-
product
Phase Splitter Comb Generator
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
product
Hexagonal Wet Film Combs (Stainless Steel)
112 & 3236
These hexagonal precision formed stainless steel wet film combs are long lasting, reusable and supplied in a range of thicknesses measuring up to 3,000μm (120mils).
-
product
Wet Film Combs (Stainless Steel)
Elcometer 115
Four separate thickness ranges are available up to a maximum of 1,250μm or 50mils and are manufactured to an accuracy of ±5% of marked value or ±3µm (0.12mil), whichever is greater.
-
product
Add-ons For Metrology
We offer add-on products for Optical Frequency Combs and metrology applications. These include heterodyne photodetectors (BDU), and highly stable RF oscillators, just to name a few.
-
product
Long Edge Wet Film Combs (Stainless Steel)
3238
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-01
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channe...show more -
product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-02
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channe...show more -
product
Pressley Fiber Bundle Strength Tester
F215
To determine the tensile strength of natural fibers. Includes 1 pair clamps and spacer, torque vice and wrench, cutter, comb and tweezers. A 5mg x 0.01mg capacity balance is required but not included.
-
product
Comb Generator
CG01
The main application of Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble shooting Open Area Test Sites(OATS).An OATS must be completely calibrated before it is put into service. reference signal source Noise Generators Signal Generators
-
product
Frequency Synthesiser
RA062-F2
The RA062-F2 is a multiple LO module used to generate three pairs of LO signals, each pair being phase matched in order to provide the capability to drive two phase and amplitude matched, high sensitivity narrowband receivers such as might be required for an EW receiver system with DF functionality.The Stepped Frequency Synthesiser is based upon Direct Frequency Synthesis, DFS, whereby the 1GHz input reference signal is multiplied, filtered and mixed to generate a given number of isolated and fi...show more -
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Comb Generator
WJ10-50A
Comb Generator model WJ10-50A with Broadband Antenna. Frequency Range 10 MHz - 11.0 GHz with two frequencies step option; 10/50 MHz
-
product
Dual Channel Synthesizer
SYNTH1400X2
Convenient Ethernet ApplianceControllable from anywhere by computer or mobile device100KHz to 1400MHz frequency tuning in 190 picoHertz stepsTwo synthesizers are independently programmableBoth synthesizers track due to common reference16-bit phase tuning resolution12-bit amplitude scalingProgrammable modulusAutomatic linear and nonlinear frequency sweeping capabilitySwitchable frequency/phase-offset profilesUltra-low phase noiseOptional pulse comb generator output
-
product
Comb Generators
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
-
product
Comb Generator
WJ10-100A
Comb Generator model WJ10-100A with Broadband Antenna. Frequency Range 10MHz - 11 GHz with two frequencies step size option; 10/100 MHz
-
product
Reference Radiators / Comb Generators
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Sideband Bus Protocol Analyzer
FS2700 DDR5
The FS27xx DDR5 Sideband Bus Protocol Analyzer is the latest DDR5 tool from FuturePlus Systems. FuturePlus has taken the complexity of 8 different JEDEC specifications and ported them into this very useful tool. DDR5 Validation Engineers and system integrators will not have to comb through complex specifications defining thousands of bits and register addresses. The tool takes care of this. Please request our data sheet for more information.
-
product
Comb Generator
WJ10-25A
Comb Generator model WJ10-25A with Broadband Antenna. Frequency Range 10 MHz - 8 GHz, with two frequencies step size option; 10/25 MHz
-
product
NI-9252, ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786783-01
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
Vector And Scalar Mixer / Converter Measurements
S95083B
The Keysight S95083B measurement software includes the scalar mixer / converter plus phase (SMC+Phase) measurement class. It provides fully calibrated conversion gain / loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C / F / G comb generator and an external DC power supply. A vector mixer characterization (VMC) is also included for measuring group delay of frequency-converting devices. VMC can be used to characterize a user-supplied calibration mixer.
-
product
Quantum Laser Systems
By combining the Optical Frequency Comb and multiple ultrastable frequency stabilized lasers in a transportable, rack based system Menlo Systems offers a complete laser system for most demanding applications like optical clocks, quantum computing, and quantum physics experiments based on cold atoms, molecules and ions. The customer can configure the system in terms of laser wavelengths, laser power and frequency accuracy so that it is optimally matched to the application.
-
product
Uncured Powder Film Comb
155
This enables the application system to be set up and fine tuned prior to the curing process. In turn, this will reduce the amount of scrap and over-spray.Place the comb into the powder and slide the comb along the surface. The measurement points (or teeth) are pointed and allow the powder to flow around them.
-
product
NI-9252 , ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786782-01
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a … number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
Radiating Comb Generators
TBCG1
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Mechanical Products
*99 types of pin cut data are stored in the backup RAM and can be recalled whenever necessary.*Inputting unnecessary pins and cutting to the specified size is easy and clear as it is done while watching the pins appear on the LCD (liquid crystal display screen).*Changing to a different pitch can be done in a short time by simply replacing the sprocket and comb teeth.
-
product
Integrated Connection Technology
Compact design - Connection points for bridge combs - Solder-free circuit board contact - Plug -in connectors for interchangeable modules, such as small relays