Filter Results By:
Products
Applications
Manufacturers
ECU Simulation
a virtual Electronic Control Unit (Engine Control Unit) used to validate related dynamic systems.
See Also: ECU, ECU Testing
-
product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
product
CAN, CANopen, J1939 Tester
X-Analyser3
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
product
Connector and Breakout Box
ES4640
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
product
FlexRay Interface Device
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Oxygen Sensor Tester And Simulator
7650
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
PXI FlexRay Interface Module
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXI Thermocouple Simulators
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
product
ECU Calibration
Designing an Electronic Control Unit (ECU) is only the beginning. The features in ECUs, such as Powertrain Control Units, are quickly becoming more complex and offering more features. Thousands of variables are now provided for the engineer to modify during the in-vehicle calibration phase, and fine tuning them is as complicated as it is critical. Calibration tools significantly impact the efficiency and effectiveness of the ECU development process. These tools are typically comprised of PC-based software to perform the adjustment of the variables and an ECU hardware interface to provide the connection of the software to the controller. Teams must be able to measure and time-align relationships of inputs and outputs and make real-time modifications.
-
product
ECU Interfaces
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
-
product
ECU Simulator
PT-LabCar
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
product
ECU Simulators
Easily configurable and customizable ECU solutions. Perfect for use as gateway nodes, simulators, automated testers, and ECU replacements.
-
product
ECU Tester
State-of-the-art analog and digital technology are covered in the ECU, measurement and control systems and flexible high performance is required for the evaluation. Verification of reliability is very important because it is an important component further life-threatening people. From previous experience, tester of the ECU has come to our proposed notice that it is better to use a TestStand and PXI is the optimal solution of Peritec ECU tester.
-
product
PN009 – ECU – Diagnostic
*Allow to read and write EEPROM EDC15, EDC17 (BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806.*Read and modify of counter – EDC16, EDC17(BOOT MODE), SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806*Read and change PIN EDC15, SID201, SID801, SID801A, SID802, SID803, SID803A, SID804, SID806*Read and change EEPROM with EDC15 and make OFF
-
product
Automation And Validation Of ECU Tests
ECU-TEST
Softing Automotive Electronics GmbH
Automotive Electronics - ECU-TEST is the universal test automation ECU-TEST was designed for test automation and for the validation of ECUs. Standard test tools are already integrated and can be used together in tests. ECU-TEST is used to design, realize, run and evaluate tests.
-
product
ECU & Bus Interface Modules
ES500
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
product
ECU Software Download Stations
Jackmark Engineering design & manufacture ECU software download stations also known as flash stations, for several industry sectors including automotive, agriculture & utilities. The custom designed stations in either a single unit or multiple stacks provide a secure & reliable system of downloading software to electronic control units. Units are ‘locked in’ during the download phase with visual indicators of download status.
-
product
Simulation
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs.
-
product
Simulation
From structural analysis and computational fluid dynamics to injection molding simulation and advanced, cloud-enabled capabilities powered by Abaqus, SOLIDWORKS® and 3DEXPERIENCE® Works Simulation provide integrated analysis tools for every designer, engineer, and analyst.
-
product
Simulation
Synopsys' high-performance simulation products help engineers find design bugs faster and achieve timely coverage convergence to create high-quality designs. The Synopsys suite of simulation solutions are tightly integrated, best-in-class technologies that allow designers to find bugs quickly and easily, significantly improving the quality of the most complex designs and enabling first-pass silicon success.
-
product
PCI Simulation Modules For Sensor Simulation
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
product
PXI Simulation Modules For Sensor Simulation
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
product
Altitude Simulation
MEDAS
The MEDAS system is a compact altitude simulator that reproduces a wide range of environmental conditions. It allows for testing light- to heavy-duty vehicles, including Non-Road Mobile Machinery (NRMM). It is ideally suited for a range of testing applications, such as durability, RDE replication, emission tests and mapping as well as tests from component to vehicle level. The patented technology inside the MEDAS system allows dynamic changes on the simulated atmosphere with high accuracy. The system can also be moved between different test cells due to its compact design.
-
product
Diagnostic Simulation
Stage
STAGE simulates aspects of Diagnostic, PHM and ISHM Engineering, showing the support capabilities of a System during its useful lifetime. Many types of analysis can be performed on STAGE, including Testability, System Reliability & Mission Success, Sustainability, and Logistics Resource Allocations.
-
product
Environmental Simulation
Simulation of environment. PHOENIX TESTLAB's environmental simulation laboratory is accredited for environmental testing of a multitude of standards.
-
product
Environmental Simulation
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
product
Environmental Simulation
We provide a wide range of systems and devices for environmental simulation. Whether you are carrying out temperature, climate, vibration, corrosion, emissions, altitude, pressure or combined stress testing, we have the right solution and can supply systems in all sizes. From series products right through to customer-specific, process-integrated systems. The choice is yours! For excellent reproducibility and precise test results.
-
product
Environmental Simulation
Is your product heat-resistant? Throughout their useful lives, technical products are subject to a multitude of environmental influences, e.g., heat, cold, oscillations or impacts. This influences their functioning and length of service life. We can find out how the effect and cause are interrelated with an environmental simulation. We will test your products under specific environmental conditions and help you to optimize them for sustainable product development.
