Filter Results By:
Products
Applications
Manufacturers
Incremental Encoders
Measure movement by producing quadrature output codes corresponding to the amount of motion.
See Also: Encoders, Encoder Test, Absolute Encoders, Linear Encoders
- TEAM SOLUTIONS, INC.
product
Resolver-to-Digital Converter
MSX-RDC-17
The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.
-
product
6 Channel Encoder Input Controller
PCI323
The PCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
-
product
PCI Express Analog and Digital I/O
826
Six advanced 32-bit counters Directly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement 16 analog inputs, 16-bit, 300 ks/s 8 analog outputs, 16-bit, 900 ks/s 48 digital I/Os with edge capture Watchdog timer, 3 stages
-
product
High-Precision XY Stage
V-731
Physik Instrumente GmbH & Co. KG
Reference-class XY stage. Travel range 205 mm × 205 mm (8"). Unidirectional repeatability to 0.1 μm. Velocity to 200 mm/s. Incremental encoder with 10 nm resolution.Optionally with stepper motor.
-
product
Machine Vision SBC With AMD® Ryzen™ Embedded V1807B And V1605B APU, DisplayPort, HDMI, 2 GbE LAN, 2 IEEE 802.3at PoE GbE LAN And Vision-specific I/O
MIRU130
*AMD® Ryzen™ Embedded V1807B and V1605B APU*2 DDR4 SO-DIMM for up to 16GB of memory*2 GbE LAN and 2 IEEE 802.3at PoE GbE LAN*2-CH camera trigger outputs*2-CH LED lighting control*1-CH incremental quadrature encoder input*4 isolated DIO
-
product
Absolute Optical Encoder Kit Version
A2K
The A2K absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2K reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
product
Incremental > EX-Proof Encoders - Hollow Shaft
Incremental > EX-Proof Encoders - Hollow Shaft
-
product
TMR Gear Tooth Encoders
MultiDimension Technology Co.,Ltd.
Geartooth Encoders of MultiDimension Technology (MDT) are non-contact incremental encoders for rotary speed and position measurement. Based on MDT’s unique Tunneling Magnetoresistance (TMR) sensor technology, they provide orthogonal differential square wave signals with high quality, along with an index signal and their inverse signals. The GE-T series are designed for 0.3~1.0-module gears with different teeth numbers. (Gear is the optional product).
-
product
Incremental Encoder Simulator
ENC-SIM01
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
product
Displacement and Encoders
INCREMENTAL digital Transducers are mainly designed for displacement measurement in machine tools and other industrial applications. The sensors are characterized by high precision and are absolutely dust and waterproof. The used materials permit applications in heavy industrial environments.DISPLACEMENT Transducers are suitable for measurements of small distances up to 50mm. They are characterized by high accuracy and repeatability, reliability and fast response. Digital ENCODERS operate on optical or magnetical principal and are offered with incremental or absolute coded outputs. They are suitable for precision industrial applications.
-
product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
product
Quadrature Incremental Decoder Interface for VMEbus
VME323
The VME323 is an Intelligent Quadrature Incremental Decoder VMEbus Board which can be configured for interfacing quadrature incremental encoders with or without an index channel. In index mode up to sixteen encoders with two quadrature channels and an index channel can be connected, and in non-index mode up to twentyfour encoders with two quadrature channels can be connected. The VME323 operates on two encoder input channels and decodes a pair of out-of phase signals in order to increment or decrement a counter.
-
-
product
Counters and Timers
Orbit Controls counters and timers are designed for connection to practically all industrial sensors and pulse sources . They can be used as process monitors to display the process variable to be measured or as process controllers for control and monitoring tasks. The devices display and process pulses and frequencies, as well as quadrature signals from incremental and absolute encoded rotary encoders. In addition to information on the display, the devices also generate data and analog outputs and monitor preselected limit values. The process parameters are entered via the keyboard so that the display is calibrated in the required units and the output signals, serial interfaces and limit values are optimized.
-
product
Motion Control Board, PCI
APCI-8001-1
*Axis control for 1 servo or stepper motor*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders *or SSI absolute encoders
-
product
P104 Synchro/Resolver Measurement Board
73SD4
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
product
Speed Switch
UDS1000
Features • Works with remote / external quadrature pulse frequency output sensor / incremental encoder (NPN or PNP) • DPDT relay changes state when shaft direction reverses • Reverse-over-speed setpoint adjustment from 0.5-5,000 rpm • Relay resets when reverse motion stops • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • Explosion proof/NEMA 4X housing • UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
Rotary Encoders
Incremental encoders
You will always find the suitable incremental encoder here: from the cost-efficient standard versions to the high-resolution design with 320,000 pulses per revolution - in various designs and with robust magnetic or precise optical scanning. Optionally with HTL, TTL, or sine signals and all common mechanical interfaces.
-
product
Absolute Optical Encoder
A2
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Incremental Encoder
ED1
Chuan Sheng Electronics Co., Ltd.
● Easy installation, high-speed pulse generator, high-speed rotation control, and more.● Ф 38 diameter with high resolution up to 1024P/R● Push-pull output can use for NPN or PNP input meter
-
product
Encoders
At Variohm we have a range of encoders we can offer. Our range includes Absolute Encoders and Incremental Encoders as well as Lift Measuring Systems.
-
product
6 Channel Encoder Input Controller
CPCI323
The CPCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
-
product
Closed-Loop Motor Controller
MS320
Master and Ratio-Follower modes and programmable input functions. Options include analog speed feedback input, analog setpoint inputs and relay outputs. Works with incremental shaft encoders and pulsefrequency output shaft speed sensors. Optional explosion proof enclosure or NEMA 4X enclosure kit.
-
-
product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
product
Incremental > Standard Encoders - Hollow Shaft
Incremental > Standard Encoders - Hollow Shaft
-
product
Incremental Encoders
Incremental encoders provide a relative position with respect to a "home" or zero position. US Digital offers incremental encoders as kits ready for assembly and shaft-equipped encoders, using both optical and magnetic technologies. Also in stock and immediately available are encoder modules and encoder components such as disks and hubdisks.
-
product
Rotary Encoders
The family of dia 50mm incremental rotary encoders features an improved water resistance compared to standard models.
-
-
