Filter Results By:
Products
Applications
Manufacturers
LED Sources
emit light as a reference or to illuminate.
See Also: Light Sources, Optical Light Sources
- Optomistic Products
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
LED Solar Simulator
LumiSun-50
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
product
Outdoor Surface Mounted
HYLO
Available as uplighter, downlighter and up-/downlighter. Choice of multiple colours of LED light sources and a variety of beam angles. The up/down version offers the possibility to use two different colours of light and two different beamangles within one single fixture. Up to 80% energy savings compared to traditional light sources. High light output due the latest generation of Luxeon/Cree LEDs in combination with high quality optics. Massive aluminum CNC housing for optimum cooling properties. Built-in 180-264 VAC power supply for easy installation.
-
product
Fiber Optic Inspection Microscope
80761
The Miller 400x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment. Includes 2.5mm universal adapter cap and zipper case.
-
product
Incoherent Sources
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
-
product
Color Tests
LED-Check
LEDs are the standard light source in car cockpits. It is not sufficient to find out if a LED shines, or not. The LED needs to have precisely the specified brightness and color to fulfil its function.The FiberVision LED-Check system tests up to 250 LEDs in less than one second.
-
product
PLD Systems
Pulsed Laser Deposition
Is a versatile thin film deposition technique. A pulsed laser (~20 ns pulse width) rapidly evaporates a target material forming a thin film that retains target composition. This unique ability of stoichiometeric transfer of target composition into the film was realized first by the research team led by Dr. Venkatesan at Bell Communications Research, NJ, USA, nearly 30 years ago while depositing high temperature superconducting (YBa2Cu3O7) thin films. Since then, PLD has become the preferred deposition technique where ever thin films of complex material compositions are considered. Another unique feature of PLD is its ability for rapid prototyping of materials. The energy source (pulsed laser) being outside the deposition chamber, facilitates a large dynamic range of operating pressures (10-10 Torr to 500 Torr) during material synthesis. By controlling the deposition pressure and substrate temperature and using relatively small target sizes, a variety of atomically controlled nano-structures and interfaces can be prepared with unique functionalities.
-
product
LED based light source
iQ-LED
Image Engineering GmbH & Co. KG
The most flexible, 22 channel, LED based light source is the heart of all adaptive lighting productsCreate your own light by adjusting the 22 channels to your needs. You can simulate standard light sources, reconstruct the daylight distribution from dawn till dusk, create patches of a high saturated color chart, or reconstruct the spectral distribution of a measured light source. By using the individual channels you can even measure the spectral sensitivities of a camera.
-
product
Lighting Maintenance
Lumen maintenance is the most useful gauge to determine the lifetime or useful light output rating of an LED light source.
-
product
Pulsed Source Measure Unit
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
product
Light Flicker Meter
LiFli
The LiFli light flicker meter enables fast evaluation of light sources on the flickering part (flicker / flicker). Especially in the case of LED lamps, the flicker portion can be determined only by one measurement, since it is in the range of 0% to 100% for these luminous means.Audio features enable the flicker to be reproduced acoustically. A voltage output for further analysis by means of oscilloscope or voltage analyzer is available.
-
product
Mini Multimode Power Meter and Mini LED Source
The KD Optics Mini Multimode power meter and Mini LED source are designed for the 850nm and 1300nm testing of multimode links, fibre continuity testing, connector testing, transmitter power testing etc.
-
product
Bench-Top Type ASE Light Source
ASE(Amplified Spontaneous Emission) light sources are low-coherent light sources ,which combines the both features of high intensity like laser and broad spectrum like LED. Output stability is greater than those of LD and LED, and therefore they are suitable for high accuracy measurement applications. With the use of rare-earth-doped fluoride fibers, the plentiful lineup of FiberLabs light sources includes the 540 nm-, 850 nm-, 1300 nm-, 1480 nm- and SCL-bands that other companies do not provide.They are the best light sources for FBG sensors, OCT, fiber optic gyroscopes, gas sensors, and fluorescence excitation, as well as for measurement of optical components. The bench-top type is easy to use as a stand-alone light source and the modular type is convenient for integration into equipments.
-
product
O-E PROBE
O-E probe is the unit to convert optical signals to electrical signals. It can be connected to Oscilloscopes or data loggers via a BNC connector and monitor the conversion waveform. It can acquire the optical signal easily by just pointing the optical fiber probe at the light source. Recently, more and more light sources utilize optical modulation for next generation lighting such as LED. Acquiring the emission timing is required to measure the emission phenomenon of the light source. This O-E probe unit is the ideal tool for these tasks.
