Filter Results By:
Products
Applications
Manufacturers
-
product
Building Monitoring
Crackmeter
The system consists of two plates that overlap for part of their length. One plate is calibrated in millimeters and the overlapping plate is transparent and marked with a hairline cursor. As the crack width opens or closes, one plate moves relative to the other. The relationship of the cursor to the scale represents the amount of movement occurring. These gauges are monitored over time, whilst being kept as far away from human disturbance as possible, to develop an understanding in the width and direction of movement of the crack.
-
product
Sand & Dust Test
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
product
Special Use Sensors
Structures can, and do, break, and this may be important and sometimes dramatic. It’s critical to determine whether a particular object made from a particular material can carry a particular load. If a true stress is ignored, the cost of not acting is usually far higher than the cost of dealing with the problem earlier. A good example is in ductile materials. The crack moves slowly and is accompanied by a large amount of plastic deformation around the crack tip. The crack will usually not extend unless an increased stress is applied. Geometrical irregularities, such as cracks, sharp corners and holes – which many times are ignored – may raise the local stress.
-
product
Outsole Belt Flexing Tester
UI-FT36
Outsole Belt Flexing Tester, which is also named as Bata Belt Flex Tester, is used to test sole flexing resistance ability. Belt Flex Tester is designed and applicable to SATRA TM133 Resistance to crack initiation and growth–belt flex method.
-
product
Metallic Corrosion Detector
Xiamen IDEA Electronic Technology Co., Ltd.
Portable Metal Corrosion Detectors , is used for testing the steel pipe corrosion, stainless-steel tube corrosion and sheet materials corrosion, which can tell the high rate color LCD, can adjust phase, gain and testing frequency ,can used for testing the different metallic corrosion , such as corrosion pit, fluid dust scouring thickness reduction,crack, oxygen corrosion and hydrogen corrosion. has English and chinese operating interface, simple and visual operation.
-
product
Demattia Flex Tester
UI-FT33
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
product
High-Power Cinema Subwoofer
X-800C
The X-800C subwoofer supports full-range cinema speakers with 1,240 watts of visceral low-end punch, for bone-shaking bass in every seat. It delivers supreme power, intelligibility, and clarity in the 20–200 Hz range—reproducing the deepest rumbles and the sharpest thunder cracks with ease.
-
product
Inspection System
X-eye 7000B
Appropriate for the inspection of medium•large size components and detection of surface structure and defects (inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's significantly reduced and long-term use possible with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
product
Acoustic Emission Sensors
Acoustic wave (acoustic emission) sensors are the ceramic piezoelectric transducers converting the mechanical elastic acoustic waves generated in the material (e.g. elastic waves occur when a material cracks, wears, deforms, or corrodes) to electrical signals. The electrical signals are then amplified and filtered by a preamplifier and then transmitted to a special acoustic emission acquisition instrument for further data processing and analysis.
-
product
Soldering Inspection Video Microscope
MS-1000
The MS-1000 is a highly portable microscope for exclusive use with BGA, CSP, and QFP. It is highly efficient in inspecting portions which cannot be inspected by the X-ray inspection method.Specifically, it is efficient for inspecting the following conditions: fillets of soldered balls, melted condition of soldered parts, cracks, defective soldering, etc.
-
product
Front and Back Side Topography Defect Detection
LIGHTsEE
High throughputNanometer range vertical sensitivitySimultaneous double side inspectionNanotopography and Topography measurementDetection of Slip lines, particles, Hairline cracks, SOI voids, Comets, EPI defects…Compliant with thin or thick wafers, taiko wafers, highly warped wafers
-
product
Moisture Meters
Moisture can be found in any material. Even materials considered to be dry have a minor amount of moisture. An imbalance of moisture, whether it be excessive moisture or too little moisture, can cause problems ranging from undesired mold and bacteria growth to cracks and defects. To avoid a moisture imbalance, it is essential to monitor moisture content with a moisture meter that returns accurate and reliable measuring results. A moisture meter can measure the moisture content of everything from the air (relative humidity) to construction and building materials (concrete, wood) to biomass and agricultural products (hay, straw, grain, corn, beans, pellets) to solid waste (pulp, slurry) and beyond. Many moisture meter devices can also measure temperature. The moisture measurement range of each moisture meter varies depending on the model. Some moisture meter products take moisture measurements, store the moisture measurement data to an internal memory or SD cad, and allow the stored moisture measurement data to be transferred to a computer for detailed analysis by means of an evaluation software. PCE Instruments' moisture meter products come factory calibrated. ISO calibration certificates are available optionally for purchase as accessories to most moisture meter models. An ISO calibration certificate may be important to your company in meeting specific quality standards.
-
product
Non Destructive Testing (NDT)
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
product
X Ray Flaw Detector
A non-destructive testing (NDT) device used to inspect materials for internal flaws or defects such as cracks, voids, inclusions, and weld discontinuities.
-
product
Fatigue Crack Growth Testing Module
Resistance to fatigue, ageing and crack growth are major issues for rubber like materials. Current commercial methods for crack growth testing have been restricted to time to failure test.
