Filter Results By:
Products
Applications
Manufacturers
AMC
Advanced Mezzanine Card
-
product
Processor AMC, Intel® Xeon E5-2648L V4, PCIe Gen3 With PinoutPlus™
AMC750
The AMC750 is a Processor AMC (PrAMC) in a double module, full-size AdvancedMC (AMC) form factor based on the Intel® Xeon E5-2648L v4 which has 14 Cores @ 1.8 GHz. The module follows the AMC.1 and AMC.3 specifications.
-
product
Intel® 5th Generation Xeon Processor, AMC
AMC752
The AMC752 is a Processor AMC in a single module, mid-size based on the Intel® 5th generation Xeon (Broadwell). The efficient SoC design has low power consumption and integrated PCH technology. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
product
LS1046A Processor AMC, 10GbE
AMC709
The AMC709 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP LS1046A (quad core) processor. The unit provides 10GbE on Ports 4-7 and 8-11 per AMC.2.
-
product
PPC8315 Processor AMC W/ 2.5” SATA Drive
AMC715
The AMC715 is a Processor AMC (PrAMC) with an on board 2.5" SATA hard disk drive in a single-module, mid-size AdvancedMCTM (AMC) form factor based on the AMC.1, AMC.2 and the AMC.3 specifications. The module is ideal to be used for data flow management within a chassis. The AMC715 provides a low cost solution with an integrated high capacity disk. With a storage capacity of over 320 GB and data transfer rates of 150 Mbyte/s the AMC715 is the ideal AdvancedMCTM smart storage. The PCIe interface is configurable as Host or Agent mode. The module has 512 MB of DDR2 memory on board.
-
product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
product
Xeon E3-1125 Processor AMC, Dual SRIO
AMC722
The AMC722 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMCTM (AMC) form factor based on the Intel® Xeon™ Processor with an 8900 Series PCH.
-
product
For Conduction Cooled ΜTCA Chassis
UTC003
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
product
PrAMC Based On QorIQ P4040/P4080, 10 GbE, SFP+
AMC710C
The AMC710C is a flexible processor AMC for general purpose processing with the quad-core QorIQ P4040 with Data Path Acceleration Architecture intended for router and UTM (unified threat management) applications.
-
product
Intel® Xeon® Processor E-2176M AMC, 10/40GbE
AMC761
The AMC761 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E-2176M (Coffee Lake) with CM246 PCH. The processor base frequency is 2.7 GHz with max turbo frequency of 4.4 GHz. The module follows the AMC.2 and the AMC.3 specifications.
-
product
Xeon E5 Processor AMC, 40 GbE, PinoutPlus™
AMC751
The AMC751 is a Processor AMC (PrAMC) in a double module, full-size AdvancedMC (AMC) form factor based on the Intel® Xeon E5-2648L v4 which has 14 Cores @ 1.8 GHz. The module follows the AMC.2 and AMC.3 specifications.
-
product
36x36 Cross Bar Switch (CBS)
AMC241
The AMC241 is an AMC form factor with a 36x36 CBS which allows any of the 20 lanes from the backplane to be routed to the front. Since the CBS is agnostic to the protocol, any protocol such as PCIe, SRIO, 40GbE, 10GbE, GbE, Aurora, etc. could be routed between the backplane and the front panel.
-
product
Tilera GX72 Processor AMC, 72 Core
AMC740
The AMC740 is ideal for packet filtering, intelligent networking, multimedia, video transcoding, cloud and other applications. The device includes 72 identical processor cores (tiles) interconnected with Tilera’s iMesh™ on-chip network. Each tile consists of a full-featured, 64-bit processor core as well as L1 and L2 cache and a non-blocking Terabit/sec switch. The high processing density and high internal bandwidth of the GX72CPU make it ideal for intensive computing tasks.
-
product
Automated Monitoring of Airborne Molecular Contamination
AMC-Monitor T-1000
The all-in-one analyzer for FOUP, fab and clean-room environment AMC monitoring in the semiconductor industry. The AMC-Monitor is a modular and flexible platform for airborne molecular contaminations (AMC) monitoring in semiconductor applications such as: FOUP analysis with a focus on VOC and condensables incl. full integration with Pfeiffer Vacuum APA 302 pod analyzer. Clean-room monitoring in fabrication plants.
