Filter Results By:
Products
Applications
Manufacturers
IC
circuitry in a chip.
See Also: Integrated Circuit, Chip, Digital IC Testers, IC Test, IC Clips, IC Probes
- TEAM SOLUTIONS, INC.
product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
product
SparkFun USB To Serial Breakout
FT232RL
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
-
product
ICs For Wireless Charging System
The feature of power receiving and charge/discharge system IC RAA457100 is integrated all functions needed for a wireless chargeing, rectification, charging control for small Lithium-Ion battery and top level of power-efficiency DC-DC converter in a singl chip as 3.22mm x 2.77mm small package.
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
SparkFun FTDI Basic Breakout
Beefy 3
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
product
High-Speed Precision SMU (100 FA, 60 V, 15 MSa/s)
PZ2121A
The Keysight PZ2121A is a high-speed precision source / measure unit (SMU) featuring best-in-industry narrow-pulse width, fast Digitizer Mode, and seamless current measurement ranging. It enables narrow-pulsed measurements and fast dynamic measurements with a wide dynamic range for a wide range of emerging applications such as vertical-cavity surface-emitting laser (VCSEL) optical devices, integrated circuit (IC) testing. In addition, its low measurement noise performance enables measurements with shorter aperture times, and its seamless current measurement ranging function enables a wide dynamic range and eliminates range change time, which improves test throughput.
-
product
Advanced Design System (ADS) Core
W2200BP
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
product
SparkFun Transceiver Breakout
MAX3232
The 'must have' IC for TTL/CMOS projects finally has its own breakout board! This is the RS232 converter IC that is capable of running at 3V and communicating with 5V logic.
-
product
Microtester Test Systems
With the micro probes and the fine-pitch adapters used on them, you are able to contact the finest test structures. E-tests, functional tests, IC tests or high-current tests are made to be affordable, efficient and with a short cycle time. With the integration of HF adapters we also enable the double-sided testing of HF substrates up to high frequency ranges.
-
product
Analog Custom IC Design Solution
Silvaco offer a full IC-CAD design flow including design capture, circuit simulation, layout design, physical verification, parasitic extraction and reduction, and post-layout analysis including statistical variation, IR-drop/EM.
-
product
40-Pin DIP-to-Socketable PLCC Adaptor
1111163
40 Pin DIP to Socketable PLCC Adapter. Can be used with Intel 80/83C652 and 80C251 microprocessors and any IC that follows standard DIP to PLCC pinout conventions. Allows user to switch package styles and avoid shortage problems. Designed to plug directly into your 44 pin PLCC socket.
-
product
Octal Test Site Handler
3180
The Chroma 3180 is a productive pick & place system for high-volume multi-site IC testing.
-
product
IC-3120, 1.91 GHz Intel Atom Quad-Core Processor, 2-GigE Port Industrial Controller
784959-01
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
product
Video Signal Distributor
MSDD-02D
MSDD-02D distribute the Analog Signal through the two (2) output without any diminution & distortion. The DDC line is designed with consisted of the two (2) channels in order to make the EDID data set up with the two (2) displays monitors at the one (1) same time. With two (2) generation by adapt as individually using the quick speed IC for exact output at the video data respectively, there is no signal deviation between input & output signal.
-
product
Boundry Scan Testers
Qmax Test Technologies Pvt. Ltd.
Boundary Scan Trainer Kit was developed by Qmax to provide user a good understanding and hands on the testing principals of boundary scan namely the scan chain test, interconnect test, non-BS functional testing of logic IC and cluster like a combinational or sequential circuits.