-
product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
product
Portable Utrasonic Flaw Detector
MFD510B
Mfd510b portable ultrasonic flaw detector can test, orient, evaluate and diagnose various flaws such as unmelted weld joint, unpenetrated weld joint, crack, inclusion, air hole in worklpiece’s interior swiftly and accurately without any destruction. It is widely used in fields of power engineering , boiler pressure vessel , steel construction , war industry , aeronautics , rail transportation ,auto and machinery etc. It is the essential instrument in ndt industry.
-
product
Crack Width Ruler
143
Elcometer 143 Crack Width Ruler is a simple gauge that has been designed to provide inspectors with a low cost alternative to a graduated microscope for determining the width of a crack in concrete or other building materials.
-
product
High Temperature Clip-On Gages (700 C)
Model 7641
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
product
Ultrasonic Immersion Probes
SONOSCAN I
The SONOSCAN immersion transducers for Non-destructive Testing (NDT) are mainly used to test metals and plastics for the smallest material defects. For example, binding defects, welding defects or cracks and pores in metal parts can be detected. The powerful, robust ultrasonic probes can be connected to all common ultrasonic testing devices. Due to variable designs and sizes, the immersion probes guarantee optimal use. In addition to ultrasonic standard pobes, we also offer customized transducers according to your individual specifications.
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
product
Ultrasonic Flaw Detector
MFD550B
Based on ultrasonic principle, digital ultrasonic flaw detector MFD550B can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it show the defect clearly under the dim light and strong sunlight environment. 0-9999mm measuring range can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium ion battery module，it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways inone body, customers with different habits can operate it freely. With comprehensive performance self-checking function, it can automatically generate test reports and support for many languages. With high cost performance, it is the smart choice for the practical economic model of ultrasonic testingequipment.
-
product
Class 1 Sound Pressure Level Meter
Castle Sonus GA116B
The entry level of the Castle Pocket Range of Sound Level Meters is the SONUS B(GA116B ), a feature packed, pocket instrument that is fully compliant with IEC 61672-1:2013. This meter gives simultaneous sound pressure (Lp) and peak (Cpeak) measurement for a multitude of tasks including initial spot-check assessments to the Control of Noise at Work Regulations 2005. It has a high-specification measurement microphone and is cased in tough, crack resistant ABS plastic.
-
product
Luminescence Defect Inspection System
INSPECTRA® PL Series
This system uses luminescent images created using photoluminescence (PL) to perform high-speed, high-sensitivity automatic inspection for crystal defects, cracks, and luminescence defects which cannot be detected with conventional visible light surface inspection!
-
product
Video Endoscope Cameras
PeakTech Prüf- und Messtechnik GmbH
Is used to locate objects such as connection terminals, electronic components, break points, constrictions, cracks or components at hard-to-reach, hidden locations. This video endoscope camera offers a variety of excellent technical properties, such as the detachable monitor connected by video cable or the high-resolution camera with 6 dimmable LEDs for lighting, which can take photos and videos.
-
product
Material Testing
*Abrasion Testing*Adhesion Testing*Brittleness Temp.*Bursting Strength*Coating Testing*Coefficient of Friction*Compression Testing*Compression Set*Dart Drop Testing*Density Determination*Fatigue Testing*Fiberboard Testing*Flammability Testing*Flexural Testing*Foam Testing*Hardness Testing*Heat Deflection*Hydrostatic Testing*Impact Testing*Life Cycle Testing*Melt Index Testing*Plastic Testing*Ply Separation*Resin Content*Rubber Testing*Shear Strength Testing*Stress Crack Testing*Tear Testing*Temperature Testing*Tensile/Elongation*UV Exposure*Water Absorption*Wood Testing
-
product
Safety Footwear Impact Tester
SG-P11A
This machine, incorporating a steel striker adaptered to fall freely on vertical guides from a predetermined height to give the required impact energy to the toe of safety footwear for measuring the degree of the dent. In addition, the toecap should not develop any cracks on the test axis with go through the material.
-
product
Ultrasonic Dual Element Probes
SONOSCAN T
The ergonomic dual element probes for Non-Destructive Testing from the SONOSCAN Series comply with the DIN EN 12668-2 Standard and can be used to test metals, plastics and ceramics for imperfections such as cracks, inclusions, blowholes and other discontinuities. The transmitter-receiver probes manufactured in Germany are powerful, robust ultrasonic transducers which are compatible with the ultrasonic flaw detector SONOSCREEN ST10 or the thickness gauge SONOWALL 70.
-
product
Sapphire Defect Laser Probe and Glasses
LP-100
Easy to use and portable■ low price with long lifetime■ can be used to detect many defects, like micro crack, bubbles, impurity, crystal subgrain■ When the laser go though the crystal, if it is monocrystal the light should be scattering, in macro it should be white.
-
product
Strength Meter
NOVOTEST IPSM-U+T+D (Pulse Velocity Tester)
The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete). Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).
