Filter Results By:
Products
Applications
Manufacturers
Data Acquisition Systems
sense, log and store information. AKA: DAS
See Also: Data Acquisition, PCI Data Acquisition, DAQ
- Pickering Interfaces Inc.
product
PCI Very High Density Multiplexer, Quad 24-Channel, 2-Pole
50-671A-022-Q/24/2
The 50-671A-022-Q/24/2 is a very high density PCI multiplexer in 24-channel 2-pole format with 4 separate banks. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI High Density Multiplexer, 20-Bank, 4-Channel, 1-Pole (SP4T)
40-615A-013
The 40-615A-013 is a 20-bank, 4-channel, 1-pole (SP4T) MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
cRIO-9054, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller
786425-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 4-Slot CompactRIO Controller - The cRIO-9054 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
PXI Very High Density Multiplexer, 49-Channel, 4-Pole
40-675A-002-49/4
The 40-675A-002-49/4 is a 49-channel, 4-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
PXI Dual 16x8 Matrix, 1 Pole Switching
40-532-021
This high-density reed relay matrix with 256 crosspoints. This model is configured as a Dual 16x8, model 40-531 is configured as a 32x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version can be used for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
4-CH 16-Bit 2MS/s Simultaneous-Sampling USB DAQ Module
USB-1210
The USB-1210 is a 16-bit high-speed USB 2.0-based DAQ module equipped with 4 analog input channels providing simultaneous sampling at up to 2MS/s per channel. The USB-1210 delivers high accuracy and excellent dynamic performance at maximum sampling rates, and flexible trigger functions. In addition, onboard 64M samples FIFO ensures no data loss during acquisition even when CPU or system loading is heavy.The USB-1210 is USB bus-powered and equipped with removable screw-down terminals for easy device connectivity. The attached multifunctional stand can be used for desktop, rail, or wall mounting. Suitable for high-speed data acquisition, laboratory and medical research, the USB-1210 provides a reliable measurement solution at an affordable price.
-
product
Single 8x8 1-Pole High-Density PXI Matrix Module
40-520-204
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Push Pull Testers
Lever-operated manual systems enable rapid push/pull testing up to 220 lbf.Wheel-operated manual systems enable slower, more precise movement with the hand wheel up to 750 lbf.Motorized push/pull testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement up to 1100 lbf.All push/pull testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
product
Dataloggers and Multichannel Recorders
SA analog data acquisition system 32 is designed to measure, treat, monitor and record the parameters from analog sensors of 32 channels in 2 son and 8 channels in 4 son.
-
product
Rugged Data Acquisition Systems
Our team of engineers have decades of experience in performing structural testing in the aerospace, off highway, automotive, construction equipment, pulp & paper, and utility markets. We have used our testing expertise to develop a line of Rugged Data Acquisition (RAC) Systems that perform under harsh testing conditions.
-
product
Isolated Digital Expansion Board
MSXB 078
The Microstar Laboratories Isolated Digital Expansion Board, part number MSXB 078, provides isolated digital expansion for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing errors from high-channel count digital I/O.
-
product
PXI 2A Multiplexer, 8-Bank, 16-Channel 1-Pole
40-614-003
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
MicroTCA Systems
Pixus Technologies offers customized MicroTCA® shelves and system solutions. With expertise in xTCA systems, along with backplane and cooling specialists, Pixus will help you create a winning µTCA design. MicroTCA is a modular, open standard for building high performance switched fabric computer systems in a small form factor. MicroTCA systems utilize standard Advanced Mezzanine Cards (AMCs) which provide processing and I/O functions. MicroTCA targets smaller telecom systems at the edge of the network, as well as mobile, military, telemetry, data acquisition, and avionics applications.
-
product
PXI Multiplexer, Dual 16-Channel, 2-Pole
40-630A-022-D/16/2
The 40-630A-022-D/16/2 is a dual 16-channel, 2-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 57851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Synchronization and Distribution Amplifier - PCIe
Model 7892
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
product
48-Channel Seismometer
FlashSeis48
ZZ Resistivity Imaging Pty. Ltd.
48 channel seismic data acquisition system.
