Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI BRIC8 FIBO Matrix Dual 217x4 2pin brkout
40-592A-117
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
SparkFun Qwiic Micro:bit Breakout (with Headers)
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
product
SHDE9F-DE9F-FX Flexray Cable, No Termination, 1M
198290-01
9-Pin, Female D-SUB to 9-Pin, Female D-SUB FlexRay Cable - The SHD9F-D9F FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. The cable’s impedance is 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
-
product
PXI BRIC8 FIBO Matrix Dual 100x4 3pin brkout
40-592A-105
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
SparkFun Triple Axis Accelerometer Breakout
ADXL335
Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors - the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of +/-3g.
-
product
SparkFun Environmental Sensor
BME688 (Qwiic)
The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The gas sensor on the BME688 can detect a wide variety of volatile organic compounds (VOCs), volatile sulfur compounds (VSCs), and other gases such as carbon monoxide and hydrogen in the part per billion (ppb) range. Combine that with precise temperature, humidity, and barometric pressure and the BME688 can work as a completely standalone environmental sensor all in a 1in. x 1in. breakout!
-
product
SparkFun Humidity Sensor Breakout
SHTC3 (Qwiic)
Looking to keep a log of the climate in your greenhouse, create a humidor control system or want to track temperature and humidity data for a weather station project? The SparkFun SHTC3 Humidity Sensor may be the perfect option for you! The SHTC3 is a low cost, easy-to-use, highly accurate digital humidity and temperature sensor. The SHTC3 communicates via I2C so, as you can tell by the name, we have broken out the pins on the sensor to Qwiic connectors so you can easily connect it to SparkFun's ever growing Qwiic Ecosystem.
-
product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
product
Camera Link Breakout Box
CLB-501B
The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.
-
product
SparkFun Atmospheric Sensor Breakout
BME280 (with Headers)
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
-
product
Modular Breakout System 50-Pin D-type Plugin Module for 40-198
95-198-001
The 95-198-001 Plugin Breakout Module is designed to be fitted to a PXI 40-198 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
product
IntellaView
EdgeSwitch
The IntellaView EdgeSwitch is a high-density 1RU system with 32 ports of 40G / 100G Ethernet capability, while the breakout mode can support up to 128 ports of 10G / 25G. The EdgeSwitch enables efficient traffic aggregation, filtering, load balancing, tunnel management, and port tagging standalone or as part of a larger visibility solution.
-
product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-H
Breakout board for the Sensirion SHT31-DIS-B. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
product
SparkFun Level Shifting MicroSD Breakout
The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD library’s top speed on a 5V system. With this small breakout board, that is not much bigger than your fingernail, adding mass storage to your project will never be easier.
-
product
(ITA), Breakout Box & Fixtures
WinSoft provides a wide range of Interface Test Adapters (ITA) and test fixtures to meet the most challenging functional test and signal conditioning requirements. This includes high frequencies, voltages and current.
-
product
BNC-2090A, 16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block
779556-01
16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block - The BNC-2090A is a desktop or rack-mount analog breakout terminal block that you can connect to compatible PXI Multifunction I/O Modules. The terminal block features 16 analog input (AI) BNC connectors for eight differential or 16 single-ended channels. The BNC-2090A also features two analog output (AO) BNC connectors, two user-defined BNC connectors, one analog programmable function input (APFI) BNC connector, one PFI BNC connector, and two 68-pin I/O connectors for DAQ device connection. Additionally, the BNC-2090A features spring terminal block for digital I/O and PFI connections.
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
SparkFun Distance Sensor Breakout
4 Meter, VL53L1X (Qwiic)
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 40mm to 4m away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
product
HV BM Split Modules
The HV BM Split Modules use the proven technology of the HV Breakout Modules for fast and precise measurement of internal conductor current, voltage and power even in confined spaces. HV BM Split Modules can be used to perform measurements in HV power cables or also on busbars.
-
product
SparkFun Transceiver Breakout
NRF24L01+
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice!
-
product
SparkFun RGB Light Sensor
ISL29125
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity of the general red, green, and blue spectrums of visible light while rejecting IR from light sources. You can then use these color sensor readings for the purposes of logging and finding patterns, or creatively calculate and make control decisions in your electronic projects.
-
product
SparkFun GNSS-RTK Dead Reckoning Breakout
ZED-F9K (Qwiic)
The SparkFun ZED-F9K GNSS Breakout is a high precision, sensor fusion geospatial board with equally impressive configuration options and takes advantage of u-blox's Automotive Dead Reckoning (ADR) technology. The ZED-F9K module provides a highly accurate and continuous position by fusing a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data, and GNSS measurements.
-
product
SparkFun Thermocouple Breakout
MAX31855K
The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a 'hot' end and a 'cold' one). Once this is achieved, a voltage potential is formed and current flows. The SparkFun Thermocouple Breakout takes a standard Type-K thermocouple in one end, digitizes the temperature measured and sends that data out the other end via a SPI interface, thereby interpreting the data and translating it for you to read!
-
product
SparkFun Digital Temperature Sensor Breakout
TMP102
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn't require much setup.
-
product
SparkFun USB MicroB Plug Breakout
We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out all five pins with a vertical microUSB connector for your prototyping needs.
-
product
Breakout Tools
Quickly test and troubleshoot harnesses, engine control modules or sensors by connecting a Breakout Box onto your system.
-
product
15 Pin Breakout Interface
VSI-Breakout-15
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Telecom & Data Test
Electro Standards Laboratories
iagnostic tools such as Breakout Boxes/Interface Analyzers designed for use at the data interfaces of modems, multiplexers, terminals, and computers. Electro Standards Laboratories' Series of Breakout Boxes/Interface Analyzers are virtually indestructible and compatible with RS232, HSSI(SCSI-2), EIA/TIA RS530 interfaces.
