Filter Results By:
Products
Applications
Manufacturers
Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
- Pickering Interfaces Inc.
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PXI 4 Slot BRIC Module, 1 Resource Distributor, 1 Bus Matrix Inputs
40-569B-011
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-011 is a 4 slot module fitted with 1 Bus Matrix Inputs card and 1 Resource Distributor card.
-
product
Low-Profile High-Performance IEEE488 GPIB Interface for PCI Bus
LPCI-3488A
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
40-203-002
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
Ethernet Gateway for Woodward Easygen Genset Controls and LS-5 And DTSC-200 Controls
ESENET
ESENET is an Ethernet gateway specifically designed to interfaceWoodward's Easygen series genset controls with Modbus/TCP networks. It interfaces via the load sharing CAN bus with the Woodward controls.
-
product
PXI/PXIe
Four independent delay channels 1 ps resolution < 50 ps rms jitter >20 second delay range Four auxiliary delay channels 5 ns resolution < 100 ps rms jitter >20 second delay range Front panel or PXI bus PXI 3U, 1 slot, compact packaging更多其他产品内容可咨询：400-621-8906
-
product
PXI 8-Slot BRIC Matrix, 184x8, 1-Pole (4 sub-cards) Dual Bus
40-560B-121-184X8-M
The 40-560B-121-184x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
product
Profibus Gateway for Woodward Easygen Genset Controls and LS-5 Controls
ESEPRO
ESEPRO is a Profibus gateway specifically designed to interface Woodward's Easygen series genset controls with Profibus-DP networks. It interfaces via the CAN bus with the Woodward controls and is easy to configure using standard Profibus configuration tools like Simatic Manager.
-
product
16 Bit Waveform Generator
PA72G16400
The PA72G16400 is a 16-bit arbitrary waveform generator, capable of generating waveforms at speeds up to 400Msps. The high resolution and the high sample rate allows generating signals with very low quantization noise levels. An onboard offset voltage source allows generating offset signals while maintaining optimal utilization of the DAC’s digital range. With the 8MWord of memory, there is lots of room for uploading several different patterns, allowing switching patterns with minimal bus communication.
-
product
Mini Munitions Store Interface
MMSI
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
product
Linear Power Supplies Precision, GPIB or Local Control, Ultra Low Ripple/Noise
Series ATE-DMG
Kepco's 1000 watt instrument-grade digital power supplies, Series ATE-DMG, are linear low-noise power supplies designed to respond very quickly and precisely to voltage and current setting instructions delivered interactively by the GPIB (IEEE 488.2) or from a front panel keypad. When programmed from the bus, the ATE-DMG power supplies respond to the SCPI (Standard Commands for Programmable Instruments) common language for instruments used in an automatic test system.
-
product
PXI Express Board Virtex-5 ADC Module
SMT791
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
-
product
4-CH Analog Output Module
HSL-AO4-U
The HSL-AO4 offers four analog output channels with a high drive capacity based on the HSL bus. The HSL-AO4 also features 16-bit resolution and offset/gain calibration to minimize the power-on 0-voltage drift to meet precise analog output requirements.
-
product
Thunderbolt V-600 Board 4-Slot
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
-
product
Acquisition Of 8 Displacement Transducers
APCI-3701-8
PCI interface to the 32-bit data bus Acquisition of 16 or 8 inductive displacement transducers (Half Bridge, LVDT) 8 or 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 3UVPX
Model 54851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Compatible with several VITA standards including: VITA 66.5, VITA 67.2 and VITA 67.3C- Supports VITA 49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Industry Pack Carriers and Digital I/O
CPCI-2IPC-6U
The CPCI-2IPC-6U module provides a high performanceflexible I/O scheme, that supports industry standard IndustryPacksÔ. For application requiring high performance, highdensity I/O or unique combinations, the CPCI-2IPC-6U is theperfect solution. The Local DSP’s can be used to simplymove data to and from the CPCI bus or provide localprocessing functions such as local PID controls, FFT’s, digitalfiltering, etc.
-
product
16 or 32 channel Digital to Analog Converter
LS-71-P
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
product
6U Power Supply Mainframe
GX7400A
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
product
Express Card
DAS-429ExCARD/RT10
Both cards contain 64 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table.The card's small size (54 millimeter wide) and suitability for Express Card compatible notebook computers make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Logic Analyzer
GoLogicXL-36
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
product
CPCI timing plug-in
CPCI-SyncClock32
The CPCI-SyncClock32 from Brandywine Communications provides precision time with zero latency to the host computer over the CPCI bus in the 3u form factor. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or Have Quick.
-
product
Arbitrary Waveform Generator
SDG7000A
SIGLENT’s SDG7000A is a family of dual-channel Arbitrary Waveform Generators that feature up to 1 GHz bandwidth, a maximum sample rate of 5 GSa/s, and 14-bit vertical resolution. It can generate arbitrary waveforms point by point with a maximum 2.5 GSa/s sample rate and vector signals with a maximum of 500 MSa/s. It also has the ability to generate a variety of signals such as continuous wave, Pulse, Noise, PRBS patterns, and a 16-bit digital bus. It supports the generation of complex signals such as modulation, sweeping, bursting, and dual-channel copying/coupling/tracking and superposition. The outputs are user selectable for differential or single-ended connections and support a maximum output range of ± 24 V. The instrument can ensure a large amplitude under high-frequency which eliminates an external power amplifier in some applications and addresses a wider range of requirements.
-
product
PCI to PMC Adapter / Carrier
PCIBPMCx2
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIBPMCx2´s two slots; a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card.
-
product
CAN Bus & ARINC-825 (825CAN)
The 825CAN module is an intelligent multichannel ARINC 825 (CAN bus) interface module for the multiprotocol Excalibur 4000 & 8000 family of carrier boards. The module supports up to ten ARINC-825 channels. In receive mode, the module stores all or selected messages with status and Time Tag information appended to each message. In transmit mode, the module operates via a transmit Bandwidth Frame which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
product
Chrysler CCD Vehicle Bus Comms PC Card
SL100
The SL100 uses a standard 16450 UART with baud rate settings that makes it capable of communicating with a Chrysler CCD Vehicle bus. The SL100 uses a protected interface driver chip, as prescribed by the bus specification, to connect with vehicle peripherals in a robust and highly noise immune way. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
product
Space
Honeywell Aerospace Technologies
Honeywell’s space portfolio is made up of highly innovative products that span human space missions, launch vehicles, microelectronics and satellite payload and bus technology.
-
product
PXI Matrix Switch: 8x32, 1-Wire, 100Vrms/2A, Armature Relays
M9122A
The M9122A is an 8x32 full crosspoint switch matrix offering high-voltage switching in a high-density PXI module. This module allows for higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This module is configured with a common ground. The durable armature switches are capable of switching up to 100Vrms, with up to 60W of power. The 8-wide bus can be used to route signals between your instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
product
8-Slot, 3U PXI Chassis
GX7800
The GX7800 is a compact, 8-slot PXI chassis that can accommodate up to 7 instruments as well as an embedded 3-slot PXI controller or an external bus controller such as a MXI interface. The GX7800’s compact 3U form-factor occupies only 9 x 18 inches of bench space, making it ideal for benchtop or space constrained applications.
-
product
PCI Express Cable Extender
SKU-016-XX
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
