- Virginia Panel Corporation
product
Tool, Locator, Thermocouple, ITA
910104135
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
product
Tool, Crimp, 75 Ohm Coax, Receiver and ITA, Hex Crimp
910104139
Used to crimp the ferrule on 75 Ohm contacts. Also included in tool kit p/n # 910102107.
-
product
Wire Crimp Pull Tester (Motorized)
WT3-201M
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
product
Tool, Locator, QuadraPaddle, ITA
910104140
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
product
Receiver, I2 Micro ICon, 120/12 Position Hybrid, For Crimp Contacts
310130105
The i2 Micro iCon receiver is a one piece connector capable of holding up to 120 Signal QuadraPaddle contacts and 12 Micro Coax or Micro Power. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is made for crimp contacts. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Tool, Crimp Die, Micro Coax, f/ RG 316 and RG 179 wire
910101133
Included in Tool kit 910101132.
-
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty cri...show more -
product
Thermocouple, Contact, Receiver, Chromel, Type K (°C)
610113131
Primary mating contact 610113133.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Wire Crimp Pull Tester (Manual)
WT3-201
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
product
Circular Connectors
Complete range of circular connectors with metal and plastic shells, and crimp and solder terminations for multichannel hybrid electrical/ optical insert arrangements, supporting a wide range of allowable contact voltages and currents, easy environmental sealing and rugged mechanical performance.
-
product
Thermocouple, Contact, ITA, Chromel, Type K (°C)
610113133
Primary mating contact 610131131.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Crimp Tester
M004
To calculate the crimp in yarn affected by knitting or weaving, to determine actual yarn usage.
-
product
Copper, Type T (°C) Contact
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Tool, Crimp, 20/26 GHz Coax Contacts, Receiver and ITA
910101124
Tool, Crimp, 20/26 GHz Coax Contacts, Receiver and ITA
-
-
product
Tool, Crimp, Mini Coax, ITA, 24-26 AWG Wire
910101118
Used to crimp Mini Coax ITA contacts to 24-26 AWG wire. Locator required.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body B...show more -
product
Tool, Locator, Thermocouple, Receiver
910104134
Used with Crimp Tool Part # 910101102 to crimp thermocouple receiver contacts.
-
product
Solar PV Test Equipment
Di-log offer a comprehensive range of Solar PV test equipment and tools to service the renewable industry. The range offers irradiance meters, DC current clamp , meters, crimp tools, roof surveying and protective gloves.
-
product
Thermocouple, Contact, ITA, Alumel, Type K (°C)
610113134
Primary mating contact 610113132.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Crimp Force Monitor
638007950
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
product
Connector, Cable Mount, 25 Pin 1.27mm Pitch Micro-D, Female, Crimp Pin
C025CFR-1CP-0A
This 25 pin micro-D connector is designed to allow users to directly terminate with crimped connections and is suitable for 26 AWG copper wire. Screwlocks are provided to secure the connector to its associated product. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Alumel, Type K (°C) Contacts
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
Crimp Tester
TF125
TESTEX Testing Equipment Systems Ltd.
Crimp Tester, to calculate the crimp in yarn affected by knitting or weaving by taking apart the yarn from a piece of given-length fabric, unbending it under given force and measuring its length, to determine actual yarn usage.
-
product
Hand Crimp Tool For Scorpion Connector Pins
C020AFR-2CP-2A-O
Hand operated crimp tool for pins fitted into a Scorpion connector housing.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of...show more -
product
160-Pin DIN41612 Connector, Crimp Pin, Female
40-960-160-F
Suitable for users to create their own cable assemblies, can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
-
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsChara...show more -
product
Tool, Crimp, Mini Coax, RG 316 and RG 178
910101115
Used to crimp the crimp ring to Mini Coax contacts.
