Filter Results By:
Products
Applications
Manufacturers
-
product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
2-Channel DAQ Module
FMC110
Sundance Multiprocessor Technology Ltd.
The FMC110 is a dual channel ADC and dual channel DAC FMC. The FMC110 provides two channels of 12-bit A/D @ 1 GSPS and two channels of 16-bit D/A @ 1 GSPS enabling simultaneous sampling at a maximum rate of 1 GSPS. The sample clock can be supplied externally through a coax connection or supplied by an internal clock source (optionally locked to an external reference). Additionally a trigger input for customized sampling control is available.
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
16-Channel ADC Module
FMC116
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
product
Phased Array Ultrasound Instrument
TOPAZ64
TOPAZ64, a fully integrated, portable 64 channel Phased Array UT device delivering faster, more reliable inspections. It intelligently combines the power of 64 active channels for Phased Array UT applications with the industry’s most advanced Full Matrix Capture (FMC) and Total Focusing Method (TFM) capabilities. Bipolar pulsers provide more energy to punch through thick components.
-
product
DSP FMC Modules
Sundance Multiprocessor Technology Ltd.
FMC Modules with Digital Signal Processors
-
product
FPGA Mezzanine Card
FMC216
The FMC216 is a 16-channel DAC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. It provides 16 D/A 16-bit 312.5Msps (2.5Gsps with x8 interpolation) channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
PCIe/104 OneBank Carrier for Trenz SoC Modules
EMC²-DP
Sundance Multiprocessor Technology Ltd.
The EMC²-DP is a PCIe/104 OneBank™ Carrier for a Trenz compatible SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board and also has I/O pins, using a 100-way Samtec RazorBeam connectors system. The add-on board, called “Sundance External Interface Connector – SEIC” contains LEDs, RS232, USB2.0, HDMI, 1Gb Ethernet and SATA . The “SEIC” can be customize for individual applications and bespoke connectors.
-
product
FPGA Mezzanine Card
FMC160
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.7Gsps (2.85Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. It is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1).
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
4-Channel ADC Module
FMC104
Sundance Multiprocessor Technology Ltd.
The FMC104 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC104 card provides four 14-bit 250 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
4-Channel ADC Module
FMC125
Sundance Multiprocessor Technology Ltd.
The FMC125 is a Quad-Channel Multi-Mode A/D FMC, fully compliant with VITA 57.1 Standards. The card provides four 8-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
product
PCIe/104 OneBank SBC w. Dual 1GHz ARM9
EMC²-Z7030
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-Z7030 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Z7030 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
4-Channel DAC FMC Module
FMC204 – HPC
Sundance Multiprocessor Technology Ltd.
The FMC204 is a quad channel DAC FMC. The FMC204 provides four channels of 16-bit D/A @ 1 GSPS enabling simultaneous sampling at a maximum rate of 1 GSPS. The sample clock can be supplied externally through a coax connection or supplied by an internal clock source (optionally locked to an external reference). Additionally a trigger input for customized sampling control is available. The FMC204 daughter card is mechanically and electrically compliant to FMC standard (ANSI/VITA 57.1).
-
product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
product
FMC Module
NES-FMCA429-CAN
Sundance Multiprocessor Technology Ltd.
The NES-FMCA429-CAN from Nolam embedded systems is the world’s first FMC module combining ARINC ‘429 bus and CAN bus in a single FMC module. The NES-FMCA429-CAN features 2 receive and 2 Transmit ARINC429 channels and CAN bus. Both protocols have Autotest capabilities.
-
product
2 or 4 channel BC/RT/MT FMC Module.
NES-FMC1553-4
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMC’s to be supported on a wide range of existing form factor including but not limited to: PCle, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMC’s can be fitted on a 6U VPX carrier.
-
product
FPGA Mezzanine Card
FMC116
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
1-Channel DAQ Module
FMC160
Sundance Multiprocessor Technology Ltd.
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC160 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
product
PC/104 OneBank Carrier
EMC²-SoM
Sundance Multiprocessor Technology Ltd.
The EMC²-SoM is a PCIe/104 OneBank™ Carrier for a Trenz compatible FPGA and SoC Module and has expansion for a VITA57.1 FMC™ LPC I/O board. It also has I/O pins, using a 100-way Samtec RazorBeam connectors system, the “Sundance Expansion Interface Connector” (SEIC) can be customize for individual applications and bespoke connectors.
-
product
4-Channel ADC FMC Module
FMC103 – LPC
Sundance Multiprocessor Technology Ltd.
The FMC103 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC103 card provides four 12-bit 210 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC103 has the LPC (Low-Pin Count) 160-Pin connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
product
PCIe FPGA Card
PC821
The PC821 is a high-performance, PCI Express card with advanced DSP capabilities and multiple I/O options.It supports one VITA 57.4-compliant FMC+ and one VITA 57.1 compliant HPC FMC site. Both FMC sites are closely coupled to the Virtex or Kintex UltraScale FPGA and a DDR4-2133 SDRAM SO-DIMM.
-
product
FMC Card with DisplayPort Input and Output
TEF0007-02A
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
product
2-Channel DAQ Module
FMC151
Sundance Multiprocessor Technology Ltd.
The FMC151 is a dual channel ADC and dual channel DAC FMC daughter card. The card provides two 14-bit A/D channels and two 16-bit D/A channels which can be clocked by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition there is one trigger input for customized sampling control. The FMC151 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Fixed-Point C6455 DSP Module
FMC645
Sundance Multiprocessor Technology Ltd.
The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), has a high-pin count connector and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces.
-
product
2-Channel DAQ Module
FMC142
Sundance Multiprocessor Technology Ltd.
The FMC142 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides two 16-bit A/D channels at 370MSPS and two 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock. A trigger input is also available for customized sampling control. The FMC142 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1-2010). It offers front panel analog I/O access and can be used in a conduction-cooled environment.
-
product
12ch ADC, 2ch DAC Module
FMC-FADB
Sundance Multiprocessor Technology Ltd.
The fmc-dad board is a 12 ch ADC/ 2 ch DAC channels board using FMC HPC and QSE connectors It has been designed for system requiring a feedback loop mechanism with precise timing, such as the tunning of RF cavities.
-
product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
product
FMC Mezzanine Module
NES-FMC4ADC
Sundance Multiprocessor Technology Ltd.
By default this card only uses signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5mV, and +/-5V. AN advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range og +/-5V that is independent of the chosen gain range.
