Filter Results By:
Products
Applications
Manufacturers
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
PD Surveyor with RFI & EMI Diagnostics
PDS200
The Doble PDS200 is a combination survey tool that uses radio frequency interference and electromagnetic interference diagnostics to find signs of partial discharge.This hand-held instrument is an ideal tool for a condition based maintenance program, allowing you to quickly find insulation defects in motors, generators, transformers, cable terminations and additional substation components.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Interference Detection And Mitigation
Now more than ever, it’s critical to protect military systems from the threat of GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also GPSGlobal Positioning System is a navigation satellite system. See also signal jamming and spoofing by using anti-jamming GPS and spoofing detection solutions.
-
product
Interference Lithography Gratings
Interference lithography is an optical nanolithography technology for the fabrication of extensive periodic nanostructures. Critical dimensions of less than 50 nm can be realized. At AMO two interference lithography tools are installed. One setup for extensive, high quality gratings with fixed periods, the other more flexible tool allows quick prototyping. We offer grating fabrication on silicon, silicon dioxide and other substrates with tailored pitch, etch depth and size.
-
product
Interference Locating System
SeeWave®
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
product
Interference Modeling And Simulation
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
product
Interference Simulation System
GSS7765
Combined with Spirent’s powerful GSS7000 or GSS9000 Series simulators, the GSS7765 interference generator creates the ultimate tool for testing against external jamming and unintentional interference. The GSS7765 enables you to create and generate custom waveforms, helping you to defend your systems against real-world threats.
-
product
Noise & Interference Generator
GPS7500
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
-
product
Generators
Radio Pulse Signal Generator
The Software Signal generator allows to to produce radio pulse signals of various pulse rate and frequency at the DAC output.
-
product
Generators
Frequency-Modulated Signal Generator
The Software Signal generator allows to produce frequency-modulated signals at the DAC output.
-
product
Generators
Pulse Signal Generator
The Software Signal generator allows to produce pulse signals with various pulse ratio and frequency at the DAC output.
-
product
Generators
Sinusoidal Vibration
Software application Sinusoidal vibration is used for testing products resistance to vibration impact at different frequencies and ranges. It is included into software complex ZETLAB VIBRO, supplied together with VCS ZET017-U. The program is available in VCS menu of ZETLAB control panel.
-
product
Generators
Classical Shock
Software Classical shock is used for testing specimen resistance to shock impact. As the Software Classical shock is activated, at the output of shaker control system ZET 017-U there is formed a signal with pre-set parameters. Types of signals generated:
-
product
Generators
OUR CHALLENGE“To drastically reduce the weight and size of Constant Potential X-Ray generator while maintaining first class performances”To successfully meet this challenge, our engineers have worked at designing an exceptional new X-Ray insert. This highly compact X-Ray tube combined with a revolutionary cooling system and a multiple output carrousel can definitely be considered to be the most versatile X-Ray generator ever developed. In addition, performances are not compromised in any way whatsoever.
-
product
Generators
Linear Frequency-Modulated Signal Generator
The Software Signal generator allows to produce frequency modulated signals with linear sweep at the DAC output.
-
product
Generators
Noise Generator
The noise type to be generated is to be selected from the context menu: right-click the section with the noise name and select the noise type you need.
-
product
Generators
Random Vibration
Random vibration Software program is used for testing the specimen resistance to random vibration impact. This program is a part of vibration controller ZET017-U.
-
product
Generators
Sine Signal Generator
The Software Sine generator allows to produce sine and constant voltage signals at the DAC output.
-
product
Generators
We offer a wide range of power supplies, current and voltage supplies, frequency references, RF generators, transceivers.
-
product
Generators
Signal Generator
Signal Generator is used for forming signals of various shapes, amplitude, and frequency at the output channels of ADC and DAC modules and FFT spectrum analyzers. Functionally, the Signal Generator software replaces stationary generators used in laboratories.
-
product
Generators
Vibration Shock
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
product
Generators
GE is bringing generator technology and performance to the next level. We engineer and build our generators to meet the demanding specifications that keep you on the leading edge of efficient, reliable output. Our equipment installs quickly, integrates easily, operates reliably and delivers more power. With over 12,000 generators shipped since 1901, GE understands your challenges, and offers a complete range of configurations and cooling technologies to meet industry needs.
-
product
Generators
Amplitude-Modulated Signal Generator
The Software Signal generator allows to produce amplitude-modulated signals at the DAC output.
-
-
product
Generators
Generating Signal From a File
The Software Signal generator allows to produce signals from binary and text files at the DAC output.
-
product
Generators
Saw-Tooth Signal Generator
The Software Signal generator allows to produce triangular and saw-tooth (descending, ascending) signals at the DAC output.
-
product
Electromagnetic Interference Analysis Program
EMI Analyst™
EMI Analyst (U.S. Patent # 7,222,033) is the premier tool for ascertaining compliance with EMI requirements imposed by regulatory agencies.EMI Analyst is an electromagnetic interference analysis program that combines all four facets of EMI analysis into a single design package.
-
product
Interference & Compatibility Evaluation System
ICEy
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
