidation-Reduction Potenial Meter
Pen type ORP (oxidation reduction potential) meter is set pH measurement and control and redox measurement and control in one multi-function intelligent instrument. Simultaneously displayed ORP value and temperature. Its full function, stable performance, easy to operate and so on. Making it the best choice for enterprises wild and laboratory testing and control ORP value. The ORP value monitoring is widely used in the chemical, pharmaceutical, electronics, food and other industries.
-
product
Water quality profiler with optical fast DO sensor
AAQ-RINKO
The water quality profiler, AAQ 1183 has been redesigned as AAQ-RINKO with an optical fast response (63% response in water, 0.4 s) DO sensor, RINKO. Conventional water quality profilers with a slow response DO sensor require holding the instrument for a certain period at the measurement depths. AAQ-RINKO makes vertical measurements possible with a profiling speed of 0.5 m/s, similar to CTD observation, thereby significantly reducing the observation time. In addition to conductivity, temperature, depth, chlorophyll, turbidity, DO and pH, AAQ-RINKO also enables simultaneous installation of PAR (Photosynthetic Available Radiation) and ORP (Oxidation Reduction Potential) sensors. The processing unit is available in three types in accordance with the observation applications.
-
product
Noise Reduction
Applied Research and Technolgy
Eliminate ground hum with our specialized transformers and isolators.
-
product
Data Reduction
Data reduction systems with or without time history recording to throughput disc are frequently used in critical aerospace testing applications where complete measurements of a high number of channels are required for post-test and possible failure analysis. The m+p VibControl data reduction system configurations are tailored to the specific needs of high-performance measurement applications requiring hundreds or thousands of input channels.
-
product
Oxidation Stability Tester
K10670
Chongqing Kailian Yongrun Industrial Co.,Ltd.
To measure resistance of lubricating grease to oxidation when stored statically in an oxygen atmosphere in a sealed system at an elevated temperature under conditions of test
-
product
Oxidation Stability Tester
K5908
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to measure oxidation stability of steam turbine oils by rotating pressure vessel; Conforms to SH/T 0193, ASTM D2272; Automatically test pressure of sample oil, calculate time of oxidation, record data, store data and print out; Curve and data displayed on screen; Two bombs design, two tests can be done at the same time, convenient for parallel experiment.
-
product
Oxidation Stability Testers
Automatic lubricating oils oxidation stability tester, transformer oil oxidation stability tester, distillate fuel oil oxidation stability tester, gasoline oxidation stability tester (induction period method)
-
product
Data Acquisition and Reduction
STI offers custom virtual instrument design with LABVIEW software and National Instruments data aquisition cards. Calibration systems include shock accelerometer calibration based on Hopkinson bar, transverse sensitivity, calibration of accelerometers at various temperatures (includes environmental chamber temperature control, shaker motion control, data acquisition and processing) as well as data aquisition and processing systems for turbomachinery and general vibration applications.
-
product
Wind-Noise Reduction System
WNRS
The Wind-Noise Reduction System (WNRS) is an array of air inlets connected with pipes to reduce wind-noise and improve signal quality.
-
product
Sine Reduction Test
Sine Reduction Test - Sine Processing With COLA SignalIntegrate and synchronize the data acquisition system seamlessly with your vibration shaker COLA signal and perform a powerful evaluation of structural properties on unlimited channels in real-time. The Dewesoft sine processing solution is easy to set up and will get you measuring right away.
-
product
Wet Oxidation TOC Analyzer
TOC-VWP
Phosphoric acid and the oxidant (persulfate) are added to the sample, which is heated under UV illumination to convert the TC in the sample to carbon dioxide. This carbon dioxide flows with the carrier gas via the dehumidifier into the NDIR sample cell. The area of the carbon dioxide peak signal is measured and this peak area is converted to TC concentration using a pre-prepared calibration curve.
-
product
Oxidation Stability & Cold Flow Properties
These Anton Paar instruments enable you to evaluate the oxidation stability as well as the storage and thermal stability of mineral oil products or oil and fat containing cosmetics and food samples. The gum content tester is available for tests on the gum content of fuels and other volatile distillates. Cold flow properties (cold filter plugging point and cloud and pour point) show the lowest temperature for a trouble-free operation of diesel fuel or heating oil.
-
product
Wet Oxidation System For VCSEL Fabrication
VIXEL-320
s a wet oxidation system intended for the fabrication of Vertical Cavity Surface Emitting Lasers. It is an atmospheric-pressure oxidation system with in-situ monitoring of oxide aperture formation. It accommodates single wafers of up to 150mm (6? in diameter.
-
product
Noise Reduction Water Leak Detector
DNR-18
With digital noise reduction that removes intermittent sounds like barking dogs and passing vehicles. DNR-18: the advanced digital CPU eliminates intermittent interfering noises, like passing vehicles, people talking, and pedestrian footsteps.
-
product
Translating process images into significant tool-defect reduction
Trans-Imager
Real-time, tool-specific defectivity data. Now there is a way to monitor defectivity on individual processing tools – automatically – in real-time. Microtronic’s new Trans-Imager software module is able to take high-resolution images directly from your processing equipment and immediately detect and displaymacro wafer defects – transferring all of that information into our powerful and long-proven ProcessGuard software which provides a wealth of defect management and analysis. This new capability is called ProcessGuard Xtensis (PGX) because it extends the power of ProcessGuard software to fab tools that previously had no way to detect defects. This provides an important new stream of defect data.
-
product
Companion Tool to VS for Test Time & Pin reduction
UltraScan
UltraScan is SynTest's solution to combat increase in test time. In 130 nm or smaller ? nanometer geometries, many defects become delay defects and it becomes necessary to use delay tests to detect the transition faults and path delay faults. Often bridging tests are also required.
-
product
PC-Card Style RoHS (Reduction of Hazardous Substances) Compliant, Lead-Free Power Supplies
Series MTW
Kepco's Series MTW are three affordable PC card-style RoHS (Reduction of Hazardous Substances) compliant, lead-free power supplies that offer 15, 30 and 60 watts of triple-output low voltage d-c for space and cost-sensitive OEMs. All three models produce triple outputs comprised of 5 volts and ±12 volts d-c from an a-c input that accepts 85 - 265V a-c. They will also accept a d-c input from 110 - 370V d-c. The 5V output is isolated from the ±12V outputs.
