Filter Results By:
Products
Applications
Manufacturers
- CTRL Systems, Inc.
product
Electrical Inspector
The UL101 Electrical Inspector utilizes airborne attachments to safely inspect sealed electrical panels and substations. The UL101 Electrical Inspector allows for early, long-distance detection of arcing, corona discharge, and tracking. Save time and money by reducing transmission/distribution loss and outages.
-
product
18th Edition Testers
Designed to make electrical installation testing safer and more efficient, our range of multifunction testers perform all tests required by 18th Edition wiring regulations.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Loop / PFC Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Insulation Tester
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages. It is a versatile instruments in locating intermittent shorts defective electrical connections insulation and conductor failure and preventing costly repairs & break down insulation value.
-
product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
product
Multifunction Electrical Installation Meter
AMPI-520
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
product
Installation Testers
A Multi-Function installation tester is better then the single function meter. Good quality insulation, a properly working grounding system and active protection assure the safety of people, electrical systems and buildings, and protect them against electrocution, fire and other equipment damage and all of this can be checked by an HT Instruments Installation tester
-
product
Calibration Services
Mors Smitt has a professional calibration center. All electrical measurement equipment can be calibrated (for example; multimeters, current clamps, temperature meters, installation testers, power meters, safety testers, etc.).
-
product
Digital Multimeters
Triplett Test Equipment & Tools
compact digital multimeter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Voltage, DC Current, Resistance, Continuity, Diode Test, Transistor hFE, and Temperature. The rubberized boot provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. The Model 1101-B is well suited for a variety of commercial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads with alligator clips, Type K bead probe and battery (9V).
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Multifunction Installation Testers
Megger multifunction installation testers are capable of performing various electrical tests.
-
product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
product
POLAR ENERGY
4BAAA
Polar Energy (the successor of the Elcontrol VIP 396 energy analyzer) is a multifunctional panel (96 x 96 mm) mounted tool, ideal for remote measurement, display and remote monitoring of electrical quantities.It features a 128×128 graphic display of great visibility and comfortable frontal buttons for direct consultation and setup. It has a wide range of electrical measurements.Compared to the predecessor VIP396, it adds many functionalities that make Polar Energy a modern and user-friendly tool for the user such as the introduction of cyclic connection verification to make installation easy and secure.The connections to the power cables and to the cables of the voltages and currents are carried out via the 2.5 mm2 terminals in the back of the instrument.For the calibration of the currents, it is necessary to use three TAs with a secondary 5 A.It can be used on single-phase, two-phase, three-phase low and medium voltage networks. Advanced features and included analysis software make it an ideal tool for the most demanding professional needs.
-
product
Single-Functional Testers
Electrical installation safety testing is a wide subfield of general electrical safety testing and encompasses both troubleshooting and fault-finding in complex industrial installations and simple, often periodic testing of only specific parts of the installation. The former usually requires the use of multifunctional testing devices, while the latter can be more conveniently done by testers with far fewer test and measurement functions.
-
product
Low Voltage Products and Systems
ABB provides a full range of low voltage solutions to connect, protect, control and measure a wide range of electrical installations, enclosures, switchboards, electronics and electromechanical devices. The business improves the reliability and efficiency of its customers’ activities across all major industries including the residential sector.
-
product
Electrical Safety Tester
GSC60
One instrument for all electrical safety tests and Power Quality analysisGSC60 was designed with the aim of making safety of electrical installations visible and valuable, easily and quickly.
-
product
Single-functional testers
3110
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
product
Multifunction Installation Tester
ProInstall-75-UK
The Beha-Amprobe ProInstall-75-UK, with new advanced features, is the perfect installation testing tool for verifying the safety of electrical installations in domestic, commercial, and industrial applications. Ensure that fixed wiring is correctly installed and compliant with IEC 60364, HD 384 requirements and BS7671 17th Edition wiring regulation meeting local requirements. The ProInstall-75-UK is efficient to use by allowing the user to measure loop impedance without tripping RCDs, eliminating the need to bypass them.
-
product
Partial Discharge Testing Equipment
AR700
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
product
Digital Insulation Testers
This professional Voltage Insulation tester is designed with voltage overload protection and high voltage indicator to safely measure voltage in 50V, 100V, 250V, 500V,1000V and 2500V. It has a dual display when measuring under Insulation Resistance, it simultaneously show the selected voltage range and insulation resistance measured reading. These measurements can be use to evaluate insulation integrity. This troubleshooting tool is a quality control measure at the time a piece of electrical equipment is produced and an installation requirement to help ensure specifications are met and to verify proper hookup. It also use as a periodic preventive maintenance task.
-
product
Digital Multifunction
Contrel Elettronica s.r.l. Company
The DIN rail and front panel multimeters are ideal for installation in secondary distribution panels. Measurement of the main electrical parameters. Measurement of active, reactive and apparent energy. Modbus RTU, Modbus TCP, Profibus, M-Bus protocol. Digital outputs programmable as alarms or pulses.
-
product
Portable Electrical Management Systems
EMS-PT30C
Progressive Industries Portable Electrical Management Systems (EMS) offer quick and easy RV electrical protection. A true plug-and-play application with no installation required. You will feel secure with multi-mode surge, voltage, polarity, and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: voltage(s), current frequency, error code, and previous error code (if applicable). Additionally, the computer is driven by state of the art microprocessors.
-
product
Installation Safety Testers
VDE 0100
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
product
Thermacon Request to Exit Sensor
T-80 and S-80
These units are designed for easy concealed installation in suspended ceilings or on an enclosed metal electrical box is acceptable for use in air handling areas. In addition to the four standard interchangeable detection patterns, others may be custom made.
-
product
Impact Test Apparatus
IT-50
Impact test is an essential physical test prescribed in many standards to test samples for mechanical shock. It is designed to perform such tests. The test is carried out to ensure that the test items have adequate mechanical strength to withstand the stresses and rough handling imposed during installation and use. It is adapted to test various types of electrical accessories such as switches, sockets, plugs, starter seats and other electrical appliances.
-
product
Cable Management Tools and Testers
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
product
Clamp Meters
Clamp meters are handheld devices with multimeter functions and able to measure AC/DC current directly without breaking the electrical conductor. Today’s clamp meters are multi-functional designed and used in HVAC/R, electrical vehicles, electrical installation, motor inspection, engineering, and many other applications. UNI-T clamp meters are well known for its performance, practicality, and reliability.
-
product
Terminal Mechanical Strength Test
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
-
product
Electrical Safety Tester
MACROEVTEST
Multifunction instrument for electrical installation safety testing, power quality analysis and EVSE safety testing
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
