Filter Results By:
Products
Applications
Manufacturers
-
product
MIMO Tester
Qosmotec Software Solutions GmbH
The QPER MIMO Tester is a handover tester einriched with phase shifter that helps engineers to make mobile networks fit for modern standards like LTE or HSPA+.
-
product
MIMO Vibration Controller
Spider-80M
The Spider-80M platform is based on the efficient Spider-80Xi architecture and is dedicated to MIMO VCS control and MIMO structural testing applications. Each Spider-80M chassis features 8 outputs capable of carrying out 6-degree of freedom MIMO testing. One Spider-80M chassis and multiple Spider-80Xi chassis can chain together to form a very large system with up to 504 input channels.
-
product
MIMO Vibration Control Overview
MIMO Testing has gained a huge momentum in the past decade with the development of multiple shaker table systems, the availability of Multiple-Input Multiple-Output (MIMO) controllers, and the readiness of the standards (e.g., Mil STD 810G method 527 and IEST DTE 022 working group recommendation). The Multiple-Input Multiple-Output (MIMO) Control System includes the following:
-
product
Multiple-Input Multiple-Output (MIMO) FRF Testing
EDM Modal MIMO FRF Testing includes a dedicated test setup and operation process flow using multiple simultaneous shakers to acquire FRF signals. Using a large channel count data acquisition system (i.e., Spider- 80X or Spider-80Xi), this shaker excitation method provides much higher efficiency and accuracy for the FRF measurements while minimizing local stresses on the test article.
-
product
Multiple-Input Multiple-Output (MIMO) Sine Test
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic. The FRF signals of each measurement DOFs with respect to defined reference DOF will be constructed. The output drive level can be defined to run the test under no control strategy, or the response of a control channel can be specified to run the test in a closed loop.
-
product
MIMO Antenna Assembly for Shield Box
HDRF-MIMOST2570
MIMO Antenna setup assembly customized for HDRF-series shield boxes
-
product
802.11n MIMO RF Shielded Test Enclosure
JRE 0709-B
Containing all the capability of the larger JRE enclosures, the compact 0709-B is ideal for small wireless devices such as; 802.11n MIMO WLAN access points, VoIP devices and other small RF devices.Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
product
Handheld Network Tester
T-BERD/MTS-5882
The T-BERD/MTS-5882 is extremely versatile, enabling the cell site technician to address all key tests with one, lightweight, handheld tester; including: Fiber Inspection: Dirty fiber connections are the #1 cause of network downtime. Microwave back-haul: The majority of microwave backhaul links around the world are still microwave. Enhanced Cable Diagnostics: Environmental factors can damage the CAT X shielded twisted pair cable connecting the microwave antenna. Fronthaul: Avoid dangerous tower climbs with CPRI testing including BERT, PIM detection, MIMO diversity, RET, and VSWR. Backhaul: In addition to packet testing across error-prone microwave hops.
-
product
Modal Analysis
The Modal Analysis package is part of m+p Analyzer, m+p international's dynamic signal analyzer for noise & vibration measurements and analysis. It provides a complete set of tools for observing, analysing and documenting the vibrational behaviour of machines and mechanical structures. Software modules are available for classical and operational modal analysis, shaker measurements (SIMO and MIMO) as well as for ODS, SDOF and MDOF analysis. A modal model validation module is also provided.
-
product
Modal tests
Modal Testing and Modal Analysis - SIMO, MIMO, and ODSEffective and affordable modal testing and analysis solution for SIMO, MIMO, and ODS testing methods. The modal test is an indispensable tool to determine natural frequencies and mode shapes of any structure. With our solution, you are able to excite the structure with an impact hammer or modal vibration shakers and easily measure the responses. Import or draw your geometry for rich visualization and animation of your structures.
-
product
Multi-Axis Vibration Control
m+p VibControl provides coupled and uncoupled multi-axis vibration testing (MIMO) in a closed control loop. Test modes include random, sine, shock and time domain replication (road load simulation). Multi-axis motions are characteristic of field environments. The more a vibration test can replicate the field environment, the more realistically it can induce a vibration stress loading equivalent to that experienced by the product in the field.
-
product
Multi-channel Synchronous Receiver
SRS6000
Many EW, SIGINT and MIMO applications begin with channel-to-channel synchronization; however, that one step can take months to achieve. The SRS6000 and its in-built auto-calibration algorithm make this a task of minutes - not months. In addition, should your cabling or setup change, the calibration routine will automatically adjust.
-
product
Multiple Shaker Control
EDM Multi-Shaker Control (MSC) is a software option included in the EDM testing package along with VCS. Multiple Shaker Control provides one centralized interface to interact with multiple controllers running separate tests at the same time. Multi-shaker controllers are not time synchronized unlike in MIMO VCS, in which all drives are time synchronized.