-
product
Powered VXS Crates
6U VXS 6023-JL
The WIENER VXS 6023 crate series adds high performance Switch Fabrics according to VITA 41 specification to VME based systems. Designed primarily for high speed applications in data acquisition, as well as military / aerospace test and instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
product
IC-3120, 1.91 GHz Intel Atom Quad-Core Processor, 2-GigE Port Industrial Controller
784959-01
The IC‑3120 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3120 offers two Gigabit Ethernet ports with Power over Ethernet (PoE) technology, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
product
4-Channel 200 MHz A/D with Multiband DDCs, Kintex UltraScale FPGA - PCIe
Model 78862
Model 78862 is a member of the JadeTM family of high-performance PCIe boards. The Jade architecture embodies a new streamlined approach to FPGA-based boards, simplifying the design to reduce power andcost, while still providing some of the highest- performance FPGA resources available today. Designed to work with Pentek’s new NavigatorTM Design Suite of tools, the combination of Jade and Navigator offers users an efficient path to developing and deployingFPGA-based data acquisition and processing. The 78862 is a multichannel, high-speed data converter with programmable DDCs (digital downconverters). It is suitable for connection to HF or IF ports of a communications or radar system. Its built-in datacapture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
-
product
SIRIUS MINI
SIRIUS MINI 4-channel DAQ Vibration MeterSmall and highly portable, USB powered data acquisition system ideal for acoustic, vibration, and rotating machinery analysis.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Data Acquisition Switch System
M300
No matter the product performance test in the R & D stage or the automatic test in the production process, for the application of multiple test points and multiple signal measurement, the M300 series data acquisition / switch system with modular structure combines the precise measurement function with the flexible signal connection function, and can provide a wealth of test measurement solutions.
-
product
JadeFX FlexorSet 4-Ch 16-bit: 500 MHz A/D & 2 GHz D/A - 3U VPX
Model 5983-324
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex UltraScale FPGAs- Four 500 MHz 16-bit A/Ds- Four digital upconverters- Four 2 GHz 16-bit D/As (500 MHz input sample rate, 2 GHz output sample rate with interpolation- 4 and 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system referencePCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and sychronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)
-
product
Sensing Analysis Software
ENLIGHT
A single suite of tools for data acquisition, computation, and analysis of optical sensor networks based on the HYPERION system.
-
product
Kollisionsvermeidungs-Radarsensor
OndoSene reach WA (D)
Mit seinem breiten Erfassungsbereich eignet sich der OndoSense reach WA (Wide Angle) besonders gut zur Erkennung von Hindernissen wie Fahrzeugen, Personen oder Objekten sowie zur Positionierung von Robotern und Maschinen. Er erfasst statische und bewegte Objekte selbst im Nahbereich ab 0,1 Metern und ist aufgrund seiner sehr kleinen Bauform auch bei beengten Platzverhältnissen problemlos integrierbar. Mit bis zu 4 einstellbaren Sensorzonen ist der OndoSense reach WA ideal für das flexible Monitoring von Sicherheitsbereichen oder die Kollisionsvermeidung mobiler Roboter oder anderer Fahrzeuge geeignet. Dank innovativer Radartechnik detektiert der Radarsensor Objekte jeglicher Beschaffenheit auch im Außenbereich oder in schwierigen Umgebungen mit Schmutz, Rauch, Dampf, Regen oder schlechten Lichtverhältnissen stets verlässlich. Durch seine hohe Messrate von 200 Hz erkennt er Hindernisse auch bei schnellen Bewegungen stets zuverlässig.
-
product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
product
PXI High Density Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-610A-005
The 40-610A-005 is a 8-bank, 8-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Contactless Laser Extensometers
Jinan Testing Equipment IE Corporation
Model LE-05 and LE-15 extensometers measure strain optically, without contacting the specimen, using laser diode technology. The extensometers are self-contained and portable. They may be interfaced with a variety of testing machines and data acquisition systems using the ±10V analog output or bi-directional RS-232 serial port. Operation may be local or remote. A digital display is included. The scanning beam is always perpendicular to the specimen, unlike most laser extensometers. This eliminates errors when viewing through windows in chambers. It also minimizes sensitivity to the distance between the extensometer and the sample. Because the unit measures reflected light, no receiver is required behind the sample.
-
product
PXI 16x16 Matrix Module, 2-Pole, 2A, 60W
40-582-001
The 40-582 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 78 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
