Filter Results By:
Products
Applications
Manufacturers
Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
- Virginia Panel Corporation
product
9050TR - 50 Module, 2-Tier Solution with Platform
The rack mountable 9050TR receiver is designed to accept 9025 and 9050 ITAs and is essential to support advanced mass interconnect requirements. This 50-module solution can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can also be intermixed to establish custom interfaces which are ideal for functional and system testing applications.
-
product
Mass Interconnect
Mass Interconnect is a mechanical interface that simplifies connection between the power supplies, instruments and switching to the Device Under Test (DUT) in a test environment. In the illustration here, a test receiver is connected to the front of the modular instrumentation, in this case, a PXI chassis.
-
product
GHz Elastomer Sockets
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
product
AGC Coaxial Connectors
Teledyne Marine AG Geophysical Products
Coaxial Inline and Bulkhead Cables and ConnectorsWaterproof electrical coaxial interconnect for high shock, extreme applications
-
product
Ethernet Switch/Router
VME-682
Curtiss-Wright Defense Solutions
Enabling the vision of inter-networked heterogeneous military and aerospace systems in the Global Information Grid (GIG), Curtiss Wright's VME-682 FireBlade provides Systems Integrators with a fast, secure and unified approach to interconnect subsystems, chassis, cards, and compute nodes within any given platform using 1 and 10 Gigabit Ethernet links.
-
product
Portable Test Platform
FTB-4 Pro
The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.
-
product
Couplers
Smiths Interconnect range of passive coaxial products include couplers of various types (Wilkinson, Directional and Branchline) designed specifically for established reliability applications to provide optimal performance operating in assigned frequencies ranging from UHF to Ku-Band. The couplers featured below have been developed and qualified to operate in extreme operational environments whilst providing designers and system architects with reliable and robust products produced by a manufacturing team experienced in the production of critical application hardware.
-
product
JTAG Test Software
JTAG Technologies software has been subject to a program of continuous development for over 20 years. The first products, launched in 1991 formed the start of our 'Classic' range of software and featured the first automatic boundary-scan test program generator (ATPG) for PCB interconnects plus associated test execution and diagnostics software. In 2006 JTAG Technologies launched it's new flagship tools platform JTAG ProVision.
-
product
Switching Matrix
MUX
The Analog Signal Switch Unit serves as a 6-bus interconnect for 128 pins each to the Analog Measurement Unit (AMU05) for the In-Circuit test.
-
product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
SPICE software for Opto-Electronics
OptiSPICE is the first circuit design software for analysis of integrated circuits including interactions of optical and electronic components. It allows for the design and simulation of opto-electronic circuits at the transistor level, from laser drivers to transimpedance amplifiers, optical interconnects and electronic equalizers.
-
product
Interface Pin
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
product
ITA, S6, 6 Module, With Protective Cover
410122100
The S6 ITA Frame has a powder coated finish adding an extra layer protection against the elements. It is an integral part of this rugged Mass InterConnect system. The S6 ITA has module positions screened on top for ease of module placement. Protective Cover included.
-
product
Resistive Components
Diamond is the best thermal conductor on earth. Combined with a low dielectric constant, it is an excellent RF dielectric material for high-frequency applications in which thermal performance is equally critical. By applying cutting-edge thin film process and extensive millimeter wave design experience, Smiths Interconnect has created a high-performance line of resistive components. The resulting products, our Diamond RF Resistives® resistors, terminations, and attenuators, are significantly reduced in size and unparalleled in average and peak power handling.
-
product
64x64 Matrix
TS202A
Universal Switching Corporation
Designed from scratch to improve on the legacy Precision Filters Model 4164, the TS202A uses the absolute latest in component technology. Many engineers still use manual patch cords & patch panels to interconnect sensors, recorders, scopes and other instrumentation in test & evaluation labs.
