- Virginia Panel Corporation
product
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position
510143006
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position.
-
product
Mixed Signal Test Systems
MTS1020i
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
Mixed signal LSI test system
Multi-pin type model is now launched in WL27 Logic/Power mixed LSI test system.This system is suitable for multi-site test in A/D mixed device such as automotive・motor driver IC. It’s a high throughput and cost performance mixed signal LSI test system.
-
product
Software
Digilent’s proprietary software solutions enable you to communicate with our system boards and a wide assortment of logic devices and use our available analog and digital test & measurement instruments. Refined by customer feedback for years, these powerful and FREE software applications allow you to fully customize your project, from creating and modifying designs for your system board to custom scripting of instruments for capturing, recording, analyzing, and generating mixed signal and mixed domain waveforms.
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Mixed Signal Test Systems
MTS1000i
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
Production Test System
G3 Hybrid
The G3 Hybrid is a state of the art system for fast Production test throughput in DC test applications. The system combines the most versatile offerings of features in a single system, at the lowest cost. For devices requiring DC and Continuity test capability only, G3H is a very flexible cost-effective Production Test solution. This approach provides a DC test system with the capability to add logic resources (AC/SCAN) as well as analog resources for Mixed Signal. The HILEVEL G3H embraces low cost while supporting SCAN, giving you the ability to toggle every node in your chip.
-
product
A Popular Combination Of Flex 10 And Flex 20 In A Compact Footprint
Flex 30 ATE
A combination of both the Flex 10 and 20 system, the Flex 30 is floor mounted system that maintains a small footprint whilst offering that useful additional space. Generally it is fitted with either the G12 or G12X VPC interface allowing a large number of mixed signal connections to be routed to the test fixture.
-
product
GoldenGate RFIC Simulation Software
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
product
Mixed Signal Battery Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
product
Wafer Probe Test System
STI3000
The STI3000 is a wafer-level MEMS and mixed signal ASIC probe test system that combines several functional STI test equipment blocks for testing gyros, accelerometers, pressure sensors, microphones, resonators, and mixed signal ASICs.
-
product
SoC Test System
V93000 SoC / Smart Scale
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
product
JTAG Functional Test
JFT
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be trans...show more -
product
AMIDA 5000 Tester
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-spee...show more -
product
Build to Print
In today’s fast paced manufacturing environment, where time to market and cost competitiveness is key, having a manufacturing partner like ARC can be a valuable resource for your company. ARC has a build-to-print manufacturing capability with our unique ‘engineer-to-print’ philosophy to make sure precision manufacturing and final build accuracy is top priority for your module level or system level builds. ARC can support up to several hundred module level assemblies (CCA subassemblies, cabling, ...show more -
product
Engineering Support Platform
ESP
ESP, or Engineering Support Platform, is a low cost, powerful and versatile platform for the development, deployment and support of FPGA Applications. ESP is powered by DSX core, ARC’s core element for the development and deployment of digital and mixed signal systems. The standard system contains 2 custom FPGA system, often configured in combination where one acts as the application firmware, and the other is used for test. But the system is expandable and configurable in any combination to sol...show more -
product
Regenerative Battery Pack Test System
17020E
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery prot...show more -
product
Semiconductor Test System
TS-960e
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
product
Advanced SoC Test System
3680
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
product
VLSI Test Systems
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
In-Circuit Test System Repairs
Forwessun provides expert repair services for a wide range of Test Systems, helping you maintain optimal performance and extend the life of your equipment. Our team of skilled technicians quickly identifies and addresses issues, ensuring that your system is back in operation with minimal downtime. We handle both routine and complex repairs, offering comprehensive solutions to keep your systems running efficiently and reliably.
-
product
Communications Test System for Frontline Diagnostics
CTS-2750
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
Laser Diode Burn-in Reliability Test System
58604
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
product
Photodiode Burn-in Reliability Test System
58606
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
product
In-Line Test System
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
product
VLSI Test System
3380D
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