-
product
Multi-Port Antennas
*Contains between 4-12 ports*Multi-band antennas with separate high and low band ports*Deploy 4x4 (MIMO) on both high and low bands*Independant tilt control for each band
-
product
Multiport Electronic Calibration Module (ECal), DC To 20, 6-ports
N7564A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 20 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
Multiport Electronic Calibration Module (ECal), DC To 9 GHz, 6-ports
N7562A
A series of multiport ECal that cascade-able up to 36-ports which makes it possible to calibrate a wide frequency range from DC up to 9 GHz without making numerous connections during calibration process. Ideal for multiport measurement application with VNA in such as high-volume PA/FEM, massive MIMO antenna or high-speed digital interconnect test applications
-
product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
product
NI-5793, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782512-01
The NI‑5793 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5793 modules.
-
product
Outdoor Nodes
The upgraded Outdoor Nodes have been developed by the NITLab team and support MIMO operation. The new version of the Outdoor Nodes are equipped with 802.11a/b/g and 802.11a/b/g/n wireless interfaces. They also feature 2-core Intel cpus, new generation solid state drives and usb web cameras. Last but not least, each node is equipped with light, temperature and humidity sensors.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
ALL-OUTDOOR RADIO SYSTEM
FreeMile 5 GE
SAF FreeMile 5 GE MIMO all-outdoor system is a Licence-free 5 GHz gigabit radio for Ethernet packet data transmission. Making use of ground breaking 2x2 MIMO technology, the SAF FreeMile 5 GE MIMO delivers up to 210Mbps (105Mbps full-duplex) of real throughput combined with a high packets-per-second performance.
-
product
Antenna Test Chambers
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
product
Attenuator Banks
HYTEM offer different RF attenuation systems that allow to perfom simultaneous types of tests on multiple RF links (handover for instance). Multiple configurations are available : Standard, MIMO, Link separation, Spécific.
-
product
Automated Wireless Testbeds
octoBox
The STACK-BENCHTOP, STACK-16 and STACK-SNB personal testbeds, emulating real-life wireless environment, range in size from a desktop/benchtop model to refrigerator-sized testbeds on wheels. The compact size of the octoBox enables wireless test and development engineers to perform fast, comprehensive and repeatable testing in their offices rather than inside large isolation chambers or in test houses. OctoBox testbeds support 802.11ac or 4G MIMO devices.
-
product
Channel Emulator/Fading Simulator
The channel emulator/fading simulator is a measuring instrument for reproducing the actual radio wave propagation environment of mobile communication.It reproduces the fading environment defined by 3GPP and virtual environment of multiple channels such as MIMO, HetNet.It will contribute to improving development and verification efficiency of the latest mobile communication system such as 5G NR, LTE-Advanced and IoT.
-
product
CMX RF Port Extender
CMX-Z25
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
product
Compact WCA Noise & Vibration analyzer
AD-3651
Noise & vibration analyzer, from in-vehicle order tracking to MIMO analysis. Compact WCA for analysis of noise and vibration for in-vehicle order tracking analysis.The long time experience and know-how of A&D in the automobile field of instrumentation and listening to user suggestions are what gives the A&D model the lead with its unmatched specification and functions. Best of all is its compact size and light weight. At the same time, all the functions you would expect to find in multi channel noise and vibration analyzers are included, plus more enhanced features.
-
product
CPS-8910 , Switch Device for PCI Express
784307-01
PCI Express, Cabled Switch Device—The CPS‑8910 is designed for large multiple-input, multiple output (MIMO) expansion configurations and system control on the PXI platform or software defined radio devices. The CPS‑8910 provides two PCI Express upstream ports and eight downstream ports for seamless system expansion. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel MIMO systems. You also can connect multiple CPS‑8910 switch boxes to a single PXI Express chassis to create massive MIMO systems with a Software Defined Radio Reconfigurable Device. The large data throughput capacity makes the CPS‑8910 an ideal data aggregator for massive MIMO systems. You can use the CPS‑8910 with copper or fiber-optic cables.
-
product
DUAL RF Multiple-Input/Output
FMC-SDR400
Sundance Multiprocessor Technology Ltd.
FMC-SDR400 is a Dual RF multiple input/output module (MIMO) based on AD9361, 70MHz – 6GHz RF transceiver and AD9656 ADC for baseband sampling of less than 70MHz (input only in this range). A software selectable gain and tunable RF bandpass front-end section provides high RF sensitivity by allowing rejection of out-of-band-of-interest interfering signals.
