Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Strain Gauge Simulator Module 4-Channel, 2k
40-265-304
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 1k
40-265-204
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
-
product
Destructive Coating Thickness Gauges
Designed for measuring on a non-metallic substrate or assessing the thickness of a multi-coat paint, Elcometer offer a range of destructive coating thickness gauges such as the Elcometer 121/4 and Elcometer 141 that are portable and easy to use.
-
product
Strain Gauge Test
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
product
Protective Coating Inspection
Kit 6
The Elcometer Protective Coatings Inspection Kit 6 is a comprehensive kit which incorporates all the key gauges and inspection accessories required to assess a structure before, during and after coating has been applied.
-
product
Digital Vacuum Gauge
605
Range : 0 ~ 12,000 microns (0~1600 Pascals). Units of Measure : Microns, PSI, InHg, mBar, Pascals, Torr, mTorr. Over Pressure : 500PSI
-
product
Ultrasonic Velocity gauge
VX
With the hand-held VX Ultrasonic Velocity gauge, you can determine material velocities by measuring a known thickness, entering a known thickness into the VX, and the material velocity will be displayed. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries.
-
product
Small/Medium Capacity Torque Detector
SS series
The SS series torque detector suits to wide variety of torque measurement application, including performance test of motors, pumps, compressors, blowers, turbines and gears. High rigidity results from the unitized cast-casing structure and SS series torque detector can be handled easily as being free from parts replacement on treatment of maintenance, comparing to other type of torque detector such as strain gauges, with non contact signal detection on the detector. 13 models in the series can be provided and chosen among them according to requirement in torque capacity.
-
product
LAP's Laser Gauge For Straightness Measurement Of Bars And Tubes
Check X-Line
This process is unique on the market and was developed with our partner sema Systemtechnik. You receive a verifiable quality assurance of your rods or pipes in the current production. The modular design allows individual configurability and can be easily integrated into the existing system. Benefit from the competence and experience of two strong partners.
-
product
Ergonomics Force Gauges
Series E
Series E push / pull force gauges make job task analysis and ergonomics analysis simple and accurate, ideal for workplace design, strength assessment, and ergonomic studies. Series E presents the ergonomist and other professionals with a simple and economical testing solution. 100 lbF, 200 lbF and 500 lbF (500, 2,500, and 5,000 N) capacity force gauges are available, along with a wide range of attachments for various applications.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
product
Data acquisition software RSIC for force gauges Centor
RSICW-C
With the RSIC data acquisition software, you can record hte measurements of your gauge Centor directly using MS Excel. It makes it easier to record results and ensure traceability and processing; these are the main advantages for using this simple yet powerful software.
-
product
Ultrasonic Thickness Gauges
MMX 6 + MMX 6DL
The new wall thickness gauges MMX-6 and MMX-6DL includes all the features of the MX devices with the additional unique possibility to measure on coated parts without the coating is applied in the measurement (Echo Echo + pulse-echo function)
-
product
PXI Strain Gauge Simulator Module 6-Channel, 1k
40-265-206
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Double Embossed Shrouds
BE-DE
Bemcoil-DE (double embossed) is made from roll and continuous welded 18 gauge 304 stainless steel sheet. Each tube passage is almost equivalent to a 7/8 inch OD tube. It is available in three finishes. A number 2B (semi-reflective) finish on the inside face and a number 4 (polished unidirectional) finish on the outside surface, specified when one side of the shroud is to be painted with black epoxy.
-
product
COMPRESSION, VACUUM AND FUEL PUMP TESTER COMBO SET
MCVK
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
product
Mobile Test Devices
burster präzisionsmeßtechnik gmbh
Device test, strain gauge simulator, sensor test, reference measurement chain
-
product
Tyre Gauge
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
A portable gauge for measuring the air pressure in a tire.
-
product
Differential Pressure Gauge
XP2i-DP
AMETEK Sensors, Test & Calibration
Ultra rugged, intrinsically safe, Differential Pressure Gauge with 0.1% of reading accuracy, capable of continuous vacuum measurement.
-
product
Universal (ID/OD) Presetting Instruments
Pratt & Whitney Measurement Systems, Inc.
If gage setting and calibration is important to you, choose the Labmicrometer Model 900 or 1600 measuring system. Designed for gage calibration laboratories and shop floor environments requiring precise internal and external measurements over long lengths. Additionally, the Labmicrometer is ideal for use as a setting bench and adjusting instrument offering precision setting of inside and outside comparative measuring gages, micrometers, snap gauges, as well as other measuring tools.
-
product
4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System
TCR-600
*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）
-
product
3U OpenVPX High Density Multifunction I/O Board
68CB6
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
product
Dry Film Thickness
Dry film thickness, coating thickness or paint thickness as it is often known, is probably the most critical measurement in the coatings industry. It provides vital information as to the expected life of the substrate, the product’s fitness for purpose, its appearance and ensures compliance with a host of International Standards. In 1947, Elcometer launched one of the world’s first non-destructive coating thickness gauges, the Elcometer 101 Coating Thickness Gauge. For more than 6 decades, the design and production qualities of this rugged and reliable instrument have been the watchwords for all our products and these philosophies are still held today. Elcometer has a comprehensive range of Dry Film Thickness gauges to meet all of your coating inspection requirements.
-
product
Tool, Inspection Depth Gauge, Mini Coax, Receiver
910121156
Used to verify the depth setting of the center conductor of receiver mini coax contacts.
-
product
Pressure Sensors
ESPP-MIT1 Sensor
ES Systems has developed a series of strain gauge pressure transmitters featuring very good accuracy at a low cost. Each module is based on an all-welded hermetically sealed structure in a single stainless-steel piece. The ESPP-MIT1 is a medium isolated pressure sensor suitable for gas or fluid pressure measurements in harsh industrial or HVAC environments.
-
product
4-CH 24-Bit Universal Input USB DAQ Modules (OEM Version Available)
USB-2401
The USB-2401 is a 24-bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels can be programmed to measure different signal types. The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
product
Adjustable Ignition Spark Tester
404
For all ignition systems from high energy electronics to small engines. Tests for no-start conditions and for spark strength.Adjustable gap for spark gap requirements from 0-40,000V. Gauge background makes spark easy to see.
-
product
Drone Thickness Gauge
Multigauge 6000
The Multigauge 6000 Drone Thickness Gauge has been designed specifically to mount onto a drone or UAV. This new technology has already had many successful installations on various models of drone and this is the first dedicated drone thickness gauge available worldwide.
-
product
Compact Coating Thickness Gauges
MP0 Series
The small all-rounders for mobile coating thickness measurement. Leading industrial instrument series for fast and easy coating thickness measurement in corrosion protection and industrial applications.
-
product
JofraCal
AMETEK Sensors, Test & Calibration
JofraCal calibration software ensures easy calibration of RTD´s, thermocouples, transmitters, thermo switches, pressure gauges and pressure switches. It may be used with our well-known temperature calibrators as well as with pressure and multifunction calibrators.