-
product
AMC For PCIe Bus Expansion
AMC113
AMC113 is VadaTech second generation PCIe expansion module. The AMC113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s other carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem.The AMC113 allows expansion among multiple μTCA chassis or
-
product
Cavium CN6880 Processor AMC
AMC738
The AMC738 utilizes the 32 Core Cavium Octeon II Processor that combines with a Xilinx V7 (XC7VX690T) FPGA to provide 100GbE via the CFP2 module. The CFP2 module could utilize 4 x 25 Gbps lanes or 10 x 10 Gbps lanes. The module follows the AMC.1, AMC.2 and AMC.4 specification. The FPGA has a single bank of 64-bit wide DDR3 memory.
-
product
Xeon E3-1125 Processor AMC, PCIe
AMC720
The AMC720 is a flexible processor AMC for general purpose processing. The AMC720 has quad-core Xeon and Linux support, it can act as system host and data processing engine. The dual front-panel GbE ports provide simple network connectivity, so while the unit is designed for embedded processing (i.e. typically without a monitor), it is straightforward to use with a virtual desktop on a remote PC/laptop for development and setup.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Software
LV-1553
The LV-1553 software is the interface to operate Abaco Systems' MIL-STD-1553 USB, XMC, PCIe, PCI, cPCI, ExpressCard, PCMCIA, Q104-Plus, AMC and VME boards with National Instruments’ LabVIEW graphical programming environment.
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Xeon E3 Processor, 10GbE, MTCA.4, Double Module, AMC
AMC725
The AMC725 is a Processor AMC (PrAMC) in a MTCA.4 double-module, mid-size AMC form factor. It features an Intel® Xeon E3 Processor with Cave Creek PCH, and on-board dual RAID options. The module provides PCIe Gen3 x4 or single x8 on ports 4-11 per AMC.1, dual GbE on ports 0 and 1 per AMC.2, and SATA on ports 2 and 3 per AMC.3. Dual 10 GbE ports are included on the front panel.
-
product
Intel® Xeon® Processor E-2176M AMC, PCIe Gen3
AMC760
The AMC760 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E-2176M (Coffee Lake) with CM246 PCH. The processor base frequency is 2.7 GHz with max turbo frequency of 4.4 GHz. The module follows AMC.1, AMC.2 and AMC.3 specifications.
-
product
Xeon E3 Processor AMC, 10/40GbE
AMC757
The AMC757 is a Processor AMC (PrAMC) in a single module, mid-sizeAdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E3-1505M v6 (Kaby Lake) with CM238 PCH. The processor base frequency is 3.0 GHz with max turbo frequency of 4.0 GHz. The module follows the AMC.2 and AMC.3 specifications.
-
product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
QorIQ P5040 Processor AMC, PCIe
AMC704
The AMC704 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5040 (quad core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
product
Intel Xeon E3 Processor AMC, PCIe Gen3
AMC756
The AMC756 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E3-1505M v6 (Kaby Lake) with CM238 PCH. The processor base frequency is 3.0 GHz with max turbo frequency of 4.0 GHz. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
product
QorIQ P5010/5020 Processor AMC, PCIe
AMC713
The AMC713 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the NXP P5010 (single core) or P5020 (dual core) processors. The unit provides dual x4 PCIe on Ports 4-7 and 8-11 per AMC.1 and the PCIe interface can be configured in Host or Agent mode.
-
product
QorIQ P204x Processor AMC
AMC711
The AMC711 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2040 or P2041. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as dual x4 (ports 4-7 and 8-11). The P2041 has option to have ports 8-11 as XAUI (10GbE). The AMC711 has up to 8GBytes of DDR-III memory with ECC.
-
product
Processor AMC Based On QorIQ T4241, PCIe
AMC703
The AMC703 is a Processor AMC (PrAMC) based on the Freescale QorIQ T4241 in a single-module, mid-size AdvancedMCTM (AMC) form factor based on AMC.1, AMC.2 and AMC.3 specifications.
-
product
Core I7 Processor AMC With PinoutPlus, PCIe
AMC728C
The AMC728C is a Processor AMC (PrAMC) in a double module, mid-size AdvancedMC (AMC) form factor based on the Intel next generation Core i7 Processor (Haswell) with QM87 PCH. The module follows AMC.1 (PCIe), AMC.2 (GbE) and AMC.3 (storage) specifications.
