Filter Results By:
Products
Applications
Manufacturers
IR Sensor
Detect infrared radiation and produce a measurable signal of the detected amount.
- Optomistic Products
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Color Sensor
The color sensor product family includes both RGB (Red, Green, Blue) and high-accuracy XYZ light sensors for precise color measurement, determination, and discrimination. XYZ sensors are capable of providing xy chromaticity co-ordinates in accordance with the CIE 1931 color map. The ams color sensors include filters to block unwanted IR light in the visible spectral range, enabling highly accurate color measurement. Their high sensitivity coupled with their wide dynamic range make them well suited to continuous color temperature measurement of ambient light in display management systems, and automatic-white-balance assistance in camera applications. Some products have additional IR channels to assist with IR light source identification.
-
product
Pyroelectric IR Detectors and Sensors
Excelitas Pyroelectric Infrared Detectors define the leading edge of motion detection technology, offering a variety of both digital and analog Pyroelectric IR Detectors to serve a wide range of applications in smart home, smart city, IOT, burglary detection and security systems. With Pyroelectrics available in Single-, Dual- and Quad-Element configurations we offer you a wider range of different sized infrared sensor surfaces, which directly translates to enhanced performance and sensitivity. Excelitas sensors are representing the innovative forefront in mid-IR sensor devices. The family of DigiPyros enables smart home and smart sensing applications with low current requirements.
-
product
Tunable Filter Spectrometers
MKS Instruments' platform of innovative optical analyzers based on Tunable Filter Spectroscopy (TFS™) provides real-time gas analysis, while delivering customers a substantially lower total cost of ownership. TFS™ can be utilized from UV (Ultra-Violet) through IR (Infra-Red) spectral regions. MKS TFS™ sensor platforms have been on the market since 2008 with more than 2500 systems deployed.
-
product
QTI Sensor
555-27401
The QTI Sensor is a close-proximity infrared emitter/receiver that is able to differentiate between a dark surface) with low IR reflectivity) and a light surface (with high IR reflectivity). These little sensors can be very handy for line following, maze navigation, or sensing the outer rim of a SumoBot ring. Wiring options allow it to be used digitally for fast black/white line following, or as an analog sensor to detect different shades of gray. A daylight filter is built into the sensor.
-
product
*Irradiance And Dosage Sensors
This sensor family provides cosine corrected irradiance measurement in W/cm² and dosage measurement in J/cm². The sensors are calibrated over their entire spectral range, and are thus ideal for irradiance and dosage measurement of UV, VIS and IR LED based light sources
-
product
SparkFun RGB Light Sensor
ISL29125
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity of the general red, green, and blue spectrums of visible light while rejecting IR from light sources. You can then use these color sensor readings for the purposes of logging and finding patterns, or creatively calculate and make control decisions in your electronic projects.
-
product
IR Temperature Sensor with GigE (Manual Focus)
FLIR A35
The FLIR A35 is a thermal imaging temperature sensor for condition monitoring, process control/quality assurance, and fire prevention applications. The A35 integrates seamlessly into existing systems, offering comprehensive visual temperature monitoring. As part of the Ax5-Series, the A35 is among the only thermal imaging temperature sensors on the market to provide temperature linear output through GenICam™ compliant software.
-
product
IR Thermometers
Is a sensor that consists of a lens to focus the infrared (IR) energy on to a detector, which converts the energy to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature variation.
-
product
Dual Blackbody Wide FOV
Dual blackbody, all reflective background IR target projector is used to characterize WFOV IR sensor systems. It features a broadband, 3 to 14 micron range, reflective IR target technology for the most accurate and stable differential targets, controlled background radiance, a 5º FOV with 36º uniform background.
-
product
Smart Probes
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse, and mor...
-
product
High Performance TIC 320x240 (3 Button)
FLIR K55
With a FLIR K55 TIC in hand, you can attack fires more strategically, maneuver through smoke more easily, and save lives. The K55 displays crisp thermal images on a bright LCD, helping you navigate better and expedite critical decisions. The 320 x 240 pixel IR sensor and FSX™ Flexible Scene Enhancement produce detail-rich imagery at a 60 Hz frame rate that keeps up with the action.
-
product
IR Sensor
The sensor measures a very useful 0.17 mm in thickness and is made of plastic. Essentially it is a piece of robust plastic that can be used “bare” – without protective housing, such as a metal casing commonly used by other producers. The sensor it is less than 0.2 mm. thin and it is made using plastic membrane. This configuration makes the sensor so robust it can be used “bare” – without protective housing such as a metal container. Due to the fact thatSince the sensor chip can be used applied bare, means it can be used in a totally new ways, which can re-defines todays the current view on application design and reduces the cost of the entire system, and not just the sensor-element as such.