-
product
IC-3171, 1.9 GHz Intel Celeron Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784964-01
The IC‑3171 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3171 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
product
Failure Analysis
A partial list of our state of the art test equipment, applicable to these testing disciplines, will include the following: Two Scanning Electron Microscopes with EDS (SEM/EDS) Three Differential Scanning Calorimeters (DSC) Three Thermogravimetric Analyzers (TGA) Three Thermo Mechanical Analyzers (TMA) One Dynamic Mechanical Analyzer (DMA) Two Real-Time Fluoroscopic X-ray Systems, including a Microfocus System One Fourier Transform Infrared Microscope (FTIR) (capable of identifying a single particle of an unknown material) Two Ion Chromatographs (IC) (capable of identifying ionic impurities in ppm)
-
product
InfiniiVision Oscilloscopes
3000A X-Series
100 MHz to 1 GHz, DSO and MSO modelsView time-correlated digital content with16 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, IC, SPI, RS232 and more Protect your investment with full upgradability
-
product
Reticle Manufacturing
An error-free reticle (also known as a photomask or mask) represents a critical element in achieving high semiconductor device yields, since reticle defects or pattern placement errors can be replicated in many die on production wafers. Reticles are built upon blanks: substrates of quartz deposited with absorber films. KLA’s portfolio of reticle inspection, metrology and data analytics systems help blank, reticle and IC manufacturers identify reticle defects and pattern placement errors, thereby reducing yield risk.
-
product
Passive Probe, 20:1, 500 MHz, 1.3 M
N2875A
A compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the N2870A Series ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.
-
product
IC Tester
The Peritec adopted the NI products, to build in 1/10 the cost of the commercial product functions of the IC tester. It offers original brand as "ECOIC".IC tester on the market, yet very expensive that several tens of million, part of its function could only really used. Therefore, it possible to continue to build the only really necessary function in Peritec, we have created a mechanism to be completed at a lower cost and development, high-performance, short-term.
-
product
Wideband Transceiver IC
Analog Devices wideband transceiver ICs offer a complete, high performance RF and mixed-signal system on a chip. ADI’s ISM transceivers for short range wireless systems and wideband transceivers for wireless applications such as UMTS, LTE, and 3G/4G are highly integrated and deliver best-in-class performance and significant BOM savings.
-
product
PXIe Digital Stimulus/Response with PPMU: 250 MHz, 16 Channels
M9195B
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.
-
product
K-type Thermocouple to Digital Converter
THERMO K click
THERMO K click carries the MCP9600 IC from Microchip. Depending on the type of probe it uses the click can measure temperatures from −200 °C to +1372 °C.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Manual Test Adapter With Rigid Needles
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
product
Accelerometor, Gyro, Magnetometer Breakout Board
SEN-38001
The LSM9DS1 is a highly configurable, flexible and precise motion sensing solution from ST Microelectronics - the latest in a wide-ranging inertial product line. It integrates a 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer into a single IC , giving you a full nine degrees of freedom (9-DOF) in a tiny 3mm x 3.5mm package. Even with support components, square mounting pattern and connection breakouts for both SPI and I2C, this board is barely the size of a quarter.
-
product
Miniature IC Handler
3270
Chroma 3620 is an innovative system handler for high-volume multi-site IC testing, especially for CIS Testing, at the system level.
-
product
IC Testing System
Is a system for giving electrical signals to a semiconductor device to compare output signals against expected values for the purpose of testing if the device works as specified in its design specifications.
-
product
J1939 Simulator
DFLSJ1939BV1
The DFLSJ1939BV1 simulator is designed to simulate the truck or car''s ECU using J1939 protocol. It uses the DFL-SJ1939 IC with compact size. You can use free configuration software to customize the source address and 8 bytes of device name, and provide 2 extra customized PGNs. The configration software is free. You can download right now. New version 2.00 allows you to configure VIN#, and you can select J1939 DTC frame format from version1 to Version4. Furthermore, you can use our free PCTOOL software to change PGN value in real time.
-
product
IC Design & Verification
Mentor Graphics provides best-in-class products for IC design. Calibre for physical verification, extraction, resolution enhancement and mask data preparation, ADVance MS for analog/mixed-signal simulation and an integrated tool flow for custom IC design