-
product
USB
The introduction of USB 3.2 and USB4 along with the Type-C connector ushers in a new era of unprecedented performance for consumer electronics that can now utilize this universal interface for power, data and display. Positioned as the primary high-performance interconnect for the next decade, developers are ramping up their USB3.2 / USB4 expertise. From engineering validation to compliance test, trust the experts at Teledyne LeCroy to help ensure product compatibility for next generation USB systems.
-
product
Mini Modular, High Density Connector System
H Series
The modular design of the Smiths Interconnect H Series allow custom configurations from standard off-the-shelf components without the cost and lead-time of custom tooling. The H Series offer a variety of designs to meet specific customer needs for extreme high density signal, power, and coaxial interconnect solutions.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
ScanWorks Boundary-Scan Test
ScanWorks Boundary-Scan Test
The Boundary-Scan Test (BST) Development Software is one of the several configurations of the ScanWorks boundary-scan (JTAG) test and on-board programming environment. Test engineers can quickly develop interconnect tests and device-programming actions for use on first prototype board to accelerate the board bring-up process. Then tests can be exported for use in manufacturing and repair facilities.
-
product
SMP Connectors
Pasternack SMP connector (sub-miniature push-on connectors) category contains mostly RoHS and REACH compliant product varieties. The SMP connector category includes dozens of configurations including coaxial sub-miniature push-on connectors, PCB mounted, non-sealed and hermetically sealed terminals and shrouds. Our subminiature push-on SMP connectors are built to precise microwave and RF industry specifications and are part of over 40,000 in-stock RF products. Connectors in SMP series from Pasternack are manufactured in male or female gender with a 50 Ohm impedance. Pasternack's SMP subminiature connector are available in straight or right angle versions as well as bulkhead or mount-less options. These connector designs include solder or solder/solder attachment methods. Pasternack’s SMP connectors are miniaturized push-on interconnects commonly used in high density, blind-mate systems that can operate up to 40 GHz. Standard sub-miniature push on connector items are offered in a high frequency 40 GHz version as well as a low frequency 8 GHz version and are also available in smooth bore, limited detent and full detent styles. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMP connector series is in-stock. Not just in stock, these subminiature push on connectors will also ship the same day as they are purchased.
-
product
9050 - 50 Module, 2-Tier Solution
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
product
BMS Manufacturing Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
product
CorLogic PLC
Created to meet the demands of Industry 4.0, this IIoT-ready PLC is the perfect equipment to interconnect your machinery, systems, and cloud smartly, deploying performance and connectivity in a very cost-effective device.With large processing capabilities, smart I/O, and support for a wide variety of communication protocols.
-
product
Flexible Waveguide
Flann offers a number of solutions for flexible waveguide interconnect including waveguide-coaxial-waveguide and semi rigid. Traditional flexible waveguide solutions are available on request.
-
product
Signaling Gateway Solutions
Service Providers are making the transition to 4G, and 5G is coming, but legacy connectivity for voice, SMS and IN applications still remains an absolute requirement. SS7 TDM interfaces must be maintained to meet the demand to interconnect different networks and multi-protocol solutions are required to connect divergent circuit and packet switching architectures. SS7 isn’t retrograde – it’s traditional. It’s still the most robust, high performance, and reliable signaling solution out there and it’s needed today more than ever.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
USB Type-C Interconnects Compliance Test Software
S94USBCB
Use the S94USBCB software to test, debug and characterize your USB Type-C cable and connector designs. The PathWave TAP based test sequencer automates the network analyzer (VNA) for each test and generates a comprehensive HTML report. When run with L8990M switch matrix, it enables 20-ports fully automated test without port re-connection.
-
product
12 Channels 1.0 ~ 17.0 Gb/s (200Gbps) Pulse Pattern Generator and Error Detector
CA9806-12
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
product
Gold Probes
4900 Series
The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.
-
product
Interconnect Test Leads
142-1
This 64 inch pair of test leads connects with many different testing accessories and probes. Especially those found in typical test lead kits and assortments. The ends terminate in universal size 4mm banana plugs.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
