Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782109-01
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module - The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified … synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,2 m
763061-02
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
Type X2 double-shielded GPIB cable, 10 m
763061-10
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
Multifunction Data Collection and Analysis System
2002
The Model 2002 DME System is a state of the art, multifunction data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER), Digital Fault Recorder (DFR), Dynamic Disturbance Recorder (DDR), and Continuous Recorder data in conformance with PRC-002-1 and PRC-018-1. All data recorded by the DME system is stored in IEEE C37.111 format and named in conformance with IEEE C37.232. The system also has a software option to enable the Phasor Measurement Unit (PMU) feature to provide streaming data in conformance with IEEE C37.118.
-
product
cPCI Backplane
PICMG 2.0
VECTOR Electronics and Technology, Inc.
The specification for PCI based industrial computers is called CompactPCI. It is electrically a superset of desktop PCI with IEEE 1101.10 mechanical form factor. Vector offers RoHS compliant 3U and 6U cPCI backplanes sold separately or integrated into VectorPak™ EMC subracks or chassis.
-
product
NetXpert XG2 10G Tester
#TXG200
*Ethernet Speed certification of copper and fiber optic systems up to 10Gb*Complete active network testing over copper, fiber and Wifi systems*Cable qualification to IEEE standards*TDR & fiber cable length measurement*PoE testing up to 90W (PoE++)
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
product
PCI-GPIB+, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows, Onboard GPIB Analyzer
778033-01
The PCI‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCI slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCI‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
2-port/4-port GigE PCI Express Card
AX92322
The AX92322 is a GigE compliant PCI Express card supporting two or four independent Gigabit Ethernet ports. It features PCI Express x4 interface and has four powerful independent Intel® Ethernet Controller i210-AT. The GigE frame grabber card supports 9.5KB Jumbo Frame and IEEE 1588 to enable faster and more accurate throughput of data. The AX92322 is built for machine vision and surveillance applications in industrial IoT field. This PCI Express frame grabber card is designed to help customers develop and deploy machine vision and surveillance applications which will greatly benefit through reduce the cost and simplify system integration. Moreover, the AX92322 has a wide operating temperature of 0˚C to 70°C, making it suitable to be used in most server environments. The advanced GigE frame grabber runs on Windows® 7, Windows® 10 and Linux.
-
product
BitPhyer Tools
BitPhyer is a family of hardware platforms used to test the IEEE 802.3™ MAC, Flow Control, PCS and RS layers for Ethernet devices, including Automotive Ethernet. This platform is based on Xilinx FPGAs and custom built hardware which are used to create a flexible bit-level based test system.
-
product
Web Sensor with PoE
T3610
PoE Web Sensor with built-in relative humidity and temperature sensors. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Power over Ethernet feature according IEEE 802.3af is supported. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Battery Monitoring System
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
product
Ultra Low Power Radios
IoT
IEEE 802.11b/g/n-compliant Wi-Fi Radio (2.4 GHz)Ultra-low-power hostless Wi-Fi IoT Module features QCA4010 RadioSingle Stream System (1x1), 20 MHzIntegrated RF front end and PCB trace antennaHostless IoT application development platform with large internal memoryUART AT command set for optional external MCU hostAllJoyn supportWi-Fi Protected Setup SupportIPv4 / iPv6, TCP and UDP Protocol Supported on Chip, Offloading the Host ControllerIdeal for cost effective Internet of Things (IoT) Applications
-
product
RFID Chamber
– 80dB RF shielded enclosure (inside dim.- 5’ high x 5’ wide x 7’ long)– Fabrication, Construction, and Transportation– Free standing shielded enclosure design including structural support system– Enclosure will be installed over a continuous 1/8″ dielectric underlay and polyethylene vapor barrier– Modular wood-core panel construction– Bulkhead connector panel – (1) 12” x 12”– RF shielded doors – (2) 2’ x 2’– One (1) Antenna Sinclair Model SP-440-SF2SNF– Shield test per IEEE –STD 299- supersedes MIL-STD-285 (Tested @ 1 GHz)– RAM
-
product
Qty5-Double Shielded Type X2, 2m GPIB Cables
777781-25
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Basic CMC Extender for PrPMC, PMC, and PMC-X
4320
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
product
Battery Capacity Tester
BLU-C Series
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
product
Linear Power Supplies Programmable, Digital Control, Rack Mount, Ultra Low Ripple/Noise
Series MAT
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
product
Satellite Clock
TCG 01-G
The TCG 01-G is a highly accurate, full featured GPS and GLONASS (GNSS) clock. With enhanced cyber security features that support NERC CIP requirements, the TCG 01-G is designed for use in modern day smart grid / smart substations, electricity distribution, transmission, generation protection and control systems. The clock synchronizes multiple IEDs (Intelligent Electronic Devices) within a network, including protection relays and remote telemetry units to enable accurate time stamping. The TCG 01-G supports IEEE 1588 v2 (PTP) and IEC 61850.
-
product
Powerline Analyzer
SHARK 100-S
Amperis introduces one of its most advanced Sub-Meters. This high performance product is designed to measure the use of electrical energy with an accurate degree of billing and send that information by the most advanced means of communication. The unit supports RS485, Ethernet RJ45 or IEEE 802.11 Wi-Fi ethernet. This allows it to be installed anywhere in the building or construction and communicate with the Cetral Backup Software easily, quickly and automatically.
-
product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
product
Acoustic Test Serivices
Audio, acoustics and electroacoustics testing and assistance for your product. * Audio Laboratory equipped with precision instruments from Bruel and Kjaer and others. * Emphasis is on product and component analysis not general acoustics. * TIA, ANSI, IEEE, ITU-T, ETSI, AES, UL, EN, IEC standards expertise.
-
product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
product
Non-steady-state probe for thermal conductivity measurement
TP02
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
product
Receiver Conformance Test Application for IEEE 802.3bm
M8091BMCA
IEEE 802.3bm Receiver Test Application for 25GAUI-1 Chip-to-Module, Chip-to-Chip, Cable and Backplane.
-
product
GNSS Satellite Clock
TTM 01-G
The TTM 01-G is a reliable and accurate GPS and GLONASS (GNSS) clock with sub-microsecond timing that is used to synchronize IEDs (Intelligent Electronic Devices) in the power industry and other industries where precise and reliable timing is required. As with all Tekron GPS clocks, the TTM 01-G has electrically isolated outputs, providing excellent noise immunity. The TTM 01-G supports both NTP/SNTP (IEC 61850) and PTP (IEEE 1588 v2).
-
product
Precision Time Protocol
IEEE-1588
Meinberg Funkuhren GmbH & Co. KG
As a high-stability Grandmaster Clock in IEEE 1588-2008 networks, the MEINBERG NTP time servers with highly accurate PTP clients ("slaves", such as the PTP270PEX or PTP SYNCBOX ) At the same time as the current absolute time.