-
product
Broadband Optical Source - PXI
SLED 1000 Series
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
product
SLD Light Source
The SLD light source is a light source to emit low-coherence light with a broad spectrum like LED and high brightness like LD. Light emitted from a narrow active layer like LD effectively couple to the fiber. SLD light source can be used for optical measurements and sensors, including fiber optic gyroscopes and OCT. FiberLabs provides fiber-output SLD light sources in different wavelength bands from visible to near-infrared light. Our lineup includes bench-top types convenient for experiments and easy-to-integrate module types.
-
product
LED light sources
MLED4
Photocatalysis, ultraviolet analyzer biological genetic engineering, molecular genetics, medical and health, biological products, pharmaceutical research, health and epidemic prevention, dye chemical industry, petroleum chemical industry, textile industry, etc.
-
product
LED Light Source
FOD 114
The LED Light Source FOD 113 or FOD 114 is a light weight and a very small size portable device which has been created to become as popular as a cellular telephone or a pager. The devices of this series are equipped with a universal optical interface which allows quicker hook up to the line, thus saving time for complete measurements. The LED Light Sources meet TIA/EIA-526-14A requirements for coupling power into multimode fiber.
-
product
Optical Radiation Safety Test
EN62471-C
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
product
Spectroradiometer
SpectraScan® PR-730
The SpectraScan® Spectroradiometer PR-730 is JADAK’s enhanced sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Light Source
pE-300white
CoolLED's pE-300white offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. The pE-300white Light Source can be fitted directly to the microscope or specified with a liquid light guide. The system is a mercury-free alternative that is safer, more controllable, and repeatable than conventional high-pressure gas discharge illuminators. Spectral coverage is from the UV (DAPI excitation) to the Red region (Cy5 excitation). The system is perfect for hospital and regular research laboratory environments.
-
product
Non-Contact H.V. Detector
375 HP
Standard Electric Works Co., Ltd
● Protection class : IP65.● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV● Bright LED visual indication● Frequency range: 40~70Hz● Flashlight funcion●Wider angle for voltage detection(120°)●Audible indication● Easy-to-prove method● Self-test function● Power source : 1.5V "C" type battery × 3● High impact nylon casing● Non-contact work by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Suitable for indoor and outdoor use● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
product
LED Analyser
Feasa
Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order:
-
product
LED Test Instruments
Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
product
Standard & Top Paint Inspection Gauges
121/4
The Paint Inspection Gauge Top model has an internal carousel allowing each of the three cutters to be selected easily together with a cross hatch adhesion tester.Compact and convenient, ideal for paint thickness measurement in confined areasMade of anodised aluminium for durabilityBright LED light source for clear visionTop Model can hold one cross hatch cutter & three standard cutters which are locked tight, a simple rotation of the cutter holder changes the cutting tool.
-
product
Remote Sensors
The most versatile and popular sensors we make. The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. All these sensors have the "on-target" green LED indicator
-
product
Industrial Intelligent Spectrometer
OHSP-250 Series
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
Radiometric color measurement is an important application of spectrometers. LED manufacturers use color measurement to classify LEDs (classification criteria: good or bad functions, color brightness standards, etc.) to ensure product consistency and quality stability. Screen display manufacturers use radiometric measurements to calibrate screen colors to determine if they are within the standard range. LED radiation measurement is also very useful in horticulture, because LEDs are also a major part of plant research and greenhouse light sources; in addition, in biomedical applications, such as therapeutic instrument measurement.
-
product
Spectrometer & Colorimeter
Spectroradiometer is widely used to measure the spectral, photometric and colorimetric parameters of all kinds of lighting sources which usually include relative spectral power distribution P(λ), chromaticity coordinate (x,y), (u,v), correlated color temperature(CCT), color rendering index(CRI), dominant wavelength, peak wavelength, spectral bandwidth, color purity, color ratio, luminous flux, Illuminance, luminance, spectral transmittance and reflectance, etc. PIMACS provides different types of spectroradiometers and colorimeter to meet the requirements in laboratories or on production lines. They are applied in the measurement for general light sources, LED & OLED products, displays, etc.
-
product
Power Meter and LED Source
PM23 and LS20DV
The PM23 and LS20DV power meter and LED source are top of the range units for multimode testing of multimode libre links. The PM23 power meter is also calibrated as standard at 1550nm making it suitable for measuring singlemode links when used in conjunction with a suitable source. The LS23DV has 850nm and 1300nm switchable outputs from 1 port and a visible tracer from the other.
-
product
Light Sources
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements，and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
