Filter Results By:
Products
Applications
Manufacturers
- DragoonITCN
product
Countermeasures Sequential Timing & Amplitude Tester
C-STAT
C-STAT, or Countermeasures Sequential Timing and Amplitude Tester, is a Firing Pulse Interval Test Set, a suite of test components designed to analyze firing pulse timing and amplitudes from a CMDS system such as ALE-47.
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
Volume Flow Rate & Velocity
Lutron Electronic Enterprise Co., Ltd.
Volume Flow Rate & Velocity Testers by Lutron
-
product
Geotextile Water Permeability Tester
TG010
TESTEX Testing Equipment Systems Ltd.
Geotextile Water Permeability Tester, to determine the constant-head water flow capacity (water permeability) within the plane of a geotextile or geotextile-related product, is measured under varying normal compressive stresses, typical hydraulic gradients and defined contact surface.
-
product
Mechanical Hydraulic Tester
RFIK
The RFIK mechanical hydraulic tester provides the ideal solution for servicing and commissioning hydraulic circuits on agricultural and other mobile machinery. The kit comprises of a direct acting flow indicator with built in thermometer, a loading valve and a pressure gauge all built into a strong steel case with a removable lid.
-
product
IEC60529 IPX34 Hand Held Spray Nozzle
IPX34
Shenzhen Chuangxin Instruments Co., Ltd.
The Spray Tester IPX 3/4 is a hand-held test device to verify protection against spraying and splashing water. The water pressure can be adjusted using the flow control knob on the device to give the required flow rate.
-
product
Powder Rheometer
FT4
The FT4 Powder Rheometer® was designed with one purpose in mind - to characterise the rheology, or flow properties, of powders. This remains a primary function today, but the instrument, accessories and methodologies have been continuously developed to the point where the FT4 is now considered a universal powder tester.
-
product
Melt Flow Testers
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
product
Portable Hydraulic Testers
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
product
Flow Leak Testers
If you need high-quality air flow testers, you’ve come to the right place. We carry equipment for mass flow and leak testing, laminar flow, and continuous flow. You have the option of choosing touch screen or standard digital. All our equipment is compact and includes high-performing, state-of-the-art technology. Begin testing your equipment with our premium-grade flow testing equipment. Explore our amazing selection of flow testing equipment.
-
product
Bi-Directional Digital Hydraulic Testers
DHT302, DHT402 Series
The most popular sizes of digital hydraulic tester. Measure flow, pressure, temperature & speed. Flows up to 400 lpm (100 US gpm).
-
product
Environmental Testers
Environmental testers sample and measure environmental elements such as temperature, humidity, sound, pH & air flow.
-
product
CEAST VisualMELT Software
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
product
LED tester
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
product
Plastic Testing Instruments
Aging oven, Charpy/Izod impact tester, falling weight impact tester, heat sealer, lasting adhesive tester, melt flow indexer, notch cutter, oxygen index tester, primary adhesive tester, vicat softening temperature & HDT machine, vacuum leak tester
-
product
Cabin Leakage Tester
The Kanomax Cabin Leakage Tester pressurizes or depressurizes the automobile vehicle cabin to measure the changes in cabin pressure. The control unit consists of a manometer and pressure transducers. The manometer detects the leakage flow, which is calculated by measuring the nozzle pressure relative to static pressure. The tester controls an adjustable fan to maintain static test pressure.
-
product
Primary Current Injection Testers
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
product
Powder Flow Testers
Delivers quick and easy analysis of powder flow behavior in industrial processing equipment. It is ideal for manufacturers who process powders daily and want to minimize or eliminate downtime and expense that can occur when hoppers discharge erratically or fail to discharge altogether.
-
product
Geotextile Water Flow Capacity Tester
TG050
TESTEX Testing Equipment Systems Ltd.
The flow of water within the plane of a geotextile or geotextile-related product is measured under varying normal compressive stresses, with typical hydraulic gradients and with defined contact surfaces.
-
product
Masks Bacterial Filtration Efficiency Tester
Sataton Instruments Technology CO., Ltd
Face Masks bacterial filtration efficiency BFE tester is to determine the bacterial filtration efficiency (BFE) of medical face mask materials by employing a ratio of the upstream bacterial challenge to downstream residual concentration of the tested medical face mask materials. The tester provides certain flow rate of bacterial aerosol. The operator can measure the number of colony forming units passing through the medical face mask material, which is clamped between a six-stage Anderson cascade impactor and an aerosol chamber, expressed as a percentage of the number of colony forming units present in the challenge aerosol.
-
product
Bi-Directional Digital Hydraulic Testers
DHT801 Series
A simplified digital hydraulic tester with a single ON / OFF switch. Measure flow, temperature and pressure in one robust unit.
-
product
Oil Pour Point Tester
Weshine Electric Manufacturing Co., Ltd
WESHINE’s fully-integrated, automatic cloud and pour point apparatus(VS-9612 Cloud and Pour Point Tester) offers precise and convenient flow testing of petroleum products, biodiesel fuels, additives and lubricating oils.
-
product
T8730 AIR FLOW TESTER UNIVERSAL
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
product
High Accuracy Digital Puncture Tester
KT-5000Pi
This product improves the absurdity that the existing Puncture Tester has many errors between the indicated voltage on its meter and the real output voltage, and also that one cannot check how much current flows during test, and then attaches a voltage meter and a current meter. Its accuracy is high due to Digital method adopting a three point adjustment type. Also, for user's convenience and for making easy to connect with automation line, many input, output functions are added. Now, Puncture Tester also should be accurate and a high-grade product
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
product
Core Flow
Quizix Precision Pumps and Formation Response Testers (FRT’s) are the industry standard for core flow studies by operators, service organizations and research laboratories.
-
product
Hydrophobic Powder Wettability Tester
WET1001
We will introduce a hydrophobic powder wettability tester that measures the critical wetting tension of powder materials such as pharmaceuticals and pigments and considers dispersibility and surface energy. flow rate concentration curve .The amount of organic solvent when this powder lump starts to settle is evaluated as a measure of the degree of affinity (hydrophobicity) with the organic solvent.
-
product
Leak Masters
Uson provides automatic non-destructive air leak and flow measurement equipment and solutions used in product development and manufacturing environments for medical device, automotive, electric vehicle battery, packaging and industrial applications. Uson leak testers are highly configurable and are built with premium components ensuring maximum quality, reliability and performance.
-
product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
product
Autoburst
M229
The Autoburst is a hydraulic bursting tester with advanced testing controls. The instrument has automatic flow control allowing bursts to be achieved within the specified time of the standard.
