Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-056
The 40-297A-056 (PXI) and the 42-297A-056 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
3KV High Voltage Test
45EHV/VC20EHV: 4.5inch High Voltage Motherboard for Celadon Element™ 20mm VC20EHV VersaCore™ and VersaJet™ System
-
product
DC Hipot and Megohmmeter
PTS Series
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
product
sbRIO-9235, Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781579-01
Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
product
High Speed-Large Current DC Electronic Load (CC/CV/CR/CP)
PLZ-4WL Series
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
product
Connector Test
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
product
AC Dielectric Test Systems
700-DI
The HIPOTRONICS standard line of AC Dielectric Test Systems are designed to perform high voltage AC tests on electrical apparatus in accordance with IEC60, IEEE 4 and IEC 270 and other national test standards. A variety of mechanical configurations are available to suit different installation conditions. Some models can be supplied in mobile versions when it is difficult to move the test object to the test area. AC Dielectric Test Sets are available in a wide range of voltage and power ratings with exceptional reliability, durability and functionality. No matter what your requirement is, HIPOTRONICS has an affordably priced, highly reliable test solution to meet your needs.
-
product
Large Earth Resistance Tester
WA 180
Wuhan Sangao Electrical Test Installations Limit Co.
WA180 Type Large earth resistance tester,To test substation earthing network(4Ω), Hydroelectric and Thermoelectric Power Plant,microwave(10Ω),lighting rod(10Ω)etc.Using new type variable frequency AC power supply, And adopts microcomputer control and signal processing measures, Solved the problem of interference of the testing process, To simplify the test procedure, To improve the precision and accuracy of the test results, reducing test personnel's the labor intensity and the cost of testing.The instrument can be used to test all kinds of power frequency earth resistance,contact voltage,step voltage etc frequency power parameters and soil resistivity. The instrument adopts the different frequency Anti-interference resistance technology, under strong interference environment accurately measured the frequency under 50Hz data.The maximum test current is 5A,it will not cause the earth device potential too high,and it also has strong anti interference ability, so it can be measured in the case of non power.
-
product
Earth Tester
TAURUS PRECIOHM ET
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
product
Cable Fault Locators
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
product
PXI 2A 32xSPST High Density Power Relay Module
40-137-101
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
product
AC and DC Electronic load
63800 series
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
product
CTEK Battery Analyzer
56-925
The CTEK BATTERY ANALYZER tests with high accuracy the condition of all types of 12V lead-acid batteries including Wet, Maintenance Free, Ca/Ca, Gel and AGM. Easy to use it provides fast, and easy to understand results. Operating voltage range is 8–15V with a test range of 200–1200EN. Simply connect the clamps to the battery and follow the step by step instructions on the display.
-
product
Switch Stick Test Equipment
Hanco units provide a full high voltage electrical test as required by OSHA. Front-loading, top-loading and portable units are available.- Sticks can be tested wet or dry.- Test units are available to test sticks up to 14 or 21 feet maximum length or up to 8 feet for the portable unit.
-
product
1kV, 120 MHz High Voltage Differential Probe Without Tip Accessories and with Auto Zero Disconnect
HVD3106A-NOACC
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Cell Voltage Monitor
N1200 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N1200 series fuel cell voltage acquisitor is specially developed by NGI for fuel cell R&D and production. It is with compact size, high integration, high reliability and fast data transmission. N1200 standalone supports up to 200 channels. More channels can be tested simultaneously under cascade mode. Voltage acquisition range is from -2.5V to +2.5V, which completely covers the voltage range of fuel cell. Real-time voltage data of total 200 channels can be uploaded within 10ms by adopting 100M Ethernet communication. N1200 PC application software supports platform-based test applications, which allows users to customize test files based on the test requirements and process.
-
product
SureTest® Circuit Analyzer
61-164
*Measures voltage drop under load**Hot and neutral conductor impedances*Estimates Load on Line (ELL) up to 15A*Tests GFCIs and EPDs for proper operation*Super-bright OLED display*High accuracies*True RMS*Line and peak voltage*Identifies proper wiring in 3-wire receptacles*Identifies false (bootleg) grounds*Tests without disturbing sensitive loads*Verifies isolated grounds (with 61-176 adapter)*2-year warranty*12A, 15A, 20A load tests
-
product
Capacitor Tester
MIG1212CAP
MIG1212CAP is specially designed for high voltage test on X / Y capacitors with impulse voltage approximate 1,2/50 µs up to 12 kV in accordance with IEC 60384-14 Ed.4. The MIG1212CAP comprises two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape of approximate1,2/50 µs and are combined in an 8 unit high 19" rack. IEC 60384-14 and EN 132400 define the generator.
-
product
Circuit Breaker Test System
AutoScan
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
product
Power Inductor - Impulse Winding Tester
19301A
Chroma Systems Solutions, Inc.
The Chroma 19300 Impulse Winding Tester with high/low inductance test technology has 1000V of impulse voltage and a 200MHz high speed sampling rate that satisfies most power inductor test requirements for a wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value, and LAPLACIAN value functions are able to effectively inspect coils for insulation abnormalities.
-
product
2kV, 120 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3206A
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
DC Power Supply
PDS Series
This series of products is programmable DC switching power supply with high accuracy and single output. It is light and compact, adjustable in voltage and current, and has multiple operating modes. The whole system is completely controlled by the microporcessor (mou), and can easily use the communication interface (re-232) to connect with the computer (PC) to meet the user's requirements for automatic testing and automatic control. The software instructions are completely in accordance with the scpi command. The format makes it easy for users to develop automatic test and automatic control applications. Due to the full digitalization of the system, the data input is completely controlled by the keyboard and knob, which is fast, accurate, and convenient. Can be widely used in electronic product development, device testing, communications industry, laboratories and scientific research institutions.
-
product
Analogue (1kV below) Insulation Tester
1126 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ) and AC voltage.● LED indiction for testing insulation.● Highly efficiency and accurate DC-DC converter.● Battery check function.● Compact and lightweight.● AC voltage measurement can be made without depressing the test button.
-
product
Insulation Testers
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
product
Series Resonant System
HTXZ / 100
Wuhan Huatian Electric Power Automation Co., Ltd.
Suitable for large capacity, high voltage capacitance test and preventive test.
-
product
Accessories for Ratio meter
The CVT Range Extender is an accessory for the ELTEL TRM-100,TRM-150,TRM-200 and ATRM-200 Transformer Ratio Meters and designed to test high ratios of CVTs used on High Voltage Systems. Provides a 1:40 range extension.
-
product
UltraCMOS SP8T RF Switch
PE42582
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
Test Setup For Domestic Mixer Motor
SCR ELEKTRONIKS have developed TESTING SET UP FOR MIXER MOTOR for carrying out performance test and High Voltage test of mixer at final stage. It consists of Voltmeter, Ammeter and Watt meter for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of HV test. HV test is provided with tripping cut off concept. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
product
Insulation Testers
Sanwa Electric Instrument Co., Ltd
Is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
product
Rail Traction Inverter Test System
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
product
Handy Size Digital Multimeter
HH2107A
Basic Accuracy 1.0%. Large LCD display 2000 count, 21mm figure height. Manual Ranging at your choice (19 Range). High Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 20MΩ