-
product
Thermal Infrared Sensors
Excelitas “Thermal IR Sensors” represent a wide range of Pyroelectric Detectors, Thermopile Detectors and IR sensor modules. Our leading edge IR sensing technologies are used for motion detection, presence monitoring, temperature measurement and gas detection to enable smarter homes, improved energy efficiency, better health, safer home security and a more expansive and connected IOT. In addition to our wide offering of off-the-shelf devices, we also specialize in customized solutions for your specific needs.
-
product
SparkFun Triad Spectroscopy Sensor
AS7265x (Qwiic)
The SparkFun Triad Spectroscopy Sensor is a powerful optical inspection sensor also known as a spectrophotometer. Three AS7265x spectral sensors are combined alongside a visible, UV, and IR LEDs to illuminate and test various surfaces for light spectroscopy. The Triad is made up of three sensors; the AS72651, the AS72652, and the AS72653 and can detect the light from 410nm (UV) to 940nm (IR). In addition, 18 individual light frequencies can be measured with precision down to 28.6 nW/cm2 and accuracy of +/-12%. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Si1145 UV / Ambient Light / Proximity Sensor
SEN-36002
SEN-36002 is a highly integrated carrier board designed for the Si1145 UV, Ambient Light and Proximity sensor IC from Silicon Labs. This sensor has 100mLUX resolution, and has a dynamic range of 1 LUX to 128 kLUX with IR correction. This means that whether your application is indoors in poor lighting conditions or outside in full sunlight, this sensor has you covered. In addition, we added a high power LED (150mA max, 20 degree) to take full advantage of the proximity sensing capability of this IC - something you won't see on most competitive carrier boards. Integration is easy with 4 x 4-40 sized mounting holes at the corners of the PCB and signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. The INT pin is also broken out for interrupt capability.
-
product
Gunshot Detection & Localization System
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
product
TMD37003 cRGB Color and Proximity Sensor
SEN-36004
Fully integrated carrier board designed to get the most out of the TMD37003 cRGB (color with IR compensation) and Proximity Sensor from AMS. This means that the board includes a 1.8V-5V input range LDO and high-speed signal voltage translation on all IO pins. In addition, we've added a high output white LED that is tuned to the light temperature range of the TMD37003 IC. This makes sensing color of close-proximity objects possible, such as in robotic color sorting operations. As on many of our boards, we've included 4-40 sized mounting holes to make installation easy. The IC functions are interfaced via a 0.1" header, which includes power (Vdd and GND), I2C interface (again, fully translated) and a 3.3V input to power the proximity (IR) LED. The on-board LED is turned on with a logic 'HIGH' applied to the LED pin and is powered with Vdd.
-
product
IR Linear and 2D Sensor Array Modules
Excelitas offers Linear and 2D IR Imager Arrays based upon our Thermopile Technology. All Arrays are provided as plug-and-play Modules featuring a sensing chip, robust metal housing with focusing lens, a PCB with microprocessor for calibration and bus interface and a quick connector for streamlined plug-and-play integration. We offer 8-pixel, 16-pixel and 32-pixel Linear IR Imager Array Modules for field-proven effectiveness in scanning presence detection, non-contact temperature measurement, smart-home products, and office electronics. Custom solutions also available upon request.
-
product
4 MP OV4682 RGB IR Camera Module
e-CAM40_CUMI4682_MOD
The e-CAM40_CUMI4682_MOD is a 4 MP RAW RGB-IR MIPI OV4682 camera module with the M12 S-mount lens holder. The e-CAM40_CUMI4682_MOD RGB IR camera module is based on OmniVision's OV4682 1/3" Optical format CMOS Image sensor, that captures high-resolution images and videos as well as IR information. Its dual RGB-IR Camera capabilities allow it to bring a host of additional features to machine vision applications and by combining RGB - IR in a single camera module reduces the total cost and saves space. Customers can evaluate e-CAM40_CUMI4682_MOD with See3CAM_CU40 over USB 3.0 interface and e-CAM40_CUTK1 over MIPI interface. e-CAM40_CUMI4682_MOD camera module can stream the 4MP(2688x1520) unprocessed 10-bit RAW data video upto 40 fps. Also read OV4682 RGB IR camera module frequently asked questions.
-
product
In-Line IR Sensor
ILA
10:1 Distance to Target Ratio, 32 to 932F. Dwyer Series ILA Non-Contact Sensors, measure temperatures from 32 to 932F (0 to 500C) and provide a linear 4 to 20 mA, 0 to 5 VDC or thermocouple output. The 2-wire signal is compatible with almost any indicator, controller, recorder, data logger, etc., without the need for special interfacing or signal conditioning.
-
product
*LED Measurement – UV, VIS, NIR
UV, VIS, and IR LEDs are replacing traditional light sources and are enabling new applications. Ophir offers a number of choices in LED power measurement - use the LED sensor finder to find the right sensor. For cases where a complete image of the beam distribution is necessary, use a beam profiling camera.
-
product
Sensor
VL53L1
The VL53L1 is a state-of-art Time-of-Flight (ToF) laser-ranging miniature sensor. Housed in a miniature and reflowable package, it integrates a SPAD (Single Photon Avalanche Diodes) array, physical infrared filters and optics to achieve the best ranging performance in various ambient lighting conditions, with range of cover glass options.Unlike conventional IR sensors, VL53L1 uses ST’s latest generation direct ToF technology which allows absolute distance measurement whatever the target color and reflectance. It provides accurate ranging up to 4m and can work at fast speed (60Hz), which makes it the fastest miniature ToF sensor on the market.With patented algorithms and ingenious module construction, VL53L1 is also able to detect different objects within the Field-of-View with depth information (histogram) at 60Hz. Scene browsing and multi-zone detection is now possible with VL53L1, thanks to software customizable detection array for quicker “touch-to-focus” or mini depth-map use cases.
-
product
Gesture, Color Sensors & Proximity Detection
The gesture product family performs advanced gesture detection, proximity detection, digital Ambient Light Sensing (ALS) and color sensing (red, green, blue and clear). It also implements optical pattern generation for barcode transmission and remote controls. The gesture sensor modules provide a highly integrated solution offering five essential functions to enable a touchless interface and to optimize the end user experience of communications and consumer electronics equipment. Gesture detection uses four directional photodiodes to sense IR energy emitted from the integrated LED, converting the measurements of reflected IR light into information about physical
-
product
2MP Global Shutter Camera
See3CAM_20CUG
See3CAM_20CUG is a 2MP global shutter monochrome USB 3.1 Gen1 Camera. This industrial USB camera is based on OmniVision's 1/2.9" OV2311 Image sensor with 3μm x 3μm pixel OmniPixel® 3-GS technology. This monochrome USB camera can capture high frame rate images without any motion blur and its IR sensitivity helps to produce stunning image quality even at the Near Infrared (NIR) regions. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux.
-
product
LWIR Micro Thermal Camera Module
Lepton®
The FLIR Lepton® is a radiometric-capable LWIR OEM camera solution that is smaller than a dime, fits inside a smartphone, and is one tenth the cost of traditional IR cameras. Using focal plane arrays of either 160x120 or 80x60 active pixels, Lepton easily integrates into native mobile-devices and other electronics as an IR sensor or thermal imager. The radiometric Lepton captures accurate, calibrated, and noncontact temperature data in every pixel of each image.
-
product
Smart Probes
A wide selection of rugged smart probes for your sensing needs. From non-contact IR sensors to a full range of sensor types including Temperature, Humidity, Process, RTD, Thermocouple, pulse.
-
product
hyperspectral imaging sensor
Hyper-Cam
The Hyper-Cam is a lightweight and compact hyperspectral imaging sensor which uses Fourier Transform Infrared (FT-IR) technology. This advanced high-performance spectrometer allows to detect and identify substances either gases or solids from a distance of up to 5 kilometers. It provides real-time chemical imaging as well as unparalleled spatial and spectral information about the IR targets under measurement.
-
product
Visible / Infrared / Imaging Test System
System 1808
Testing Low-voltage CCDs and IR FPAs; Military, science-grade and medical CCDs or IR FPAs; CMOS ROICs and multiplexers; CMOS sensors. Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your your device, not on your test system.
-
product
Sensor Scene Modeling and Analysis Software
INSSITE
INSSITE is a sensor scene modeling and analysis environment. Different sensor types and modalities, spanning radar (synthetic aperture radar [SAR], ground moving target indicator [GMTI], detection and ranging, radio frequency [RF] communications), visible/infrared (passive electro-optical/infrared [EO/IR], laser radar [ladar], thermal IR), can be evaluated against high fidelity scenarios constructed by the user.
-
product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
